• 오토저널
• /
• 제2권1호
• /
• pp.39-50
• /
• 1980

This paper presents the variations obtained in heat flow rate and engine performance of a four-stroke cycle Diesel engine when there were changes in the temperature of cooling water, compression ratio, injection timing of fuel, and other factors. Heat dissipation of engine cylinder was calculated by the heat transfer coefficient of Nusselt's empirical equation and the analysis of distribution of temperature in cylinder barrel was obtained by the finite element method of two-dimensional steady state heat conduction. In this experiment, the out side temperature of cylinder liner was measured by the data logger, and the temperature distribution of liner was computed by the analysis of triangular finite element model under the assumption due to surface heat flux of cylinder inner surface. The results obtained by this study are as follows. Under the given operating condition, the temperature distribution of cylinder liner by using finite element method shows that the mean temperature of barrel is in accordance with the experimental results of Eichelberg and temperature difference is lower than 4.23.deg. C. The heat dissipation of engine decrease in accordance with the decrease of piston mean velocity, compression ratio, and the increase of coolant temperature. Influence on the delay of injection timing of fuel brings about the decrease of heat rejection over the cylinder at constant test conditions.

• Computers and Concrete
• /
• 제25권6호
• /
• pp.509-516
• /
• 2020

Adding fibers improves concrete performance in respect of strength and plasticity. There are numerous fibers for use in concrete that have different mechanical properties, and their combination in concrete changes its behavior. So, to investigate the behavior of the fiber reinforced concrete, an in vitro study was conducted on concrete with different fiber compositions including different ratios of steel, polypropylene and glass fibers with the volume of 1%. Two forms of fibers including single-stranded and aggregated fibers have been used for testing, and the specimens were tested for compressive strength and dividable tensile strength (splitting tensile) to determine the optimal ratio of the composition of fibers in the concrete reinforced by hybrid fibers. The results show that the concrete with a composition of steel fibers has a better performance than other compounds. In addition, by adding glass and propylene fibers to the composition of steel fibers, the strength of the samples is reduced. Also, if using the combination of fibers is required, the use of a combination of glass fibers with steel fibers will provide a better compressive strength and tensile strength than the combination of steel fibers with propylene.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2002년도 Proceedings
• /
• pp.356-358
• /
• 2002

MRI, particularly diffusion weighted imaging (DWI), plays vital roles in detection of the acute brain infarction$\^$1-4/ and others metabolic changes of biological tissues. In general, every molecule in biological tissues may diffuse and move randomly in three-dimensional space. However, in clinical diagnosis, only 2D-DWI is used. The authors have developed a new method for rapid three-dimensional DWI (3D-DWI). In this method, by refocusing of the magnetized spin with the applied gradient field, direction of which is opposite to phase encoding field. Magnetized spin of $^1$H is kept under the SSFP (steady state free precession)$\^$5-6/. Under SSFP, in addition of FID, spin echo and stimulated echo are also generated, so the acquired signal is increased. The signal intensity is increased depending on flip angle (FA) of magnetized spin. This phenomenon is confirmed by human brain and phantom studies. The performance of this method is quantitatively analyzed by using both of conventional spin echo DWI and 3D-DWI. From experimental results, three dimensional diffusion weighted images are obtained correctly for liquid phantoms (water, acetone and oil), diffusion coefficient is enhanced in each image. Therefore, this method will provide useful information for clinical diagnosis.

• 한국염색가공학회지
• /
• 제11권1호
• /
• pp.34-41
• /
• 1999

To examine the increase of paper strength by solvent-bonding using N-methylmorpholine N-oxide (NMMO), a paper was treated with aqueous solutions of NMMO, concentrated at $90^\circ{C}$ for selected periods of time, and pressed for 5 seconds followed by washing and drying. The effect of the increasing NMMO concentration on bonding state and some important properties of samples were mainly investigated. With increasing concentration of NMMO, the degree of bonding between fibers was increased, the fiber cross-sectional shape was changed from 'thin ribbonlike' to 'round rodlike' by swelling with solvent, and the longitudinal waves (crimp) were introduced to fibers, hence the shrinkage, weight per unit area, and thickness of paper were increased. Consequently, the tensile strength and elongation, under standard and wet conditions, and the stiffness were increased, and the water absorption was decreased generally with increasing concentration of NMMO. The moisture regain of treated samples was lower than that of the untreated sample, because of the reduction of space between fibers. But the moisture regain was increased a little with increasing concentration of NMMO due to the fiber swelling with NMMO followed by structural relaxation.

• Journal of Ginseng Research
• /
• 제25권2호
• /
• pp.82-88
• /
• 2001

This study was carried out to investigate a point of difference between normal and inferior Korean red ginseng (Naeback red ginseng = red ginseng with white part of clear boundary in phloem and/or xylem of ginseng body, saengnaeback red ginseng red ginseng with white part of indistinct boundary). White part with clear or indistinct boundary in center of ginseng body was observed in inferior red ginseng (naeback and saengnaeback red ginseng), and the differences in the internal color intensity was also found with naked eye. In hunter color values of normal and inferior parts of red ginseng in accordance with particle size, L value was increased with a diminishment in particle size, while a and b value were decreased. Absorbance at visible spectrum did not differ from water and 70% ethanol extract from normal and inferior parts of red ginseng, but absorbance in UV spectrum of extract from naeback part showed higher than those of normal and saengnaeback part. In comparison of intrastructure by electron microscope, the horizontal and vertical section of cortex and pith layer from normal part showed the very dense state, but small holes were found in naeback part of red ginseng by naked eye and electron microscope. The specific surface area of normal, naeback and saengnaeback part appeared 3.02, 3.33 and 6.55 ㎡/g, respectively. From above results, we consider saengnaeback red ginseng is red ginseng in the intermediate process which normal red ginseng changes to naeback red ginseng.

• Journal of Pharmaceutical Investigation
• /
• 제31권1호
• /
• pp.43-47
• /
• 2001

Sterically stabilized liposomes (SSL) have been introduced for longer circulation in blood than conventional liposomes (CL). However, there are a couple of problems in SSL preparation due to the instability of phospholipid and the degradation of drug in aqueous conditions. To solve these problems, it is necessary to go through lyophilization process. Therefore, in this study, effects of lyophilization on SSL were evaluated for physical characteristics changes upon rehydration of lyophilized SSL such as the particle size, efficiency of drug entrapment, turbidity and drug release. SSL containing streptozocin, a water-soluble anticancer drug as a model compound, were prepared with DSPC and DSPE-PEG 2000. The size was controlled to 100 nm by extrusion with polycarbonate membrane, and sucrose was used as a cryoprotectant for lyophilization at the 1:3 (lipid:sucrose) ratio. Upon rehydration of lyophilized SSL, the average size was in the range of $50{\sim}200\;nm$ which is adequate for longer circulation in blood, and the encapsulation efficiency was kept as its initial state. Rehydrated SSL were not adsorbed to rat plasma protein and revealed a similar drug release profile to that of fresh SSL before lyophilization. Therefore, lyophilization could be introduced efficiently to overcome aqueous instability problems of SSL.

• International Journal of Vascular Biomedical Engineering
• /
• 제2권2호
• /
• pp.16-26
• /
• 2004

The object of this study is to develop a mathematical model of the hemodialysis system including the mechanism of solute kinetics, water exchange and also cardiovascular dynamics. The cardiovascular system model used in this study simulates the short-term transient and steady-state hemodynamic responses such as hypotension and disequilibrium syndrome (which are main complications to hemodialysis patients) during hemodialysis. It consists of a 12 lumped-parameter representation of the cardiovascular circulation connected to set-point models of the arterial baroreflexes, a kinetic model (hemodialysis system model) with 3 compartmental body fluids and 2 compartmental solutes. We formulate mathematically this model in terms of an electric analog model. All resistors and most capacitors are assumed to be linear. The control mechanisms are mediated by the information detected from arterial pressoreceptors, and they work on systemic arterial resistance, heart rate, and systemic venous unstressed volume. The hemodialysis model includes the dynamics of urea, creatinine, sodium and potassium in the intracellular and extracellular pools as well as fluid balance equations for the intracellular, interstitial, and plasma volumes. Model parameters are largely based on literature values. We have presented the results on the simulations performed by changing some model parameters with respect to their basal values. In each case, the percentage changes of each compartmental pressure, heart rate (HR), total systemic resistance (TSR), ventricular compliance, zero pressure filling volume and solute concentration profiles are represented during hemodialysis.

• 한국환경농학회지
• /
• 제26권4호
• /
• pp.294-299
• /
• 2007

Natural gypsum has been used as a soil amendment in the United States. However, flue gas desulfurization (FGD)-gypsum has not traditionally been used for agricultural purpose although it has potential benefit as a soil amendment. To expand use of FGD-gypsum for agricultural purpose, the effect of FGD-gypsum on soil chemical properties was investigated in the field scales. Application rates for this study were 0 (control), 1.1, and 2.2 Mg ha-1 of FGD-gypsum. After two year application, the soil samples were taken to 110 cm depth and sub-sampled at 10 cm intervals. The heavy metal contents in FGD-gypsum were lower than ceiling levels allowed by regulations for land-applied biosolids. Soil pH was not largely affected by FGD-gypsum application. Although degree of calcium (Ca) saturation in surface horizons increases only slightly with respect to the control, there is a clear decrease in exchangeable aluminum (Al). FGD-gypsum clearly increases the soil electrical conductivity (EC) with increasing application rate. Water-soluble Ca and sulfate is increased with FGD-gypsum application and these ions moved to a depth of at least 80 cm after only 2 years. We conclude that surface application of FGD-gypsum can mitigate toxicity of Al and deficiency of Ca in subsoil of acid soil.

• Composites Research
• /
• 제30권3호
• /
• pp.188-192
• /
• 2017

The mechanical properties of composites are significantly affected by external environment. It is essential to understand the degradation of material performance and judge the material's lifetime in advance. In the current research, changes in mechanical properties of glass fiber and unsaturated polyester composite materials (GFRP, Glass fiber reinforced plastic) were investigated under different bending stress and submerged in hot water at a temperature of $80^{\circ}C$. Loading time of 100 H (hours), 200 H, 400 H, 600 H, 800 H for testing under stresses equal to 0% (stress-free state), 30%, 50% and 70% of the ultimate strength was applied on the GFRP specimens. From the values of bending stress, obtained from three-point bending test, fracture energy, failure time, and life curve were analysed. Moreover, a normalized strength degradation model for this condition was also developed. It was observed that within 100 H, the decline rate of the bending strength was proportional to the pressure.

• 한국식품저장유통학회지
• /
• 제31권1호
• /
• pp.46-63
• /
• 2024

This study evaluated the impact of storage temperature on the quality characteristics of texturized vegetable protein (TVP). TVP was prepared by mixing defatted Daewon soybean flour at 80℃, gluten, and corn starch in a 5:3:2 ratio, which was then extruded at a screw speed of 250 rpm and a barrel temperature of 190℃ with moisture addition at 9 rpm. Subsequently, the extruded TVP was vacuum-sealed in polyethylene packaging and stored at -20℃, 0℃, and 4℃ for 9 days. Texture analysis revealed that the curing rate followed 4℃ > 0℃ > -20℃ sequence. No significant color variation was observed across the storage conditions, although water content increased at all temperatures. Notable changes were detected in moisture absorption capacity (%) and solid leaching (%), following the order of -20℃ > 0℃ > 4℃. The turbidity of the solution released during cooking varied, with the highest to the lowest sequence being -20℃ > 4℃ > 0℃, while pH levels remained neutral. Regarding free amino acids, sweetness and textural quality improved with storage across all temperatures, whereas bitterness components diminished at 4℃. The study suggests that refrigerated storage at 4℃ is a viable method for distributing TVP, which was previously distributed only in a frozen and dry state.