• Economic and Environmental Geology
• /
• v.42 no.4
• /
• pp.357-366
• /
• 2009

Since weathering weakens the rock fabric and exaggerates any structural weakness, it affects mechanical properties as well as physical and chemical properties of rock. Weathering leads to a decrease in density, strength, friction angle and cohesion, and subsequently it affects negatively on the stability of rock slope. The purpose of the study is to investigate the changes of the rock slope stability caused by discontinuities which have different weathering grades. For that, the discontinuity samples which are divided into two different weathering grades are obtained from the field and tested their mechanical properties such as JCS, JRC and residual friction angle. In order to evaluate the effects on the stability of slope due to weathering, the deterministic analysis is carried out. That is, the factors of safety for planar failure are calculated for rock masses which have two different weathering grades, such as fresh and weathered rock mass. However, since the JRC and friction angle values are widely scattered and the deterministic analysis cannot consider the variation, the factors of safety cannot represent properly the stability of the rock slope. Therefore, the probabilistic analysis has been used to consider the scattered values. In the deterministic analysis, the factors of safety for the fresh discontinuity and weathered discontinuity are 1.25 and 1.0, respectively. The results indicate the fresh discontinuities are stable for planar failure and the weathered discontinuities are marginally stable. However, the probabilities of failure for the fresh discontinuity and weathered discontinuity are 25.6% and 45.9%, respectively. This shows that both discontinuities are analyzed as unstable in the probabilistic analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2971-2977
• /
• 2015

This study aimed to understand the changes in microbial community after algicide dosing to control the fish-killing dinoflagellate Cochlodinium polykrikoides in 10L microcosm. Based on our microcosm experiments, the algicidal activity for C. polykrikoides of yellow clay at the concentrations of 4g and 10g per 10 L was < 20%. At $0.8{\mu}M$ concentration of thiazolidinedione(TD49), the population of C. polykrikoides was controlled to be > 85%. In microbial community, a significant increase in heterotrophic bacterial (HB) abundance was observed at day 1 in the TD49 and yellow clay treatments including control. The HB remained high for 2 days and then gradually decreased. In contrast, the abundance of heterotrophic nanoflagellates (HNFs) increased significantly on days 3 and 5 in the TD49 treatments, indicating that the decline in HB was probably a result of predation by the high density of HNFs. In addition, fluctuations in the aloricate ciliate Uronema sp., which feed on bacteria, was clearly correlated with fluctuations in HB abundance, with a lag period of 1-3 days. Therefore, the short-term responses of the HNF and Uronema sp. may have been a result of the rapidly increasing of HB abundance, which is related to degradation of the dense C. polykrikoides bloom, particularly in the TD49 treatment. In addition, large aloricate ciliate Euplotes sp. was significantly increased after reproduction of HNFs and Uronema sp. Consequently, the algicide TD49 had positive effect on the microbial communities, which indicates that the microbial loop was temporarily enhanced in the microcosm by energy flow from HB through HNFs to ciliate.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.5 no.2
• /
• pp.101-109
• /
• 2003

The study area, Kwangneung Experiment Forest (KEF) is located on the west-central portion of Korean peninsula and belongs to a cool-temperate broadleaved forest Bone. At the old-growth deciduous forest near Soribong-peak (533.1 m) in KEF, we have established a 1 ha permanent plot ($100m{\times}100m$) and a flux tower, and the site was registered as a KLTER(Korean long-term ecological research network) and DK site of KoFlux. In this site, we made a stemmap of trees and analyzed forest stand structure and physical and chemical soil characteristics, and estimated carbon budgets by forest components (tree biomass, soils, litter and so on). Dominant tree species were Quercus serrata and Carpinus laxiflora, and accompanied by Q. aliena, Carpinus cordata, and so on. As a result of a field survey of the plot, density of the trees larger than 2 cm in DBH was 1,473 trees per ha, total biomass 261.2 tons/ha, and basal area $28.0m^2$/ha. Parent rock type is granite gneiss. Soil type is brown forest soil (alfisols in USDA system), and the depth is from 38 to 66 cm. Soil texture is loam or sandy loam, and its pH was f개m 4.2 to 5.0 in the surface layer, and from 4.8 to 5.2 in the subsurface layer. Seasonal changes in LAI were measured by hemispherical photography at the 1.2 m height, and the maximum was 3.65. And the spatial distributions of volumetric soil moisture contents and LAIs of the plot were measured. The carbon pool in living tree biomass including below ground biomass was 136 tons C/ha, and 5.6 tons C/ha is stored in the litter layer, and about 92.0 tons C/ha in the soil to the 30 cm in depth. Totally more than about 233.6 tons C/ha was stored in DK site. These ground survey and monitoring data will give some important parameters and validation data for the forest dynamics models or biogeochemical dynamics models to predict or interpolate spatially the changes in forest ecosystem structure and function.

• Journal of The Korean Association For Science Education
• /
• v.20 no.4
• /
• pp.527-541
• /
• 2000

The purpose of this study was to find out the characteristics of learning contents structure of K-12 science textbooks. The characteristics are related to 7 main concepts of matter properties; reaction rate, other reaction, density, solution, state change, absorption, and surface property. The contects are analyzed into 5 types of characteristics; type of concept extension, type of concept deepness, type of same level concept, type of confusion with other concepts, and type of concept interruption. First two types are positive content structures, but the others are negative structures. The findings are as follows. First, a lot of learning contents have the characteristic of 'type of same level concept'. There are few which have the characteristic of 'type of concept deepness'. Second, there are a lot of concepts related to 'properties of matter' which are not represented any more in middle and high school science textbooks. Those concepts are importantly taught in early childhood education and elementary school science. Most of the learning contents don't represent 'type of concept deepness'. Therefore the science textbooks needs to be restructuring.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.271-277
• /
• 2014

To overcome the limitations of the solid oxide fuel cells (SOFCs) due to the high temperature operation, there has been increasing interest in proton conducting fuel cells (PCFCs) for reduction of the operating temperature to the intermediate temperature range. In present work, the perovskite $BaCe_{0.85-x}Zr_xY_{0.15}O_{3-\delta}$ (BCZY, x = 0.1, 0.3, 0.5, and 0.7) were synthesized via solid state reaction (SSR) and adopted as an electrolyte materials for PCFCs. Powder characteristics were examined using X-ray diffraction (XRD), thermogravimetric analysis (TGA) and Brunauer, Emmett and Teller (BET) surface area analysis. Single phase BCZY were obtained in all compositions, and chemical stability was improved with increasing Zr content. Anode-supported cell with $Ni-BaCe_{0.55}Z_{0.3}Y_{0.15}O_{3-\delta}$ (BCZY3) anode, BCZY3 electrolyte and BCZY3-$Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-\delta}$ (BSCF) composite cathode was fabricated and electrochemically characterized. Open-circuit voltage (OCV) was 1.05 V, and peak power density of 370 ($mW/cm^2$) was achieved at $650^{\circ}C$.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.4
• /
• pp.191-197
• /
• 2013

The one of the cathode material, $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$, was synthesized by the precursor, $Ni_{0.5}Co_{0.2}Mn_{0.3}(OH)_2$, from the co-precipitation method and the morphologies of the primary particle of precursors were flake and needle-shape by controlling the precipitation parameters. Identical powder properties, such as particle size, tap density, chemical composition, were obtained by same process of lithiation and heat-treatment. The relation between electrochemical performances of $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ and the primary particle morphology of precursors was analyzed by SEM, XRD and EELS. In the $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ cathode from the needle-shape precursor, the primary particle size was smaller than that from flake-shape precursor and high Li concentration at grain edge comparing grain center. The cycle and rate performances of the cathode from needle-shape precursor shows superior to those from flake-shape precursor, which might be attributed to low charge-transfer resistance by impedance measurement.

• Corrosion Science and Technology
• /
• v.8 no.4
• /
• pp.162-169
• /
• 2009

Pure titanium and its alloys are drastically used in implant materials due to their excellent mechanical properties, high corrosion resistance and good biocompatibility. However, the widely used Ti-6Al-4V is found to release toxic ions (Al and V) into the body, leading to undesirable long-term effects. Ti-6Al-4V has much higher elastic modulus than cortical bone. Therefore, titanium alloys with low elastic modulus have been developed as biomaterials to minimize stress shielding. For this reason, Ti-30Ta-xZr alloy systems have been studied in this study. The Ti-30Ta containing Zr(5, 10 and 15 wt%) were 10 times melted to improve chemical homogeneity by using a vacuum furnace and then homogenized for 24 hrs at $1000^{\circ}C$. The specimens were cut and polished for corrosion test and Ti coating and then coated with TiN, respectively, by using DC magnetron sputtering method. The analyses of coated surface were carried out by field emission scanning electron microscope(FE-SEM). The electrochemical characteristics were examined using potentiodynamic (- 1500 mV~+ 2000 mV) and AC impedance spectroscopy(100 kHz~10 mHz) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The equiaxed structure was changed to needle-like structure with increasing Zr content. The surface defects and structures were covered with TiN/Ti coated layer. From the polarization behavior in 0.9% NaCl solution, The corrosion current density of Ti-30Ta-xZr alloys decreased as Zr content increased, whereas, the corrosion potential of Ti-30Ta-xZr alloys increased as Zr content increased. The corrosion resistance of TiN/Ti-coated Ti-30Ta-xZr alloys were higher than that of the TiN-coated Ti-30Ta-xZr alloys. From the AC impedance in 0.9% NaCl solution, polarization resistance($R_p$) value of TiN/Ti coated Ti-30Ta-xZr alloys showed higher than that of TiN-coated Ti-30Ta-xZr alloys.

• Journal of Life Science
• /
• v.24 no.8
• /
• pp.887-894
• /
• 2014

The screening of the microorganisms degrading chlorinated organic compounds such as PCP (pentachlorophenol) and TCE (trichloroethylene) was conducted with soil and industrial wastewater contaminated with various chlorinated organic compounds. Isolates (GP5, GP19) capable of degrading PCP and isolates (GA6, GA15) capable of degrading TCE were identified as Acetobactor sp., Pseudomonas sp., Arthrobacer sp., Xanthomonas sp. and named Acetobacter sp. GP5, Pseudomonas sp. GP19, Arthrobacer sp. GA6 and Xanthomoas sp. GA15, respectively. The microbial augmentation, OC17 formulated with the mixture of bacteria including isolates (4 strains) degrading chlorinated organic compounds and isolates (Acinetobacter sp. KN11, Neisseria sp. GN13) degrading aromatic hydrocarbons. Characteristics of microbial augmentation OC-17 showed cell mass of $2.8{\times}10^9CFU/g$, bulk density of $0.299g/cm^3$ and water content of 26.8%. In the experiment with an artificial wastewater containing PCP (500 mg/l), degradation efficiency of the microbial augmentation OC17 was 87% during incubation of 65 hours. The degradation efficiency of TCE (300 uM) by microbial augmentation OC17 was 90% during incubation of 50 hours. In a continuous culture experiment, analysis of the biodegradation of organic compounds by microbial augmentation OC17 in industry wastewater containing chlorinated hydrocarbons showed that the removal rate of COD was 91% during incubation of 10 days. These results indicate that it is possible to apply the microbial augmentation OC17 to industrial wastewaters containing chlorinated organic compounds.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.10 no.2
• /
• pp.71-81
• /
• 2002

The study was carried out to develop nursery soil for rice seedling of phyllite. First of all, physico-chemical properties of used phyllite in the study through the analysis for agricultural utilization evaluation are as following. Bulk density(BD) of phyllite was $1.31g/cm^3$ each other and porosity had 65% of entire pore size. Also, the water holding capacity(WHC) was 43% at 1/3bar pressure, which phyllite has high WHC. According to, the results the experiments for nursery soil were conducted by mixing the materials such as phyllite, zeolite and hill soil. The mixing ratios were 30, 50, and 70% for zeolite and hill soil into phyllite. These mixed materials were packed in a box by adding 0, 1 and 2g of N-fertilizer. At seedling test, there were increases in the growth of shoot and root of rice for phyllite to zeolite and phyllite to hill soil, respectively. On the other hand, the length of leaf increased with increasing application rate of phyllite, while length and a number of root increased with increasing application rate of hill soil. The growth in the plots of phyllite to zeolite and phyllite to hill soil was better than in control plot. Finally, phyllite plot had efficient results when it compared with others and the study used with phyllite will have to more research and effort for agricultural useful material.

• Applied Biological Chemistry
• /
• v.19 no.3
• /
• pp.145-154
• /
• 1976

Studies have been carried out to design a suitable consumer size package from flexible packaging material to hold 100 grams of Chilli powder and 250 grams of whole chilli which are moisture and color sensitive. 1. Sorption characteristics of the chilli powder has revealed that moisture sorption is rapid above 55 per cent R.H., and the product is fairly hygroscopic. Further, an equilibrium moisture content of about 15 per cent at 70 per cent R.H., appears to be critical from the point of microbial spoilage of chilli powder. 2. Studies on the colour (Capsanthin) changes of chilli powder equilibriated to different moisture content, have revealed that colour changes during storage is greatly influenced by the moisture content and temperature decreases the capsanthin content of chilli during storage. 3. From the studies, it can be inferred that the sunlight exhibits pronounced effect in bleaching of colour and brings about maximum discolouration of the red pigment in chilli. 4. From the packaging and storage studies of chilli powder in different flexible films, it can be concluded that for long-term storage, the aluminium foil laminate is unique in offering maximum protection from various physico-chemical changes. For short-term storage and for fairly good moisture and colour protection, amber or black polyethylene, high-density polyethylene and Saran/Cello/Saran poly laminate pouches appear to be suitable alternatives.