• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.461.2-461.2
• /
• 2014

양자점은 밴드갭을 조절할 수 있거나 multiple exciton generation등 과 같은여러가지 장점을 갖고 있어 양자점 감응형 태양전지에 대한 많은 연구가 진행되어왔다. 하지만 아직까지 이론적인 에너지 전환 효율에 비하여 낮은 효율을 보여주고 있다. 이러한 낮은 효율은 양자점과 전해질 계면에서의 defect나 surface state로 인한 전자-정공의 재결합으로 설명할 수 있다. 본 연구에서는 CdSe 양자점 합성법 중의 하나인 Chemical Bath Deposition의 전구체 농도조절을 통하여 고품질의 CdSe양자점을 합성하였다. 특정 농도에서 CdSe 양자점 표면에 생성되는 SeO2층을 억제하여 CdSe양자점/전해질 계면에서의 전하 재결합 저항을 높였고 가장 높은 에너지 전환 효율을 보여주었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.459.2-459.2
• /
• 2014

CdTe계와 CGIS계 태양전지의 광투과층으로 CdS 박막이 많이 사용된다. Cds 박막의 필요한 물성으로는 높은 광투과도와 얇은 두께이다. 광투과층으로 사용되는 CdS 막의 광투과도가 높아야 많은 양의 빛이 손실 없이 투과하여 광흡수층인 CIGS에 도달할 수 있다. 특히, CdS막의 두께가 얇으면 밴드 갭 이상의 에너지를 가지는 파장의 빛도 투과시킬 수 있어 태양전지의 효율의 증가을 얻을 수가 있다. 그러나 CdS 막의 두께가 얇을 경우, pinhole이 생성되는 등 막의 균질성이 문제가 된다. 본 연구에서는 높은 변환 효율을 갖는 CIGS 박막 태양전지 제작에 적합한 chemical bath depostion(츙)법을 이용하여 CdS 박막을 제조하였다. 또한 반응시간, Cd 및 S source 비와 같은 증착 조건에 따른 박막의 특성을 조사하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.459-460
• /
• 2008

Zinc oxide micro rods were fabricated using as chemical bath deposition ok photolithography. Vertically aligned Zinc Oxide rod array as grown by chemical bath deposition method on Zinc Oxide template layer. The ZnO template layer was deposited on glass and the pattering was made by standard photolithography technique. The selective growth of ZnO micro rods were achieved with the masked ZnO template layer substrate. The fabricated ZnO micro rods were found to be single crystalline and have grown along hexagonal c-axis direction of (0002) which is same as the preferred growth orientation of ZnO template layer. The ZnO micro-rod array structure was implemented as a window layer in Cu(InGa)Se2 solar cell and its effect on photovoltaic efficiency was examined.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.739-742
• /
• 2000

Nanostructured ZnS thin films were grown on the slide glass substrate by the chemical bath deposition using an aqueous so1ution Of ZnSO$_4$and CH$_3$CSNH$_2$at 95$^{\circ}C$. The average grain sizes of the ZnS thin film estimating from the Debye-Scherrer formula are 4.8 nm. The optical transmittance edge of the ZnS thin films (4.0 eV) was shifted to the shelter wavelength compared with that of the bulk ZnS (3.67 eV) due to the quantum size effects. The ZnS thin films showed a strong photoluminescence intensity and a sharp emission band from 410 to 480 nm 3t room temperature. The PWHM of photoluminescence peak was about 40 nm. For the viloet(410 nm) and blue(480 nm) emission of the ZnS thin films, the temperature dependence can be described by an Arrhenius equation with an activation energy of 168 and 157 meV, respectively.

• 한국표면공학회지
• /
• 제47권5호
• /
• pp.269-274
• /
• 2014

Electroless plating process as a solution deposition method is a viable means of preparing conductive metal films on non-conducting substrates through chemical reactions. In the present study, the preparation and properties of electroless Ni-plating on flexible silicone rubber are described. The process has been performed using a conventional Ni(P) chemical bath. Additives and complexing agents such as ammonium chloride and glycine were added and the reaction pH was controlled by NaOH aqueous solution. Ni deposition rate and crystallinity have been found to vary with pH and temperature of the plating bath. It was shown that Ni-films having the high crystallinity, enhanced adhesion and optimum electric conductivity were formed uniformly on silicone rubber substrates under pH 7 at $70^{\circ}C$. The conductive Ni-plated silicone rubber showed a high electromagnetic interference shielding effect in the 400 MHz-1 GHz range.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1995년도 추계 학술발표 강연 및 논문개요집
• /
• pp.86-86
• /
• 1995

• 한국재료학회지
• /
• 제22권12호
• /
• pp.664-668
• /
• 2012

ZnO nanorods were successfully fabricated on Zn foil by chemical bath deposition (CBD) method. The ZnO precursor concentration and immersion time affected the surface morphologies, structure, and electrical properties of the ZnO nanorods. As the precursor concentration increased, the diameter of the ZnO nanorods increased from ca. 50 nm to ca. 150 nm. The thicknesses of the ZnO nanorods were from ca. $1.98{\mu}m$ to ca. $2.08{\mu}m$. ZnO crystalline phases of (100), (002), and (101) planes of hexagonal wurtzite structure were confirmed by XRD measurement. The fabricated ZnO nanorods showed a photoluminescene property at 380 nm. Especially, the ZnO nanorods deposited for 6 h in solution with a concentration of 0.005M showed a stronger (101) peak than they did (100) or (002) peaks. In addition, these ZnO nanorods showed a good electrical property, with the lowest resistance among the four samples, because the nanorods were densely in contact and relatively without pores. Therefore, a ZnO nanorod substrate is useful as a highly sensitive biochip substrate to detect biomolecules using an electrochemical method.

• 한국재료학회지
• /
• 제22권10호
• /
• pp.504-507
• /
• 2012

Synthesis of RGO (reduced graphene oxide)-CdS composite material was performed through CBD (chemical bath deposition) method in which graphene oxide served as the support and Cadmium Sulfate Hydrate as the starting material. Graphene-based semiconductor photocatalysts have attracted extensive attention due to their usefulness for environmental and energy applications. The band gap (2.4 eV) of CdS corresponds well with the spectrum of sunlight because the crystalline phase, size, morphology, specic surface area and defects, etc., of CdS can affect its photocatalytic activity. The specific surface structure (morphology) of the photocatalyst can be effective for the suppression of recombination between photogenerated electrons and holes. Graphene (GN) has unique properties such as a high value of Young's modulus, large theoretical specific surface area, excellent thermal conductivity, high mobility of charge carriers, and good optical transmittance. These excellent properties make GN an ideal building block in nanocomposites. It can act as an excellent electron-acceptor/transport material. Therefore, the morphology, structural characterization and crystal structure were observed using various analytical tools, such as X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and Raman spectroscopy. From this analysis, it is shown that CdS particles were well dispersed uniformly in the RGO sheet. Furthermore, the photocatalytic property of the resulting RGO-CdS composite is also discussed in relation to environmental applications such as the photocatalytic degradation of pollutants. It was found that the prepared RGO-CdS nanocomposites exhibited enhanced photocatalytic activity as compared with that of CdS nanoparticles. Therefore, better efficiency of photodegradation was found for water purification applications using RGO-CdS composite.

• 센서학회지
• /
• 제2권1호
• /
• pp.81-86
• /
• 1993

Chemical bath deposition 방법으로 다결정 CdSe 박막을 세라믹 기판 위에 성장시킨 다음 온도를 변화시켜 열처리하고 X-선 회절무늬를 측정하여 결정구조를 밝혔다. $450^{\circ}C$로 열처리한 시료가 X-선 회절무늬로 부터 외삽법에 의해 $a_{o}$와 $c_{o}$는 각각 $4.302{\AA}$과 $7.014{\AA}$인 육방정계임을 알았다. 이 때 낱알크기는 약 $0.3{\mu}m$이었다. Van der Pauw 방법으로 Hall 효과를 측정하여 운반자 농도와 이동도의 온도의존성을 연구하였다. 이동도는 33 K에서 200 K까지는 압전산란에 의하여, 200K에서 293 K까지는 극성광학산란에 의하여 감소하는 경향을 나타냈다. 광전도 셀의 특성으로 스텍트럼 응답, 감도(${\gamma}$), 최대허용소비전력 및 응답 시간을 측정하였다.

• 공업화학
• /
• 제25권6호
• /
• pp.577-580
• /
• 2014

CIGS 태양 전지용 cadmium (Cd)-free $In(OH)_xS_y$ 버퍼층을 화학적 용액성장법을 이용해서 형성시켰고 최적 반응시간을 파악하였다. 투과율 측정과 함께 이온집적빔 시스템으로 직접 박막을 관찰해서 박막성장 조건을 최적화 하였으며 X선 회절분석법과 X선 광전자 분광법, 주사현미경을 이용해서 박막의 특성을 파악하였다. 그 결과 $In(OH)_xS_y$ 버퍼층의 증착을 위한 최적 반응 시간은 온도 섭씨 $70^{\circ}$의 조건에서 20 min임을 확인하였으며, 이때의 버퍼층의 두께는 57 nm 가량이었고 밴드갭 에너지는 2.7 eV를 나타내었다. 아울러 molybdenum (Mo)층과 CIGS층 위에서 $In(OH)_xS_y$ 버퍼층을 형성시키는 경우에 XPS 피크의 차이는 볼 수 없었다.