• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.2 s.344
• /
• pp.44-48
• /
• 2006

This study is intended to provide guidelines in establishing courses on domestic developments of chipless tags by observing status of domestic and foreign RFID tag providers, along with status of foreign manufacturers in RFID chipless tags, which is highly interested in overseas as well astechnical status of major providers. This paper introduces methods of data writing to tags, reading and decoding the data. and characteristics of tags manufactured by Inkode and RFSAW, products has been researched.

• Journal of electromagnetic engineering and science
• /
• v.17 no.3
• /
• pp.159-164
• /
• 2017

This article proposes a design of chipless RFID tag with dipole array structure that is fully printable using conductive ink. The proposed tags encode data based on spectral signature modulations. The reading range is considerably increased (2 m) while maintaining low transmission power (1 mW). Several prototype chipless RFID tags were fabricated and measured in the SHF and UHF bands. The proposed dipole array structure enhances the antenna gain of the passive tags and contributes to overcoming the low conductivity of conductive ink. In order to verify the utility of our proposal, the tags are manufactured on paper, using conductive ink, for the purpose of economic mass production.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.530-535
• /
• 2021

In this paper, the design method for a chipless RFID tag using ELC resonators is proposed. A four-bit chipless RFID tag is designed in a two by two array configuration using three ELC resonators with different resonant peak frequencies and one compact IDC resonator. The resonant peak frequency of the bistatic RCS for the IDC resonator is 3.125 GHz, whereas those of the three ELC resonators are adjusted to be at 4.225 GHz, 4.825 GHz, and 5.240 GHz, respectively, by using the gap between the capacitor-shaped strips in the ELC resonator. The spacing between the resonators is 1 mm. Proposed four-bit tag is fabricated on an RF-301 substrate with dimensions of 50 mm×20 mm and a thickness of 0.8 mm. It is observed from experiment results that the resonant peak frequencies of the fabricated four-bit chipless RFID tag are 3.290 GHz, 4.295 GHz, 4.835 GHz, and 5.230 GHz, respectively, which is similar to the simulation results with errors in the range between -2.3% and 0.2%.

• Journal of Advanced Navigation Technology
• /
• v.25 no.1
• /
• pp.90-95
• /
• 2021

In this paper, the design method for a high-sensitivity compact resonator for chipless RFID tags is proposed. Proposed high-sensitivity compact resonator uses an interdigital-capacitor structure instead of a capacitor-shaped strip structure in a conventional ELC resonator. The length of the electrode plate of the IDC structure is longer than that of the conventional capacitor-shaped structure, resulting in a larger equivalent capacitance of the resonator. This can lower the resonant peak frequency of the RCS characteristic. Two resonators with the same length of the square loop and the width of the strip are fabricated on an RF-301 substrate with a thickness of 0.8 mm. The experiment results show that the resonant peak frequency and value of the bistatic RCS for the ELC resonator were 4.305 GHz and -30.39 dBsm, whereas those of the proposed IDC resonator were 3.295 GHz and -36.91 dBsm. Therefore, the size of the resonator is reduced by 23.5% based on the measured resonant peak frequency of the RCS characteristic.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.247-252
• /
• 2013

In this paper, a microwave tag system of a frequency-scanning type is proposed with multi-resonators using defected ground structures. While a conventional chip-based RFID stores time-sequential codes, the proposed type achieves pure passive tags by using multi-resonant bits over a frequency range. Moreover, the resonators of the spiral defected ground structures implemented on the back side of transmission lines have advantages of the excellent bandstop characteristics as well as the bit-error avoidance by the re-radiation on normal resonators. The proposed microwave tag is designed with UWB antennas at 3~7 GHz. From the experimental results in an anechoic chamber, it has been verified of the excellent recognitions for various 5-bits identification codes.