• 한국위험물학회지
• /
• 제6권2호
• /
• pp.95-104
• /
• 2018

Gas-liquid bubble column reactors are extensively used in industrial processes. A detailed knowledge of bubble size distribution is needed for determining the mass transfer in gas-liquid film. Experimental data on bubble size distribution and liquid-side mass transfer coefficient($k_L$) were used to calculate the estimated time to saturation in bubble column reactor. Also, the gas flux was evaluated to the liquid-side mass transfer coefficient($k_L$) and solubility data for hydrogen sulfide($H_2S$) and chlorine($Cl_2$) absorption into water. Simulation results show that $H_2S$ absorption time to 50 % of saturation concentrations are 611 sec and 1,329 sec when bubble diameters are 0.5 mm and 4.5 mm, while absorbing 1 % $H_2S$ gas. In case of $Cl_2$, absorption time range 657 to 1,400 sec when bubble size range 0.5 mm to 4.5 mm, while absorbing 1 % $Cl_2$ gas. Calculated simulation results can be used in the design of emergency relief bubble reactors.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2524-2527
• /
• 2007

Solid propellant gas generators (SPGG) play a role as a turbopump starter in liquid propellant propulsion systems by supplying pressurized gas to power turbines for engine start. For such a purpose, the propellants should burn with a relative low flame temperature and the combustion gas should not contain corrosive constituents such as chlorine compounds. In accordance with these requirements, stabilized AN-based propellants have been usually used as the most appropriate oxidizer for propellant compositions. However, the burning area of the propellant intends to increase to satisfy the required mass flux because of its low burning rate. Consequently the burning area incensement brings on the SPGG size augmentation. A flow restriction such as filters is applied to decrease the SPGG size by rising up the combustion pressure resulting in increasing the burning rate. The feasibility of the size reduction of SPGG by the employment of filters have been studied. The preliminary results of this study show that the considerable reduction of SPGG size would be achievable just by installing a filter with relatively high pressure loss coefficient.

• Bulletin of the Korean Chemical Society
• /
• 제32권2호
• /
• pp.472-476
• /
• 2011

Sodium chlorate/hydrochloric acid mixtures were used to chlorinate activated arenes and the $\alpha$-position of ketones. This chlorination method was used to produce selectively mono-, di-, and trichlorinated compounds by controlling the molarity of sodium chlorate. This reagent proved to be much more efficient and easier to handle than chlorine gas.

• 대한예방의학회:학술대회논문집
• /
• 대한예방의학회 1996년도 제48차 추계 학술대회 연제집
• /
• pp.287-288
• /
• 1996

• 대한화학회지
• /
• 제20권4호
• /
• pp.266-269
• /
• 1976

액체분자는 고체와 같은 그리고 기체와 같은 자유도를 가진다는 가정하에 액체의 상태합을 유도하였다. 이 상태합을 아르곤, 염소, 암모니아, 벤젠 등의 액체에 적용하여 이들 액체의 열역학적 성질들을 계산한 결과가 실험치와 잘 일치하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.145-149
• /
• 2004

It is necessary for managing a perfect process for degasing aluminum molten metal according to the increase of a grade of aluminum and its alloy products. There are some methods that have been used to manage a degasing process in recent years, such as an injection method that uses aluminum molten metal powder and chemicals supplier and input method that supplies argon and nitrogen, or chlorine gas by using a gas blow-tube. However, these methods show some problems, and it shows that it is a difficult process to handle. pollution due to the producing a lot of toxic gases like chlorine and fluoride gas. irregular effects, and lowering work efficiency due to the excessive processing time. The problems that are the most fatal are the producing a lot of sludge due to the reaction of aluminum molten metal with chemicals. loss of metals, and decreasing the life of refractory materials. In order to solve these problems. this paper develops a technology that is related to aluminum continuous casting molten metal and monolithic degasing apparatus. A degasing apparatus developed in this study improved the exist ing methods and prevented environmental pollution wi th smokeless. odor less, and harmlessness by using a new method that applies argon and nitrogen gas in which the methods used in the West and Japan are eliminated. The developed method can significantly reduce product faults that are caused by the production of gas and oxidation because it uses a preprocessed molten metal with chemicals. In addition. the amount of the produced sludge can also be reduced by 60-80% maximum compared with the existing methods. Then. it makes it possible to minimize the loss of metals. Moreover. the molten metal processing and settling time is also shortened by comparing it with the existing methods that are applied by using chemicals. In addition, it does much to improve the workers' health, safety and environment because there is no pollution. The improvement of productivity and prevent ion effects of disaster from the results of the development can be summarized as follows. It will contribute to the process rationalization because it does not have any unnecessary processes that the molten metal will be moved to an agitator by using a ladle and returned to process for degasing like the existing process due to the monolithic configuration. There are no floating impurities due to the oxidation caused by the contact with the air as same as the existing process. In addition. it can protect the blending of precipitation impurities. Because it has a monolithic configuration. it can avoid the use of additional energy to compensate the temperature decreasing about 60t that is caused by the moving of molten metal. It is not necessary to invest an extra facilities in order to discharge the gas generated from a degasing process by using an agitator. The working environment can be improved by the hospitable air in the factory because the molten metal is almost not exposed in the interior of the area.

• 한국식품영양학회지
• /
• 제32권4호
• /
• pp.294-303
• /
• 2019

To extend the shelf-life of chicken breast meat, samples were treated with gel-packs containing slow-released $ClO_2$ gas at 7-15 ppm for 8 days at $4^{\circ}C$. And the changes in lipid oxidation and taste compounds of the samples were investigated. TBARS value of the chicken breast was slightly increased during storage. TBARS value of gas treatments was similar to the control during storage. There were 14 fatty acids in the chicken breast. And there was no change in the fatty acid composition during storage, and there was no significant difference between the control and gas treatments. The content of free amino acids was gradually increased during storage. The content of free amino acids were not significantly different between the control and gas treatments during storage. The content of GMP in the control and gas treatments were decreased during storage. However, gas treatments showed slightly higher content than that of control. AMP was not significantly different between the control and gas treatments. IMP gradually decreased during storage and the content of inosine and hypoxanthine was increased. IMP, inosine and hypoxanthine contents of gas treatment were similar to control, but the control tended to change more rapidly than those of gas treatments.

• 한국안전학회지
• /
• 제9권3호
• /
• pp.53-59
• /
• 1994

Hydrogen(H$_2$) is used in the semiconductor industries, and some oxidizing gases such as fluoride(F$_2$) and chlorine trifluoride(CIF$_3$) are also used. As F$_2$and CIF$_3$are highly oxidizing gases, it were supposed to react vigorously with H$_2$. In this study, the flammability limit of F$_2$/$H_2$/Ar and CIF$_3$/$H_2$/Ar mixtures were investigated experimentally. As a result, it was found that the diluted F$_2$gas could be spontaneously ignited as compared to CIF$_3$mixture gas while being mixed with the diluted H$_2$gas. However, CIF$_3$diluted gas was not able to ignite spontaneously except for an electric spark. And the combustion characteristics and reaction kinetics were shown at the different diluted gases by the flammability diagram analyses between the F$_2$/$H_2$/Ar and CIF$_3$/$H_2$/Ar.

• 대한기계학회논문집B
• /
• 제26권10호
• /
• pp.1406-1418
• /
• 2002

The direct simulation Monte Carlo(DSMC) method is employed to calculate the etch rate on Al wafer. The etchant is assumed to be Cl$_2$. The etching process of an Al wafer in a helicon plasma etcher is examined by simulating molecular collisions of reactant and product. The flow field inside a plasma etch reactor is also simulated by the DSMC method fur a chlorine feed gas flow. The surface reaction on the Al wafer is simply modelled by one-step reaction: 3C1$_2$+2Allongrightarrow1 2AIC1$_3$. The gas flow inside the reactor is compared for six different nozzle locations. It is found that the flow field inside the reactor is affected by the nozzle locations. The Cl$_2$ number density on the wafer decreases as the nozzle location moves toward the side of the reactor. Also, the present numerical results show that the nozzle location 1, which is at the top of the reactor chamber, produces a higher etch rate.

• 한국전자통신학회논문지
• /
• 제18권1호
• /
• pp.195-204
• /
• 2023

드론의 배터리 시스템은 리튬이온 또는 리튬폴리머 배터리를 사용하는데, 드론 사용 후 폐기 과정에서 화재 원인은 폐기되는 배터리에서 발생하는 가연성 가스인 것으로 알려졌다. 폐기공정에 들어간 배터리는 대부분 산소가 발생했지만 미량의 가연성 가스도 발생했고, 처리에 사용된 장비에서도 다량의 염소 이온과 황산염이 검출됐다. 이를 조기에 감지하는 시스템이 구성된다면 폐기 배터리로 인한 사고 위험을 줄일 수 있을 것이다.