• Membrane Journal
• /
• v.5 no.1
• /
• pp.35-43
• /
• 1995

For several years lots of attempts have been made to establish the liquid membrane-based techniques for separations of gas mixtures especially containing carbon dioxide. A more effective system to separate $CO_{2}$ from flue gases, a circulatory hollow-fiber membrane absorber(HFMA) consisting of absorption and desorption modules with vacuum mode, has been considered in this study. Gas-liquid mass transfer has been modeled on a membrane module with non-wetted hollow-fibers in the laminar flow regime. The influence of an absorbent flow rate on the separation performance of the circulatory HFMA can be predicted quantitatively by obtaining the $CO_{2}$ concentration profile in a tube side. The system of $CO_{2}/N_{2}$ binary gas mixture has been studied using pure water as an(inert) absorbent. As the absorbent flow rate is increased, the permeation flux(i.e., defined as permeation rate/membrane contact area) also increases. The enhanced selectivity compared to the previous results, on the other hand, shows the decreasing behavior. It has been found obviously that the permeation flux depends on the variations of pressure in gas phase of desorption module. From an accurate comparison with the results of conventional flat sheet membrane module, the advantageous permeability of this circulatory HFMA can be clearly ascertained as expected. Our efforts to the theoretical model will provide the basic analysis on the circulatory HFMA technique for a better design and process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.77-77
• /
• 1998

Present silicon dioxide (SiOz) 떠m as intennetal dielectridIMD) layers will result in high parasitic c capacitance and crosstalk interference in 비gh density devices. Low dielectric materials such as f f1uorina뼈 silicon oxide(SiOF) and f1uoropolymer IMD layers have been tried to s이ve this problem. I In the SiOF ftlm, as fluorine concentration increases the dielectric constant of t뼈 film decreases but i it becomes unstable and wa않r absorptivity increases. The dielectric constant above 3.0 is obtain어 i in these ftlms. Fluoropolymers such as polyte$\sigma$따luoroethylene(PTFE) are known as low dielectric c constant (>2.0) materials. However, their $\alpha$)Or thermal stability and low adhesive fa$\pi$e have h hindered 야1리ru뚱 as IMD ma따"ials. 1 The concept of a plasma processing a찌Jaratus with 비gh density plasma at low pressure has r received much attention for deposition because films made in these plasma reactors have many a advantages such as go여 film quality and gap filling profile. High ion flux with low ion energy in m the high density plasma make the low contamination and go어 $\sigma$'Oss피lked ftlm. Especially the h helicon plasma reactor have attractive features for ftlm deposition 야~au똥 of i앙 high density plasma p production compared with other conventional type plasma soun:es. I In this pa야Jr, we present the results on the low dielectric constant fluorocarbonated-SiOF film d밑JOsited on p-Si(loo) 5 inch silicon substrates with 00% of 0dFTES gas mixture and 20% of Ar g gas in a helicon plasma reactor. High density 띠asma is generated in the conventional helicon p plasma soun:e with Nagoya type ill antenna, 5-15 MHz and 1 kW RF power, 700 Gauss of m magnetic field, and 1.5 mTorr of pressure. The electron density and temperature of the 0dFTES d discharge are measUI벼 by Langmuir probe. The relative density of radicals are measured by optic허 e emission spe따'Oscopy(OES). Chemical bonding structure 3I피 atomic concentration 따'C characterized u using fourier transform infrared(FTIR) s야3띠"Oscopy and X -ray photonelectron spl:’따'Oscopy (XPS). D Dielectric constant is measured using a metal insulator semiconductor (MIS;AVO.4 $\mu$ m thick f fIlmlp-SD s$\sigma$ucture. A chemical stoichiome$\sigma$y of 야Ie fluorocarbina$textsc{k}$영-SiOF film 따~si야영 at room temperature, which t the flow rate of Oz and FTES gas is Isccm and 6sccm, res야~tvely, is form려 야Ie SiouFo.36Co.14. A d dielec$\sigma$ic constant of this fIlm is 2.8, but the s$\alpha$'!Cimen at annealed 5OOt: is obtain려 3.24, and the s stepcoverage in the 0.4 $\mu$ m and 0.5 $\mu$ m pattern 킹'C above 92% and 91% without void, res야~tively. res야~tively.

• Food Science of Animal Resources
• /
• v.25 no.3
• /
• pp.285-294
• /
• 2005

The objective of this study was to evaluate the physico-chemical properties and flavor compounds of sausages with various levels and molecular weight (MWs) of chitosans, during storage at $4^{\circ}C$. Various MWs (Low: 1.5 kDa; Medium: $30{\sim}50$ kDa; High: 200 kDa) and two levels (0.3 and $0.6\%$) of chiosans were dissolved and measured the viscosity at $4^{\circ}C$, pH values were not affected (p>0.05) by either MWs or levels of chitosans. The addition or high MWs or chitosan into the pork salt soluble protein (SSP) increased the viscosity, whereas no differences were observed in low and medium MWs of chitosan. Textural profile analysis (TPA) was affected by the addition of medium or high MWs of chitosan. As a result, the addition of medium of chitosan increased the hardness, gumminess, chewiness, cohesiveness and springiness values, whereas increased level of chitosan didn't affect TPA values, except few cases. Approximately twenty-nine flavor compounds were identified in the low-fat and regular-fat sausages, however the addition of chitosans didn't impair the flavor composition of the sausages, These results indicated that the addition of chitosans didn't affect the flavor profiles, but affected the textural properties in the sausages, especially MWs higher than 30 kDa.

• Food Science of Animal Resources
• /
• v.26 no.1
• /
• pp.98-105
• /
• 2006

This study was performed to investigate the product characteristics of meat products sold in Korean markets and determine if these products meet the comsumer demands. The total nineteen meat produce were evaluated the physico-chemical, textural properties, and microbial counts of total bacteria and Enterobacteriaceae. pH values were ranged from 5.46 to 6.69, moisture $47.6{\sim}65.3%,\;fat\;14.2{\sim}34.7%,\;and\;9{\sim}20%$ and the pH values of ham products were higher than those of sausages. Purge loss(%) and expressible moisture(%) were ranged $2.40{\sim}7.44\;and\;6.10{\sim}21.2%$ respectively. Varied hunter color values (Lightness $59.6{\sim}75.7$, Redness $11.6{\sim}21.1$, Yellowness $2.30{\sim}l1.4$) were observed. Texture profile analysis values were observed and Frank A sausages made with chicken had highest fracturability, hardness and springiness, whereas loin ham and beershinken had highest cohesiveness, gumminess and chewiness. Most meat products had the total microbial counts of less than 3 log CFU/g and Enterbacteriaceae were not detected (< 2 log CFU/g) in this study. These data suggested that the meat products sold in Korean market were various and relatively safe. In addition, well-being meat products, such as low-fat, salt and containing functional ingredient, should be developed to meet the consumer needs these days.

• Fire Science and Engineering
• /
• v.13 no.1
• /
• pp.37-47
• /
• 1999

The spreading fire of very small floating particles after they are ignited is fast and t therefore dangerous. The research on this area has been limited to experiments and global simulations which treat them as dusts or gaseous fuel with certain concentration well m mixed with air. This research attempted micro-scale analysis of ignition of those particles modeling them as liquid droplets. For the beginning, the in-line array of fuel droplets is modeled by two-dimensional, unsteady conservation equations for mass, momentum, energy and species transport in the gas phase and an unsteady energy equation in the liquid phase. They are solved numerically in a generalized non-orthogonal coordinate. The single step chemical reaction with reaction rate controlled by Arrhenius’ law is assumed to a assess chemical reaction numerically. The calculated results show the variation of temperature and the concentration profile with time during evaporation and ignition process. Surrounding oxygen starts to mix with evaporating fuel vapor from the droplet. When the ignition condition is met, the exothermic reactions of the premixed gas initiate a and burn intensely. The maximum temperature position gradually approaches the droplet surface and maximum temperature increases rapidly following the ignition. The fuel and oxygen concentration distributions have minimum points near the peak temperature position. Therefore the moment of ignition seems to have a premixed-flame aspect. After this very short transient period minimum points are observed in the oxygen and fuel d distributions and the diffusion flame is established. The distance between droplets is an important parameter. Starting from far-away apart, when the distance between droplets decreases, the ignition-delay time decreases meaning faster ignition. When they are close and after the ignition, the maximum temperature moves away from the center line of the in-line array. It means that the oxygen at the center line is consumed rapidly and further supply is blocked by the flame. The study helped the understanding of the ignition of d droplet array and opened the possibility of further research.

• Applied Biological Chemistry
• /
• v.40 no.6
• /
• pp.472-477
• /
• 1997

The effects of roasting Cassia tora L. were investigated for proximate composition, color, volatile flavor profile, microbial growth and alcohol fermentation. While moisture, protein and fat contents decreased with increasing roasting temperature, fiber and ash contents increased. The L, a and b values of Cassia tora L. extracts decreased with increasing temperature, and only a small difference in total color difference$({\Delta}E)$ was observed. A little difference in major flavor components between raw and roasted treatment was found during roasting. Furfuryl alcohol, a major component of coffee flavor, was separated from Cassia tora L. extracts extracted with ethyl ether. The yeast growth was the highest on the water-extract of Cassia tora L. roasted at $160^{\circ}C$. With increased levels of water-extract at $160^{\circ}C$, S. cerevisiae grew rapidly for 24 hr incubation and the growth rate was higher than the unroasted control group. The growth rate of Bacillus subtilis was the highest in a treatment of 0.5% concentration. Little differences in ${\alpha}-amylase$ produced from Bacillus subtilis were observed among the treatment groups. The total alcohol content increased with increasing roasting temperature during alcohol fermentation.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.447-453
• /
• 2007

In this study, we fabricated recrystallized PLGA (rPLGA) particles using the vacuum drying method. In order to investigate an applicability of the rPLGA particles for controlled release system of 5-fluorouracil (5-FU) loaded PLGA wafer, we prepared three different wafers using; 1) untreated PLGA (uPLGA), 2) rPLGA, and 3) uPLGA and rPLGA (4 : 1, 1 : 1 or 1 : 4). The rPLGA particles were characterized using NMR, IR and GPC to compare with uPLGA particles. The surface and cross section morphology of the prepared wafers were observed by the scanning electron microscope. The release profile of the 5-FU loaded wafer was measured by HPLC. The 5-FU/rPLGA wafer released the incorporated 5-FU in a sustained manner with low initial burst compared to 5-FU/uPLGA. These results showed that the ratio of pure PLGA/recrystallized PLGA can affect the release behaviors.

• Polymer(Korea)
• /
• v.31 no.3
• /
• pp.201-205
• /
• 2007

Biodegradable polymers such as polylactide, polyglycolide and poly (lactide- co-glycolide) (PLGA) have been extensively investigated because of easily controlled drug release rate, completely degradable materials without the toxic by-product, and good biocompatibility. But, according to the bulk erosion property of PLGA in vitro test, it had the disadvantage that first-order release reduced releasing amount slowly after excessive initial burst. In this study we used PLGA powder obtained through recrystallization to revise bulk erosion property of PLGA. The PLGA used in this study was prepared by vacuum drying method and to estimate release profiles of BCNU loaded PLGA wafer. We also evaluated the release profile of drug with the water soluble additive. It was found that the drug loaded PLGA recrystallized by vacuum drying method exhibited the initial burst and the constant rate of drug release compared to that prepared by a conventional method.

• Journal of the Korean Chemical Society
• /
• v.18 no.4
• /
• pp.223-238
• /
• 1974

CNDO/2 MO theoretical studies and kinetic studies of halide exchange reactions for alkylchloroformates have been carried out in order to investigate structure-reactivity relationship of alkylchloroformates. From the result of energetics, it was concluded that the most stable configuration of alkylchloroformate is that in which alkyl group and chlorine are trans to each other, and that the hindered rotation about the bond between the carbonyl carbon and alkoxy-oxygen bond is attributed to the ${\pi}-$electron delocalization. It has been found that the large charge separation is due to -M effect of carbonyl and alkoxy oxygens and-I effect of chlorine. The order of rates in solvents studied was $(CH_3)_2 > CO > CH_3CN{\gg}MeOH.$$I^->Br^->Cl^-$ in protic solvent, and of Cl^->Br^- >I^-$ in dipolar aprotic solvents. Alkyl group contribution has the decreasing order of $CH_3-> C_2H-{\gg}i-C_3H_7-.$ The solvent effect has been interpreted on the basis of initial and final state contribution. A transition state model has been suggested, and it has been proposed that the most favorable mechanism is the addition-elimination. From the results of activation parameters and electronic properties, an energy profile has been proposed. Structural factors determining reactivities of alkylchloroformates have been shown to be charge, energy level of ${\alpha}^*LUMO$ to C-Cl bond and ${\alpha}^{\ast} $antibonding strength with respect to C-Cl bond in this MO. Charge and polarizability of nucleophile, and the interaction of these effects with solvent structures are also found to be important.

• Applied Biological Chemistry
• /
• v.41 no.7
• /
• pp.510-515
• /
• 1998

Effect of freezing of soybean and addition of mugwort on the flavor development and the changes of chemical compositions in Chungkookjang was investigated. The changes in the amount of amino-type N, the activities of ${\alpha}-amylase$ and protease, and the content of volatile compounds were determined during aging of Chungkookjang. During ripening, a little higher protease activity was detected in Chungkookjang made of frozen soybean than in that made of non-frozen soybean. However, the profile of ${\alpha}-amylase$ activity of Chungkookjang made of frozen soybean was very similar to that of Chungkookjang made of non-frozen soybean. The amount of amino-type N increased gradually with the ripening period and decreased after 21 days of ripening. The amount of amino-type N was slightly higher in Chungkookjang made of frozen soybean than in that made of non-frozen soybean. Addition of mugwort had little effect on the enzyme activities and the amino-type N content. The mugwort added in Chungkookjang reduced the production of cis-3-hexenol which is responsible for the unpleasant odor, and freezing of soybean enhanced the production of 2, 6-dimethyl pyrazine which is contribute to the taste. According to sensory evaluation, flavor was the highest after the 14 days of ripening and addition of mugwort increased significantly the flavor in both Chungkookjang prepared with frozen soybean and Chungkookjang with non-frozen soybean. However, the effect of freezing of soybean on the flavor was not significant.