• 한국안전학회지
• /
• 제24권1호
• /
• pp.26-30
• /
• 2009

Shape memory recoverable stress and strain of Ti-42.5at%Ni-10at%Cu alloys were measured by means of constant temperature tensile tests. The alloys' transformation behavior is B2 - B19 by DSC result. The strain by tensile stress were perfectly recovered by heating at any testing conditions but shape memory recoverable stress increased to 66MPa and then slightly decreased. Transformation temperatures from thermal cycling under constant uniaxial applied tensile loads linearly increased by increasing tensile load and their thermal hysteresis are about 110K and their maximum recoverable strain is 6.5% at 100MPa condition.

• Transactions on Electrical and Electronic Materials
• /
• 제5권1호
• /
• pp.11-14
• /
• 2004

An rf triode magnetron sputtering system is designed and installed its construction in vacuum chamber. In order to calibrate the rf triode magnetron sputtering for thin films deposition processes, the effects of different glow discharge conditions were investigated in terms of the deposition rate measurements. The basic parameters for calibrating experiment in this sputtering system are rf power input, gas pressure, plasma current, and target-to-substrate distance. Because a knowledge of the deposition rate is necessary to control film thickness and to evaluate optimal conditions which are an important consideration in preparing better thin films, the deposition rates of copper as a testing material under the various sputtering conditions are investigated. Furthermore, a triode sputtering system designed in our team is simulated by the SIMION program. As a result, it is sure that the simulation of electron trajectories in the sputtering system is confined directly above the target surface by the force of E${\times}$B field. Finally, some teats with the above 4 different sputtering conditions demonstrate that the deposition rate of rf triode magnetron sputtering is relatively higher than that of the conventional sputtering system. This means that the higher deposition rate is probably caused by a high ion density in the triode and magnetron system. The erosion area of target surface bombarded by Ar ion is sputtered widely on the whole target except on both magnet sides. Therefore, the designed rf triode magnetron sputtering is a powerful deposition system.

• International Journal of Advanced Culture Technology
• /
• 제9권1호
• /
• pp.210-217
• /
• 2021

In the case of an agile-based project, it was inadequate to perform a comprehensive inspection and evaluation on the establishment and operation of an information system by performing audit only with the audit and inspection elements provided by the existing information system audit and inspection system. In particular, in the case of the test activity area, it was necessary to improve the test activity audit check items to comprehensively check the agile-based development process by applying the existing audit system. To this end, a test activity improvement check model of the agile methodology audit model was presented by applying the repetition concept, a characteristic of the agile methodology. In order to empirically verify the model of this study, a survey was conducted for auditors and designers/developers who have experience in performing agile-based projects and auditing information systems. As a result of the questionnaire on the integrated test and system test in the test stage, more than 70% of the respondents were found to be suitable. More than 80% of the respondents judged that it was appropriate as a result of the questionnaire on "improvement and regression test progress according to integrated test and system test results" and "integrated test and functional actions of components and subsystems".

• 설비공학논문집
• /
• 제2권1호
• /
• pp.37-48
• /
• 1990

The drag and heat transfer reduction phenomena and degradation effects of drag reducing polymer solutions which are known as the viscoelastic fluids are investigated experimentally for the turbulent circular tube flows. Two stainless steel tubes are used for the experimental flow loops. Aqueous solutions of Polyacrylamide Separan AP-273 with concentrations from 300 to 1000 wppm are used as working fluids. Flow loops are set up to measure the friction factors and heat transfer coefficients of test tubes in the once-through system and the recirculating flow system. Test tubes are heated by power supply directly to apply constant heat flux boundary conditions on the wall. Capillary tube viscometer and falling ball viscometer are used to measure the viscous characteristics of fluids and the characteristic relaxation time of a fluid is determined by the Powell-Eyring model. The order of magnidude of the thermal entrance length of a drag reducing polymer solution is close to the order of magnitude of the laminar entrance length of Newtonian fluids. Dimensionless heat transfer coefficients of the viscoelastic non-Newtonian fluids may be represented as a function of flow behavior index n and newly defined viscoelastic Graetz number. As degradation continues viscosity and the characteristic relaxation time of the testing fluids decrease and heat transfer coefficients increase. The characteristic relaxation time is used to define the Weissenberg number and variations of friction factors and heat transfer coefficients due to degradation are presented in terms of the Weissenberg number.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.88.1-88.1
• /
• 2010

In recent days, the study for the renewable energy is required to supplement traditional energy source. One of the renewable energy of Fuel Cell is classified according to the electrolytes. It is the MCFC (Molten Carbonate Fuel Cell) for this study. One of the equipments of the heat exchangers is important component for efficiency and cost. In MCFC system, several heat exchangers are used according to the application. It is named for the humidifier because it is to preheat the fuel and water so that a reactor will convert some of the incoming fuel to hydrogen. Then, hot side fluid service is used the exhausted gas from the fuel cell and cold side fluid service is the fuel and water. The operation temperature range is about 25~500 Celsius Degree. This heat exchanger has the problems of heat transfer considering to multiphase fluid and phase changing. So it is necessary to analyze the heat transfer characteristics and to propose the reasonable design methodology for the humidifier. In this study, the thermal characteristic for the humidifier is estimated by using commercial tool of heat exchanger design and rating. And this study provides the testing methodology and presents the results for test facility of fabrication and for testing.

• 비파괴검사학회지
• /
• 제25권2호
• /
• pp.127-132
• /
• 2005

광학기기용 렌즈는 결함이 없는 높은 형상정밀도가 요구되어지는 제품으로써 본 논문에서는 공명초음파 분광법을 이용하여 결함을 검출하는 시험을 하였다. RUS는 시험편을 가진 시켜 양품시험편과 결함을 갖는 시험편 사이의 공진주파수 차를 검사하는 측정시스템이다 RUS를 이용한 비파괴 평가를 위하여 우리는 구면렌즈와 비구면 렌즈의 공진주파수를 측정하였다. 그 결과, 우리는 측정된 공진주파수에 의해 구면렌즈의 연마 가공정도를 알 수 있었으며, 결함을 갖는 비구면 렌즈의 특성평가를 할 수 있었다.

• 한국정보처리학회논문지
• /
• 제4권2호
• /
• pp.395-400
• /
• 1997

소프트웨어 신뢰도는 소프트웨어의 중요한 품질 특성 중의 하나이며, 소프트웨어 신뢰도 성장 모형은 테스트 단계동안 신뢰도를 평가하고 신뢰도가 성장하는 양상을 파악 할 수 있는 도구이다. 그러므로 테스트 단계동안 수집된 고장 자료는 적절한 소프트웨어 신뢰도 모형에 의거해 계속적으로 분석된다. 비등질 포아송 과정 모형이 적절한 소프트웨어 신뢰도 성장 모형인 경우 고장 수 자료를 분석하기 위해서 포아송 희귀 모형을 세우고 모수들은 가장 최소 자승법으로 추정하는 것이 가능하며, 이렇게 구한 가장 최소 자승 추정량은 최우 추정량과 동일한 성질을 가짐을 보일 수 있다. 이 분석 방법을 대형 시스템으로부터 수집된 실제 자료를 분석하는데 적용한다.

• 비파괴검사학회지
• /
• 제31권5호
• /
• pp.516-521
• /
• 2011

청각기관인 달팽이관에 존재하는 기저막의 중요한 기능은 등자뼈로부터 전달되는 진동에너지를 주파수별로 분리하는 것이다. 본 연구에서는 인간 기저막의 형상을 모사하여 설계한 매크로 스케일의 폴리머 박막을 사용하여 주파수 분리 특성을 연구하였다. 각각의 폴리머 박막상의 위치에 따른 변위 분포는 LDV (laser Doppler vibrometer) 스캐닝 기법을 이용하여 측정하였고, 측정된 결과는 후처리 과정을 거쳐 주파수별로 분리하였다. 인가된 주파수에 따른 최대 변위 발생 위치를 추출하여 각 박막에 대한 주파수-최대 변위 발생 위치 관계를 도식화하였다. 아울러 박막 두께 및 물성치가 주파수-최대 변위 발생 위치 관계에 미치는 영향에 대해서도 논하였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.72-72
• /
• 2018

A dynamic fatigue characteristic of dental implant system has been evaluated with applying single axial compressive shear loading based on the ISO 14801 standard. For the advanced dynamic fatigue test, multi-directional force and motion needed to be accompanied for more information of mechanical properties as based on mastication in oral environment. In this study, we have prepared loading and motion protocol for the multi-directional fatigue test of dental implant system with single (Apical/Occlusal; AO), and additional mastication motion (Lingual/Facial; LF, Mesial/Distal; MD). As following the prepared protocol (with modification of ISO 14801), fatigue test was conducted to verify the worst case results for the development of highly stabilized dental implant system. Mechanical testing was performed using an universal testing machine (MTS Bionix 858, MN, USA) for static compression and single directional loading fatigue, while the multi-directional loading was performed with joint simulator (ADL-Force 5, MA, USA) under load control. Basically, all mechanical test was performed according to the ISO 14801:2016 standard. Static compression test was performed to identify the maximum fracture force with loading speed of 1.0 mm/min. A dynamic fatigue test was performed with 40 % value of maximum fracture force and 5 Hz loading frequency. A single directional fatigue test was performed with only apical/occlusal (AO) force application, while multi directional fatigue tests were applied $2^{\circ}$ of facial/lingual (FL) or mesial/distal (MD) movement. Fatigue failure cycles were entirely different between applying single-directional loading and multi-directional loading. As a comparison of these loading factor, the failure cycle was around 5 times lower than single-directional loading while applied multi-directional loading. Also, the displacement change with accumulated multi-directional fatigue cycles was higher than that of single directional cycles.

• 한국정밀공학회지
• /
• 제26권1호
• /
• pp.112-119
• /
• 2009

An automatic transmission of construction equipment is controlled by hydraulic and electronic system for doing in various functions like as shifting and operation. The shifting is operated by the engaged and disengaged clutch motion from hydraulic power. On the shifting process, suitable pressure control to the clutch is required for smooth shifting. Hydraulic control system in the automatic transmission is divided by the pilot control type and the direct control type greatly. The direct control type has an advantage than the pilot control type. Because the structure is simple, the design and the manufacture are having less troubles and the system can be maximized precision pressure control. However, the excellent performance proportional control valve should be used to achieve proper control-ability. In this study, the dynamic analysis model composing the automatic transmission and hydraulic system for forklift truck is presented to simulate the characteristics of hydraulic system about the direct control type. That model is verified the validity compared the results of the testing examination. Parameters of input signal are analyzed to reduce the output torque according to input control signal is affected in shifting characteristic.