• Journal of the Korean Wood Science and Technology
• /
• v.43 no.3
• /
• pp.400-409
• /
• 2015

This study examined the plant growth and development characteristics of leafy vegetables on the hydroponic substrates of waste wood chips, radiate pine chips, and mat type of waste wood chips. The bulk density of waste wood chips and radiata pine chips were $0.2g/cm^3$ and $0.16g/cm^3$, respectively. The moisture retention properties of both the radiata pine chips and waste wood chips were found to be similar but not better than those of the control rock wool and coco peat hydroponic substrates. The moisture retention property of the mat type was found to be the lowest. The chemical analysis of waste wood hydroponic substrates (w/v) was as follows.; The pH was 6.59, electric conductivity was 6.76 dS/m, total nitrogen content was 0.5%, C/N ratio was 113%, phosphorus was 10.1 ppm, potassium was 77 ppm, calcium was 531 ppm, magnesium was 49 ppm, and sodium was 96 ppm. The results from the radiata pine chemical analysis showed that it had a pH of 5.29, electric conductivity of 4.49 dS/m, total nitrogen content of 0.32%, C/N ratio of 180%, phosphorus of 6.4 ppm, potassium of 83 ppm, calcium of 97 ppm, magnesium of 29 ppm, and sodium of 59 ppm. Except for the plants grown in mat type, the developmental characteristics of the plants grown in rock wool and coco peat hydroponic substrates were similar. Based on the results of the experiment, waste wood resources may possibly be used as an organic solid medium in place of the existing rock wool and coco peat medium.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.12
• /
• pp.6-13
• /
• 2009

For X-band phased array systems, a power amplifier, a 6-bit phase shifter, a 6-bit digital attenuator, and a SPDT transmit/receive (T/R) switch are fabricated and measured. All circuits are demonstrated by using CMOS 0.18 um technology. The power amplifier has 2-stage differential and cascade structures. It provides 1-dB gain-compressed output power ($P_{1dB}$) of 20 dBm and power-added-efficiency (PAE) of 19 % at 8-11 GHz frequencies. The 6-bit phase shifter utilizes embedded switched filter structure which consists of nMOS transistors as a switch and meandered microstrip lines for desired inductances. It has $360^{\circ}$ phase-control range and $5.6^{\circ}$ phase resolution. At 8-11 GHz frequencies, it has RMS phase and amplitude errors are below $5^{\circ}$ and 0.8 dB, and insertion loss of $-15.7\;{\pm}\;1,1\;dB$. The 6-bit digital attenuator is comprised of embedded switched Pi-and T-type attenuators resistive networks and nMOS switches and employes compensation circuits for low insertion phase variation. It has max. attenuation of 31.5 dB and 0.5 dB amplitude resolution. Its RMS amplitude and phase errors are below 0.4 dB and $2^{\circ}$ at 8-11 GHz frequencies, and insertion loss is $-10.5\;{\pm}\;0.8\;dB$. The SPDT T/R switch has series and shunt transistor pairs on transmit and receive path, and only one inductance to reduce chip area. It shows insertion loss of -1.5 dB, return loss below -15 dB, and isolation about -30 dB. The fabricated chip areas are $1.28\;mm^2$, $1.9mm^2$, $0.34\;mm^2$, $0.02mm^2$, respectively.

• The Korean Journal of Air & Space Law and Policy
• /
• v.32 no.2
• /
• pp.155-188
• /
• 2017

On the one hand, the 4th Industrial Revolution provides a positive opportunity to build a new civilization paradigm for mankind. However, on the other hand, due to the 4th Industrial Revolution, artificial intelligence such as 'Goggle Alpha Go' revolutionized and even the human ability was replaced with a 'Silicon Chip' as the opportunity to communicate decreases, the existence of human beings is weakened. And there is a growing concern that the number of violent crimes, such as psychopath, which hunts humans as games, will increase. Moreover, recent international terrorism is being developed in a form similar to 'Psychopathic Violent-Crime' that indiscriminately attacks innocent people. So, the probability that terrorist organizations abuse the positive effects provided by the Fourth Industrial Revolution as means of terrorism is increasing. Therefore, the paradigm of aviation terrorism is expected to change in a way that attacks airport facilities and users rather than aircraft. Because airport facilities are crowded, and psychopathic terrorists are easily accessible. From this point of view, our counter terrorism system of aviation has many weak points in various aspects such as: (1) limitations of counter-terrorism center (2) inefficient on-site command and control system (3) separated organization for aviation security consultation (4) dispersed information collection function in government (5) vulnerable to cyber attack (6) lack of international cooperation network for aviation terrorism. Consequently, it is necessary to improve the domestic counter terrorism system of aviation so as to preemptively respond to the international terrorism. This study propose the following measures to improve the aviation security system by (1) create 'Aviation Special Judicial Police' (2) revise the anti-terrorism law and aviation security law (3) Strengthening the ability respond to terrorism in cyberspace (4) building an international cooperation network for aviation terrorism.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.6
• /
• pp.1210-1230
• /
• 1997

In this paper, we suggest an architecture of DS/CDMA tranceiver composed of one pilot channel used as reference and multiple traffic channels. The pilot channel-an unmodulated PN code-is used as the reference signal for synchronization of PN code and data demondulation. The coherent demodulation architecture is also exploited for the reverse link as well as for the forward link. Here are the characteristics of the suggested DS/CDMA system. First, we suggest an interlaced quadrature spreading(IQS) method. In this method, the PN coe for I-phase 1st channel is used for Q-phase 2nd channels and the PN code for Q-phase 1st channel is used for I-phase 2nd channel, and so on-which is quite different from the eisting spreading schemes of DS/CDMA systems, such as IS-95 digital CDMA cellular or W-CDMA for PCS. By doing IQS spreading, we can drastically reduce the zero crossing rate of the RF signals. Second, we introduce an adaptive threshold setting for the synchronization of PN code, an initial acquistion method that uses a single PN code generator and reduces the acquistion time by a half compared the existing ones, and exploit the state machines to reduce the reacquistion time Third, various kinds of functions, such as automatic frequency control(AFC), automatic level control(ALC), bit-error-rate(BER) estimator, and spectral shaping for reducing the adjacent channel interference, are introduced to improve the system performance. Fourth, we designed and implemented the DS/CDMA MODEM to be used for variable transmission rate applications-from 16Kbps to 1.024Mbps. We developed and confirmed the DS/CDMA MODEM architecture through mathematical analysis and various kind of simulations. The ASIC design was done using VHDL coding and synthesis. To cope with several different kinds of applications, we developed transmitter and receiver ASICs separately. While a single transmitter or receiver ASC contains three channels (one for the pilot and the others for the traffic channels), by combining several transmitter ASICs, we can expand the number of channels up to 64. The ASICs are now under use for implementing a line-of-sight (LOS) radio equipment.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.12
• /
• pp.654-664
• /
• 2000

Thin films of ZnO are deposited by using an RF magnetron sputtering with varying the substrate temperature(RT~39$0^{\circ}C$) and RF power(50~250W). Cu-doped ZnO(denoted by ZnO:Cu) films have also been prepared by co-spputtering of a ZnO target on which some Cu-chips are attached. Different substrate materials, such as Si, $SiO_{2}/Si$, sapphire, DLC/Si, and poly-diamond/Si, are employed to compare the c-axial growth features of deposited ZnO films. Texture coefficient(TC) values for the (002)-preferential growth are estimated from the XRD spectra of deposited films. Optimal ranges of RF powers and substrate temperatures for obtaining high TC values are determined. Effects of Cu-doping conditions, such as relative Cu-chip sputtering areas, $O_{2}/(Ar+O_{2})$ mixing ratios, and reactor pressures, on TC values, electrical resistivities, and relative Cu-compositions of deposited ZnO:Cu films have been systematically investigated. XPS study shows that the relative densities of metallic $Cu(Cu^{0})$ atoms and $CuO(Cu^{2+})$-phases within deposited films may play an important role of determining their electrical resistivities. It should be noted from the experimental results that highly resistive(> $10^{10}{\Omega}cm$ ZnO films with high TC values(> 80%) can be achieved by Cu-doping. SAW devices with ZnO(or Zn):Cu)/IDT/$SiO_{2}$/Si configuration are also fabricated to estimate the effective electric-mechanical coupling coefficient($k_{eff}^{2}$) and the insertion loss. It is observed that the devices using the Cu-doped ZnO films have a higher $k_{eff}^{2}$ and a lower insertion loss, compared with those using the undoped films.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.6
• /
• pp.784-790
• /
• 2018

Objective: The genetic effects of an individual on the phenotypes of its social partners, such as its pen mates, are known as social genetic effects. This study aims to identify the candidate genes for social (pen-mates') average daily gain (ADG) in pigs by using the genome-wide association approach. Methods: Social ADG (sADG) was the average ADG of unrelated pen-mates (strangers). We used the phenotype data (16,802 records) after correcting for batch (week), sex, pen, number of strangers (1 to 7 pigs) in the pen, full-sib rate (0% to 80%) within pen, and age at the end of the test. A total of 1,041 pigs from Landrace breeds were genotyped using the Illumina PorcineSNP60 v2 BeadChip panel, which comprised 61,565 single nucleotide polymorphism (SNP) markers. After quality control, 909 individuals and 39,837 markers remained for sADG in genome-wide association study. Results: We detected five new SNPs, all on chromosome 6, which have not been associated with social ADG or other growth traits to date. One SNP was inside the prostaglandin $F2{\alpha}$ receptor (PTGFR) gene, another SNP was located 22 kb upstream of gene interferon-induced protein 44 (IFI44), and the last three SNPs were between 161 kb and 191 kb upstream of the EGF latrophilin and seven transmembrane domain-containing protein 1 (ELTD1) gene. PTGFR, IFI44, and ELTD1 were never associated with social interaction and social genetic effects in any of the previous studies. Conclusion: The identification of several genomic regions, and candidate genes associated with social genetic effects reported here, could contribute to a better understanding of the genetic basis of interaction traits for ADG. In conclusion, we suggest that the PTGFR, IFI44, and ELTD1 may be used as a molecular marker for sADG, although their functional effect was not defined yet. Thus, it will be of interest to execute association studies in those genes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.5
• /
• pp.307-312
• /
• 2018

Liquid phases in ZnO varistors cause more complex phase development and microstructure, which makes the control of electrical properties and reliability more difficult. Therefore, we have investigated 2 mol% $CaCO_3$ doped $ZnO-Co_3O_4-Cr_2O_3-La_2O_3$ (ZCCLCa) bulk ceramics as one of the compositions without liquid phase sintering additive. The results were as follows: when $CaCO_3$ is added to ZCCLCa ($644{\Omega}cm$) acting as a simple ohmic resistor, CaO does not form a secondary phase with ZnO but is mostly distributed in the grain boundary and has excellent varistor characteristics (high nonlinear coefficient ${\alpha}=78$, low leakage current of $0.06{\mu}A/cm^2$, and high insulation resistance of $1{\times}10^{11}{\Omega}cm$). The main defects $Zn_i^{{\cdot}{\cdot}}$ (AS: 0.16 eV, IS & MS: 0.20 eV) and $V_o^{\bullet}$ (AS: 0.29 eV, IS & MS: 0.37 eV) were found, and the grain boundaries had 1.1 eV with electrically single grain boundary. The resistance of each defect and grain boundary decreases exponentially with increasing the measurement temperature. However, the capacitance (0.2 nF) of the grain boundary was ~1/10 lower than that of the two defects (~3.8 nF, ~2.2 nF) and showed a tendency to decrease as the measurement temperature increased. Therefore, ZCCLCa varistors have high sintering temperature of $1,200^{\circ}C$ due to lack of liquid phase additives, but excellent varistor characteristics are exhibited, which means ZCCLCa is a good candidate for realizing chip type or disc type commercial varistor products with excellent performance.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.1
• /
• pp.97-102
• /
• 2015

The long line fishing machine is combined with motor and two disc rollers has used on the small size fishing-boat under 1 ton located in near Jeollanam-do seaside. The long line fishing motor is controlled only one direction because the fishing line is loaded heavily at pulling up. On this paper we made the long line fishing 400W power motor controller which it was usually applied under 1 ton fishing boat, and designed the controller using PWM chip, Half bridge driver and MOSFET for one direction motor control. Furthermore some user convenience devices were added like battery indicator and safety protection circuit for battery overdischarge and battery source wire mismatch connection. So we protected the battery from overdicharging when the battery voltage was below 11.5V and fishermen didn't need to worry about source lines misconnection anymore. We confirmed the test version of controller was the good working condition at land and sea.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.128-135
• /
• 2013

This paper presents a high dimming ratio Power-LED driver IC with high power which is capable of controlling LEDs. In order to accomplish a high dimming ratio LED driver, the preloading inductor current methodology is proposed for the power stage of the proposed method to achieve the fast transient response time during the Power-LED load switching. The information containing the current flowing on the LEDs can be utilized to predict the amount of the current on the inductor. The minimum LED current rising time of existing high dimming ratio Power-LED driver is limited by $3{\mu}s$, however that of the proposed high dimming ratio Power-LED driver is reduced about 1/10. The LED driver is implemented with 0.35um 60V BCDMOS 2-poly 4-metal process. The measurement results show that the proposed LED driver system features the minimum rising time as small as 240ns at the dimming frequency of 1KHz with a 12V of input voltage, nine white LEDs and 353mA of LED current. The LED rising time and power conversion efficiency of the chip are measured to be 240ns and 93.72%, respectively.

• Korean Journal of Environmental Agriculture
• /
• v.18 no.4
• /
• pp.321-326
• /
• 1999

This study was performed to evaluate the quality of produced compost and to analyse the change of a component during the reduction compost according to the input volume. The volume of pilot scale used in this study was about 300㎥. The pile of 2m width, 20m length and 1.2m height was constructed. Woodchip was used as bulking agent to enhance pore volume of composting bay and to control water content of food waste in starting time. Food waste was turned using a mechanical tumer twice a day. The result are as follows : In these cases of input volume of $2m^3$ and $3.5m^3$, temperature of composting pile was maintained over $60^{\circ}C$ and water content was 43.6% and 47.2%, respectively. It was proved that microorganisms activity was maintained high in each input volume. After operation of step 1 and step 2, pH and organic matter in the final compost were 6.2, 6.6 and 84.3%, 79.6%, respectively. Cation concentration such as $K_2O,$ CaO and NaCl was accumulated in the compost during the composting period. NaCl concentration in the final compost was 4.62%, 4.92%, respectively. Hence, If was recommended that this compost should be applied to others expect agricultural area or mixed with a low concentration other compost. In the steps 1, input volume of $2m^3$, heavy metal concentration of Pb, Cu, Cr, Ni. Cd were 37.82㎎/㎏, 56.87㎎/㎏, 9.8㎎/㎏. 22.21㎎/㎏ and 3.69㎎/㎏, and 44.55㎎/㎏, 95.54㎎/㎏, 12.22㎎/㎏, 24.94㎎/㎏, and 3.86㎎/㎏ in the step 2.