• The Journal of Engineering Geology
• /
• v.4 no.2
• /
• pp.207-218
• /
• 1994

The natural constants of moving coil type geophone can be determined by free impedance and step force method. The former method was desirable for the measurement of natural frequency($f_o$), inertial mass(m) and damping factor($h_o$), but the latter method for sensitivity(G). In particular, the value by the latter method should be corrected for the noise by the long period movement of measurement device. The results of frequency characteristics from these constants operate the accelerometer and displacement system in the boundary of natural frequency.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.8
• /
• pp.61-67
• /
• 2010

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite-Difference Time-Domain (FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency-dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.67-75
• /
• 1998

This paper examined the geometrical variables of microstrip to control the characteristic impedance of MCM interconnect and also with respect to the practical requirements, evaluated the critical lengths for attenuation, propagation delay, and crosstalk at 500 MHz frequency compared to at 50 MHz frequency. With the illustration of each MCM-L and MCM-D interconnect having 50 characteristic impedance, it was revealed that the most important geometrical variables to control the characteristic impedance of microstrip are eventually dielectric thickness and line width. In particular, the dielectric thickness of MCM-D interconnect must be controlled with tolerance below 2 m. It is clear that the attenuation does not give rise to signal distortion in the range of up to 500MHz frequency for both MCM-L and MCM-D interconnects. However, the propagation delay is so significant that both MCM-L and MCM-D interconnects should be matched with load at the 500 MHz frequency. For the MCM-D interconnect, the crosstalk voltage would not be high to generate the wrong signal on the neighboring line at 500 MHz frequency, but the MCM-L interconnect could not be used due to severe crosstalk. Eventually, it is clear that the transmission line behavior must be studied for the design of MCM substrate at the 500 MHz frequency.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.4
• /
• pp.474-480
• /
• 2017

In this study, the evolution of electrical impedance of electric nodes was investigated to determine the setting time of cement paste using the electrical impedance spectroscopy method. The electric nodes were embedded in fresh cement paste and the electrical impedance signatures were continuously monitored. Vicat needle test and semi-adiabatic calorimetry test were also conducted to validate the electrical impedance spectroscopy method. During hydration period of cement paste, the magnitude of conductance gradually increased, and then started to decrease rapidly at a first certain time. After that, the magnitude of conductance gradually decreased at a second certain time. The times of turning point in the curves of magnitude of conductance seem to be related with the setting time by Vicat needle test. Also, the setting times by the electrical impedance spectroscopy method are well posed within the setting period estimated by the semi-adiabatic calorimetry test. Based on the results, it can be concluded that the setting time of cement paste can be effectively monitored through the electrical impedance spectroscopy method.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.11
• /
• pp.67-78
• /
• 2005

In this paper, impedance characteristics of overhead medium-voltage (MV) power line for power line communication (PLC) is analyzed. For analysis, a two-port equivalent network model of MV power lines is derived. By applying the equivalent model and basic transmission line theory, input impedance at the signal induction part is calculated. And also calculated input impedance of power line itself that the medium voltage coupler and coaxial cable effect are removed. For verification, impedance of power lines is measured at a test field for an MV PLC. The results show that impedance of MV power line itself is between $200\;{\Omega}\;and\;300\;{\Omega}$ and converges to a half of their characteristic impedance with increasing frequency. And also measured data is very similar to calculated data.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.37 no.1
• /
• pp.37-43
• /
• 2017

Ultrasonic transducers with high resolution and resonant frequency are required to detect small defects (less than hundreds of ${\mu}m$) by ultrasonic testing. The resonance frequency and resolution of an ultrasonic transducer are closely related to the thickness of piezo-electric materials, backing materials, and the electric impedance matching technique. Among these factors, electrical impedance matching plays an important role because it can reduce the loss and reflection of ultrasonic energy differences in electrical impedance between an ultrasonic transducer and an ultrasonic defects detecting system. An LC matching circuit is the most frequently used electric matching method. It is necessary for the electrical impedance of an ultrasonic transducer to correspond to approximately $50{\Omega}$ to compensate the difference in electrical impedance between both connections. In this study, a 15 MHz immersion ultrasonic transducer was fabricated and an LC electrical impedance circuit was applied to that for having broad-band frequency characteristic.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.3-7
• /
• 2004

An electric power efficiency of electrodeless fluorescent lamp has big relativie property of gas in lamp, gas pressure, lamp formation, ingredients of magnetic substance and shape and action frequency etc. We used magnetic substance that open self-examination material of electrodeless fluorescent lamp antenna. Ferrite that is used in this experiment was Mn-Zn type. We have examined resistance kind, impedance, Q-factor's frequency characteristic by ferrite. Impedance, resistance and capacitance did not show difference in start frequency 2.65 [MHz] but there was difference quantity. We could know Q-factor's difference according to material, and Q-factor's is important part of antenna design.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.480-481
• /
• 2015

General microstrip patch antenna has small bandwidth. If corner of a patch antenna is properly cutted to be triangular shape, then input impedance of patch antenna should be varied. Using this characteristic wideband patch antenna can be implemented. In this paper, wideband microstrip patch antenna operating in 2.4GHz ISM band is investigated through tracking variation of input impedance corresponding to cutting shape of patch antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.2
• /
• pp.167-177
• /
• 1996

The cutoff frequencies of a double ridged rectangular waveguide are calculated by applying the modal analysis to its cross-section. And the characteristic impedance of its $TE_{10}$ mode is evaluated in a frequency range of 6 to 18 GHz. When both ends of a linearly tapered rectangular wa- veguide consists of single and double ridged rectangular cross-sections, the equivalent nonuniform transmission line of its $TE_{10}$ mode is solved numerically. It is shown that the input impedance at its single ridged terminal becomes nearly constant in the wide bandwidth.

• Journal of Power System Engineering
• /
• v.13 no.1
• /
• pp.65-71
• /
• 2009

To address the need for new intelligent sensing, this paper introduces nano sensors made of carbon nanotube (CNT) composites and presents their preliminary experiments. Having smart material properties such as piezoresistivity, chemical and bio selectivity, the nano composite can be used as smart electrodes of the nano sensors. The nano composite sensor can detect structural deterioration, chemical contamination and bio signal by means of its impedance measurement (resistance and capacitance). For a structural application, the change of impedance shows specific patterns depending on the structural deterioration and this characteristic is available for an in-situ multi-functional sensor, which can simultaneously detect multi symptoms of the structure. This study is anticipated to develop a new nano sensor detecting multiple symptoms in structural, chemical and bio applications with simple electric circuits.