• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.725-726
• /
• 2008

This paper deals with characteristic analysis of Linear Switched Reluctance Motor (LSRM) according to switching condition. When approved current in each phase by decided position, we made sure current and voltage according to turn-on, turn-off. In dynamic simulation of LSRM, through an experiment, we decided turn-on position of inductance profile. Also, we presented dynamic characteristic analysis model which is consisted at motor and sensor signal part, etc., and substitute circuit constant that get using magnetic equivalent circuit method, we confirmed current and voltage waveform.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.25-30
• /
• 2003

Several desiccant cooling systems have been developed in terms of cost and performance. In this study a fin-tube exchanger has been used for liquid desiccant dehumidification system. This dehumidifier has been designed to study the absorption characteristic of the aqueous triethylene glycol(TEG) solution which has the flow range from 20 to 50 LPM. The dehumidifier performance characteristic of working factor variables such as inlet solution flow rate, air flow rate, solution concentration, solution temperature, brine temperature, air temperature and inlet air relative humidity has been analyzed. The result of this experiment can provide useful data for hybrid air conditioning system.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.200-203
• /
• 2002

This paper presents Continuous-current mode of $S^4$-PFC(Single-Stage Single-switch Power Factor Correction) converter. Proposed converter operates in the continueous current mode(CCM) at full load and discontinuous current mode(DCM) at light load. So, characteristic of proposed converter is no bus voltage stress and Zero Voltage Switching(ZVS) using resonant auxiliary circuit. And. This paper presents characteristic of $S^4$-PFC converter and effect of circuit parameter of proposed converter through the input inductor, PFC capacitor's variation. All of these theory and characteristic verified through the experiment with a 72W(12V, 6A), $90^{kHz}$ prototype converter.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.6
• /
• pp.26-34
• /
• 2011

Waterhammer and slamming phenomena can occur when power is cut off due to reversal flow in pipeline and sudden close of check valve. Therefore analysis of reversal flow time, which means the time of reversal flow in pipeline due to pumping station blackout, is needed to protect facilities from waterhammer economically and efficiently. However systematic study on reversal flow time has not been done yet. So theory of reversal flow time analysis is proposed and verified with experiment using several parameters like pump specific speed, motor pole number, and characteristic curve of pipeline in this study.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2345-2348
• /
• 1999

Existing $\psi$-AEA-t (phase-AEA-time) characteristic in polymer materials for power cable is good in general deterioration characteristic according to time variation, but it is difficult to clearly distinguish from deterioration state and diagnosis of deterioration is not enough to some extent. This paper is interpreted AE discharge statistics quantities measuring phase-amplitude variation of acoustic emission characteristic obtained from treeing breakdown experiment. Besides it can know useful discharge statistics quantities (AE average inception phase/amplitude, AE average maximum phase/amplitude) about so many for diagnosis of treeing deterioration.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2033-2035
• /
• 1998

This paper describes a DC-DC converter connected two unites inverters, a half-bridge type of high frequency resonance inverter, at the input with parallel. The proposed paper certified that theorem waveforms are equal to experiment waveforms, in addition, it estimated characteristics such as characteristic of average power, characteristic of average output voltage, characterisic of output voltage ripple etc., for designing the device with normalized parameter value.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.18-24
• /
• 2010

Because of the increasing demand on the high precision and high response of a machinery, electronic control valves are widely adopted at various application fields. This paper studies on the static characteristic of a first-stage proportional pressure control valve. At first an experimental apparatus including hyd. pump variable speed inverter, pressure and data aquisition system was setted up with the experimental apparatus, various tests such as P-Q-W test, hyd, pump, dynamic, static, frequency response test of the proportional valve was carride out and the results are discussed.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.870-872
• /
• 2000

This paper deals with the effect of rotor thickness variation and winding method in high torque hybrid Permanent Magnet(PM) step motor. As these parameters vary. The flux distribution in airgap and torque characteristics are influenced, which is related to output power. efficiency and cost. These parameters and characteristic variations were evaluated by using Finite Element Method (FEM) and experiment method. From these results. Characteristic analysis for the optimum design was studied and prototype motor was made to test performance analysis.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.876-878
• /
• 2000

In this paper, the characteristic of the Linear DC motor(LDM) are analyzed by using 3 Dimensional Equivalent Magnetic Circuit Network (3D EMCN), the movement of mover substitutes for the movement of magnetization in permanent magnet expressed by Fourier series, thrust characteristic analysis is performed and the appropriateness of analysed result is verified by comparing with the results of 2 Dimensional Finite Element Method (2D FEM) and experiment.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.6
• /
• pp.52-59
• /
• 2002

Resently, reduction of industrial products in size and weight has increased by the application of micro-drill for gadgets of high precision and gave rise to a great interest in a micro-drilling. Due to the lack of tool stiffness and the chip packing, micro-drilling requires not only the robust tool structure which has not affected by the vibration, but also the effective drilling methods designed to prevent tool fracture from cutting troubles. Firstly, this paper presents a optimum characteristic evaluation method of 0.15mm microdrill in consideration of new manufacturing processes for improving the product rate and extend the tool life, and secondly suggest between microdrilling characteristic properties of tool md evaluation of workpiece quality through experiment.