• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.155-158
• /
• 2002

In general, TVC(Thermal Vapor Compressor) is used to boost/compress a low pressure vapor to a higher pressure for further utilization. The one-dimensional method is simple and reasonably accurate, but cannot realize the detail as like the back flow and recirculation in the mixing chamber, viscous shear effect, and etc. In this study, the axisymmetric How simulations have been performed to reveal the detailed flow characteristics for the various ejector shapes. The Navier-Stokes and energy equations are solved together with the continuity equation In the compressible flow fields. The standard $k-{\epsilon}$ model is selected for the turbulence modeling. The commercial computational fluid dynamic code FLUENT software is used for the simulation. The results contain the entrainment ratio under the various motive, suction and discharge pressure conditions. The numerical results are compared with the experimental data, and the comparison shows the good agreement. The three different flow regimes (double chocking, single chocking and back flow) have been clearly distinguished according to each boundary pressure values. Also the effects of the various shape variables (nozzle position, nozzle outlet diameter, mixing tube diameter, mixing tube converging angle, and etc.) are quantitatively discussed.

• 대한기계학회논문집B
• /
• 제25권8호
• /
• pp.1005-1012
• /
• 2001

When vortex tubes are applied to enhance the coefficient of performance of refrigeration system, the smaller one is preferable. However, the existing vortex generator with a nozzle hole diameter of 0.5mm was not suitable due to chocking of the nozzle hole. Therefore, experimental investigation was made to find an appropriate geometry of vortex generator, which could give a comparable effect of energy separation to commercial ones without chocking problem. The tested vortex generators were tangential and spiral types, which had single inducing channel with larger cross-sectional area than that of conventional multi-hole ones. The experimental result showed that the performance of the spiral type was better than that of the tangential one. As a small size of spiral one, the diameter of cold-end orifice is proposed to an half of tube diameter for the application to refrigeration system, while cold mass fraction ratio is 0.5∼0.6 for a desirable operation.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.106-109
• /
• 2005

The Coanda effect has been used extensively in various aerodynamic applications to improve the system performance. The primary flow in Coanda ejectors is attached to the ejector wall and is expanded inducing a secondary flow. This will probably lead to the mixing of both primary and secondary flows at a down stream section. Very few works have been reported based on the optimization on such devices. The main objective of the present study is to numerically investigate the flow field on a typical Coanda ejector and validate the results with the available experimental data. Many configurations of the Coanda ejector have been analyzed. The effect of various geometric parameters of the device on the expanding mixing layer has also been obtained. The computed data agree fairly well with the experimental data available.

• 한국안전학회지
• /
• 제8권4호
• /
• pp.120-126
• /
• 1993

This work was carried out to investigate the effects of solid mass flow rate, mean particle diameter and mesh number of screen packing material on minimum carrying velocity, which defined as the superficial gas velocity of the upper limit of chocking phenomenon. Vertical pneumatic conveying was studied on a 4.6cm 1. D. pipe, 180cm in length. Experiments were performed in both the empty and the screen-packed pipe. It was also examined the effect of superficial gas velocity, solid mass flow, mean particle diameter, and mesh number of packing material on pressure drop. Minimum carrying velocity in screen packed-pipe was lower than that in an empty pipe. besides minimum carrying velocity was decreased with increase in mesh number of screen packing material. The pressure drop In vortical packed-pipe was Increased with superficial gas velocity, mean particle diameter, and mesh number of screen packing material.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.168-172
• /
• 2008

Three different geometry shapes of the blade leading edge in a centrifugal compressor were investigated in this paper. Numerical simulation was done to analyze the effect of the leading edge shape on the performance of the centrifugal compressor. The result shows that compared to the blunt leading edge, the circular leading edge will raise the chocking mass flow. The pressure ratio and efficiency will increase obviously. Using elliptical leading edge will get a further improvement on the performance than circular leading edge. The analysis of the flow field shows that the leading edge often causes flow separation near the inlet; using circular leading edge and elliptical leading edge will reduce the separation. What's more, using circular and elliptical leading edge will also reduce the wake loss near the outlet of the impeller. In a centrifugal compressor, using circular or elliptical leading edge on the splitter will improve the pressure loading distribution of main blade near the position of the splitter leading, which will increase the pressure ratio.

• 조명전기설비학회논문지
• /
• 제16권4호
• /
• pp.38-45
• /
• 2002

내본 논문에서는 뇌서지에 의해서 발생하는 컴퓨터를 비롯한 전자기기의 장해에 대한 보호대책을 제안하기 위해서내 국내의 뇌보호설비에 대한 규격과 지침에 대한 기술적인 문제점을 분석하였다. 인하도선의 설치방법에 따른 인하도선과 인입용 금속관을 통하여 흐르는 전류사이의 관계를 검토하였으며, 인하도선계에 미치는 표피효과의 영향을 평가하는 실험을 수행하였다. 그 결과 인하도선을 인입용 금속관에 전기적으로 접속한 때 인하도선과 금속관은 하나의 도체로 작용하며, 표피효과와 쵸킹효과 때문에 뇌격전류는 인하도선보다도 금속관을 통하여 훤씬 많은 전류가 흘렀다. 따라서 뇌격전류에 의한 인하도선의 전위상승으로 야기되는 정전유도와 측면방전 등의 악영향을 억제하기 위해서는 인하도선을 인입용 금속관과 건물의 철골 구조체에 전기적으로 접속하는 것이 매우 효과적이다.