• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2013년도 전력전자학술대회 논문집
• /
• pp.329-330
• /
• 2013

In this research, a novel battery charge system with embedded diagnosis function is proposed by using online impedance spectroscopy. The impedance spectroscopy technique is employed to investigate the impedance variation of the battery thereby estimating the state of health of the battery. A small voltage perturbation is applied to the battery by the voltage controller of the bidirectional converter with no additional hardware and the impedance of the battery is then calculated by the digital lock-in amplifier embedded in the DSP of the charger. The design procedure of the proposed charger is detailed and the feasibility of the system is verified by the experiments.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2019년도 추계학술대회
• /
• pp.174-175
• /
• 2019

Battery cells are connected in parallel to enlarge the system capacity. However, cell inconsistency may reduce the overall system capacity and cause the over-charging or over-discharging issue. This paper proposes a SOC-based sequencing equalizer for parallel-connected battery configuration that uses the ANFIS (adaptive neuro-fuzzy inference system) algorithm to make the switching decision. Depend on the load current and the SOC (state-of-charge) rate of cells, the switching decision is made to equalize the SOC of the battery cells. The simulation results show that the system capacity is maximized and the controller is adaptive for a large number of parallel-connected in dynamic load profile.

• International Journal of Automotive Technology
• /
• 제6권5호
• /
• pp.529-536
• /
• 2005

This paper presents a novel design of a fuzzy control strategy (FCS) based on torque distribution for parallel hybrid electric vehicles (HEVs). An empirical load-regulating vehicle operation strategy is developed on the basis of analysis of the components efficiency map data and the overall energy conversion efficiency. The aim of the strategy is to optimize the fuel economy and balance the battery state-of-charge (SOC), while satisfying the vehicle performance and drivability requirements. In order to accomplish this strategy, a fuzzy inference engine with a rule-base extracted from the empirical strategy is designed, which works as the kernel of a fuzzy torque distribution controller to determine the optimal distribution of the driver torque request between the engine and the motor. Simulation results reveal that compared with the conventional strategy which uses precise threshold parameters the proposed FCS improves fuel economy as well as maintains better battery SOC within its operation range.

• 반도체디스플레이기술학회지
• /
• 제17권4호
• /
• pp.62-65
• /
• 2018

We will provides a micro-pump infusion injector with the cloud networking for remote control. The existing infusion injector with controlled manually have an uncomfortable to use it inconveniently. The proposed remote control infusion, infusion system enables the identification and control of injected amount through the IOT function on th WEB. The micro-pump used is a piezo electric pump manufactured by using MEMS technology, and the amount of charge is varied depending on the frequency magnitude through the micro-controller. The micro-pump can adjust the speed of the fluid depending on the frequency and can be from 0.1ml / min to 7ml / min when the frequency is from 3 to 110Hz.

• Design & Manufacturing
• /
• 제16권2호
• /
• pp.20-25
• /
• 2022

In line with the rapid economic growth of many countries, fossil fuel energy sources are also rapidly depleting. Therefore, the price is also rising rapidly, so it is necessary to develop new and renewable energy sources such as hydropower, geothermal power, nuclear power, wind power and solar energy to replace fossil fuel energy in the future. In this study, development of rotating concentrator module system, development of rotating module control control system, development of lamp and charge control controller, configuration and prototype production of rotating concentrating solar LED street light system, efficiency of rotating concentrating solar LED street light, and power production. The research was conducted in the order of evaluation of comprehensive performance tests such as consumption and consumption. As a result, the developed high-efficiency rotation-concentrating hybrid solar LED street light module system has a 50% higher light-gathering efficiency than existing products by tracing sunlight by self-developing a rotation-collecting module on existing solar LED street lamps according to the characteristics of Korea's topography. and the power generation was improved by more than 40%.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1020-1022
• /
• 2001

because the output of solar cell is direct, it is necessary to install D/A converter system for A.C load, and in case of driving utility line system, it is possible to drive system relation when the system supplies sinusodal current ant voltage having unit power factor. As the characteristics of the soar cell output the is influenced by dailysunight charge, for more electric power it is essential to control the direction toward the san so that the driving point of solar cell can always operate near maximum output point. PWM modulation device among electric power converters must have stable modulation at anytime when it includes noise-factors such as noise-wave and noises on electric voltage wave, a synchronous signal system. In dealing with synchronous signal for control and control signal by microprocessor, it is necessary to compensate it because there is time difference between sample paint and carrier wave. On this papers, single phase PWM current type invertor controled the solar cell having typical voltage dropping character has optimun short current in short, reduces D.C reactance, composes controller for modulation and keeps lower harmonic and high power factor keeping maximum output of solar cell according daily sunlight charge variation.

• 한국태양에너지학회 논문집
• /
• 제29권2호
• /
• pp.1-7
• /
• 2009

Use of the PV(photovoltaic) generation system is increased in such areas as remote mountain places or islands at which electrical energy is not serviced. The stand alone PV system is required the power storage products such as battery, fly wheel and super capacitor. Several lead storage batteries are connected in series to get high voltages. The life of lead storage battery is shortened when over charge or over discharge takes place. So, it is needed to control batteries not to be overcharged or be discharged deeply. Voltage of each battery was ignored in former control methods in which overall voltage was used to control charge or discharge battery. In this study, the charging and discharging voltage variations of sealed lead storage batteries with l2V/l.2A were investigated step by step experiments. The results of the test show that one should consider and specify the state of each battery to prevent overcharge or deep discharge. With the basis of the experiments, we designed a monitoring unit to monitor battery voltages simultaneously using micro-controller. The unit measures voltage of 20 batteries simultaneously and displays data on the color LCD monitor with curved line graph. It also sends data to PC using the RS232C communication port. The designed unit was adapted to stand alone PV system with 1kW capacity and lead storage batteries are connected to the PV generation system. The number of lead storage batteries was 10 in series and 12V/250Ah each. Resistive load with 3kW was used for discharging.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.1105-1118
• /
• 2015

Battery energy storage devices (ESDs) have become more and more commonplace to maintain the stability of islanded power systems. Considering the limitation in inverter capacity and the requirement of flexibility in the ESD, the droop control was implemented in paralleled ESDs for higher capacity and autonomous operation. Under the conventional droop control, state-of-charge (SoC) errors between paralleled ESDs is inevitable in the discharging operation. Thus, some ESDs cease operation earlier than expected. This paper proposes an adaptive accelerating parameter to improve the performance of the SoC error eliminating droop controller under the constraints of a microgrid. The SoC of a battery ESD is employed in the active power droop coefficient, which could eliminate the SoC error during the discharging process. In addition, to expedite the process of SoC error elimination, an adaptive accelerating parameter is dedicated to weaken the adverse effect of the constraints due to the requirement of the system running. Moreover, the stability and feasibility of the proposed control strategy are confirmed by small-signal analysis. The effectiveness of the control scheme is validated by simulation and experiment results.

• 전기전자학회논문지
• /
• 제23권3호
• /
• pp.1061-1067
• /
• 2019

본 논문에서는 PTWS 방식을 이용한 고집적화된 AMOLED용 3-채널 DC-DC 변환기의 설계한다. 양의 전압 $V_{POS}$는 경부하에서 효율을 제고하기 위해 SPWM 듀얼모드와 PTWS 방식을 적용한 부스트 변환기로 설계한다. 음의 전압 $V_{NEG}$는 전력 손실을 줄이기 위해 PSM 방식을 적용한 0.5x 인버팅 차지펌프를 이용해 설계하고, 추가적인 전압 $V_{AVDD}$는 LDO를 이용하여 설계한다. 제안된 DC-DC 변환기는 $0.18{\mu}m$ BCDMOS 공정을 사용하여 시뮬레이션을 한 결과 부하전류 1mA~70mA에서 전력효율 56.9%~90.2%를 가지고, 양의 전압 $V_{POS}$에서 최대 5mV의 출력 리플을 가졌다.

• 한국해양공학회지
• /
• 제17권5호
• /
• pp.82-87
• /
• 2003

A practical method to investigate the sharing architecture of FMS, for small and medium enterprises, on distributed heterogeneous environmental conditions is investigated. Because the industrial FMS model requires a reasonable size for actual work-site flexible operation, the initial facility expense is very heavy. The support for flexible cooperation of FMS, with some external different FMS, can reduce expenditures and provide greater functionality. While most FMS provide their operation process using an adequate mechanism, when used in isolation, such as island of automation, there is increasing demand for FMS that can cooperate. By exchanging intermediate products and information with other external FMS, products can be produced that cannot be produced alone, such as those that require various processes. This study first considers the sharing architecture of FMS for small and medium enterprises, and investigates the effects of the general sharing architecture of FMS on distributed heterogeneous environments, by using transducer approach to agentification. In this study, set-up station or in-out station takes charge of the gateway of intermediate products, and routes them among distributed heterogeneous FMS plants. The transducer approach is applied to web agent and set-up agent established interfaces, with system controller and setup controller. In this study, the FMS-established sharing architecture is able to obtain not only the internal flexibility, but also the external flexibility.