• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.22-27
• /
• 2004

This experimental investigation was conducted to examine the seismic performance of reinforced concrete bridge columns. The columns were subjected to a constant axial load and a cyclic horizontal load-inducing reversed bending moment. The variables studied in this research are the volumetric ratio of transverse reinforcement (ps = 0.96, 1.44 per cent) and axial load ratio (0.05, 0.1, 0.2 P/Po) and strength $(350kgf/cm^2,\;600kgf/cm^2)$. Test results show that bridge columns with 50 per cent higher amounts of transverse reinforcement than that required by seismic provisions of ACI 318-02 showed ductile behaviour. For bridge columns with axial load ratio(P/Po) less than 0.2, the ratio of Mmax over Mad, nominal moment capacity predicted by ACI 318-02 provisions, is consistently greater than 1 with approximately a 20 percent margin of safty.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1246-1252
• /
• 2002

Ultrafine grained (UFG) low carbon (0.15 wt.% C) steel produced by equal channel angula. pressing (ECAP) was tested for investigating the effect of load ratio on the fatigue crack growth rate. Fatigue crack growth resistance and threshold of UFG steel were lower than that of asreceived coarse grained steel. It was attributed to the less tortuous crack path. The UFG steel exhibited slightly higher crack growth rates and a lower △Kth with an increase of R ratio. The R ratio effect on crack growth rates and △Kth was basically indistinguishable at lower load ratio (R >0.3), compared to other alloys, which indicates that contribution of the crack closure vanishes. The crack growth rate curve for UFG steel exhibited a longer linear extension to the lower growth rate regime than that for the coarse grained as-received steel.

• Structural Engineering and Mechanics
• /
• v.52 no.4
• /
• pp.739-753
• /
• 2014

There have been many packages that can be employed to analyze plane frames. However, because most structural analysis packages suffer from closeness of system, it is very difficult to integrate it with an optimization package. To overcome the difficulty, we proposed a possible alternative, DAMDO, which integrate Design, Analysis, Modeling, Definition, and Optimization phases into an integrative environment. The DAMDO methodology employs neural networks to integrate structural analysis package and optimization package so as not to need directly to integrate these two packages. The key problem of the DAMDO approach is how to generate a set of reasonable random designs in the first phase. According to the characteristics of optimized plane frames, we proposed the ratio variable approach to generate them. The empirical results show that the ratio variable approach can greatly improve the accuracy of the neural networks, and the plane frame optimization problems can be solved by the DAMDO methodology.

• KIEAE Journal
• /
• v.6 no.2
• /
• pp.35-42
• /
• 2006

This study is to investigate the possibility of a quantitative analysis on sunshine right in apartment houses with a new evaluation index of shading area ratio(SAR) which represents seasonal average value of shaded portion of a window during definite period. SAR values of each apartment houses in a prototype building was calculated depending on apartment building arrangement types and orientations. Since the new method proposed in this research is able to measure the sunshine possibility of the each house in detail, which is more precise and descriptive than the existing method of sunshine judgment standard based on the sunshine hours only at winter solstice, it can be appropriately utilized as a highly qualified sunshine right judgment measures in apartment buildings.

• Journal of the Korean Chemical Society
• /
• v.13 no.3
• /
• pp.199-204
• /
• 1969

The distribution rate of 4f and 5f series elements in chelate and ion association extraction system was studied. Clear difference between lighter and heavier part of 4f series are observed. Trivalent Am and Cm were appeared to be grouped into the lighter part of 4f series. And also the variation of distribution ratio according to the varied temperature was studied. The variation modes of distribution ratio are different according to the extraction system. Atomic number dependence in the chelate extraction system was observed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.617-620
• /
• 2006

The EVA polymer is used as a modifier in the repair mortar, which contains various admixtures and mineral admixtures. It has been reported that the effect of polymer in cement mortar by the cement-polymer ratio only, but effect of admixtures over the polymer mortar was unknown. In this study, the fresh and mechanical properties of polymer cement mortar influenced by the range of silica fume ratio were investigated. It was found that with increasing the ratio of silica fume, mechanical properties(compressive strength, flexural strength, adhesive strength) of repair mortar is improved and drying shrinkage is increased.

• The korean journal of orthodontics
• /
• v.49 no.1
• /
• pp.3-11
• /
• 2019

Objective: The purpose of this study was to investigate the influence of heritability on the craniofacial soft tissue cephalometric characteristics of monozygotic (MZ) twins, dizygotic (DZ) twins, and their siblings (SIB). Methods: The samples comprised Korean adult twins and their siblings (mean age, 39.8 years; MZ group, n = 36 pairs; DZ group, n = 13 pairs of the same gender; and SIB group, n = 26 pairs of the same gender). Thirty cephalometric variables were measured to characterize facial profile, facial height, soft-tissue thickness, and projection of nose and lip. Falconer's method was used to calculate heritability (low heritability, $h^2$ < 0.2; high heritability, $h^2$ > 0.9). After principal components analysis (PCA) was performed to extract the models, we calculated the intraclass correlation coefficient (ICC) value and heritability of each component. Results: The MZ group exhibited higher ICC values for all cephalometric variables than DZ and SIB groups. Among cephalometric variables, the highest ${h^2}_{(MZ-DZ)}$ and ${h^2}_{(MZ-SIB)}$ values were observed for the nasolabial angle (NLA, 1.544 and 2.036), chin angle (1.342 and 1.112), soft tissue chin thickness (2.872 and 1.226), and upper lip thickness ratio (1.592 and 1.026). PCA derived eight components with 84.5% of a cumulative explanation. The components that exhibited higher values of ${h^2}_{(MZ-DZ)}$ and ${h^2}_{(MZ-SIB)}$ were PCA2, which includes facial convexity, NLA, and nose projection (1.026 and 0.972), and PCA7, which includes chin angle and soft tissue chin thickness (2.107 and 1.169). Conclusions: The nose and soft tissue chin were more influenced by genetic factors than other soft tissues.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1591-1594
• /
• 2006

In this work, we fabricated efficient white organic light emitting device (WOLED) by the stack of complementary fluorescent dye-doped layers, Effect of dye-doping ratio and thickness of each layers on WOLED efficiency and emission spectrum was investigated. Moreover, out-coupling efficiency enhancement using microlens array was analyzed for bottom and top-emitting device architecture, leading to higher light extraction properties.

• Journal of the Korean Chemical Society
• /
• v.14 no.3
• /
• pp.257-261
• /
• 1970

Some factors such as the weight ratio, reaction time and temperature for the separation of rare earth elements from monazite are studied. The influence of the inorganic phosphate for the leaching is also studied.

• IE interfaces
• /
• v.16 no.spc
• /
• pp.132-137
• /
• 2003

We consider scheduling jobs on multipurpose machines where jobs can be processed by a subset of the machines operated in parallel with the objective of minimizing makespan. We apply LPT(Longest Processing Time first) algorithm and prove that its posterior worst-case performance ratio is at most $log_24m/(1+{\lambda})$, where \lambda is the number of machines eligible for processing the job with the latest completion time. In general, LPT is shown to always find a schedule with makespan at most $log_24m/3$ times optimum.