• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.505-509
• /
• 2011

The combustion chamber and nozzle of a liquid rocket engine should be protected from the high temperature combustion gas generated by the chamber. An upper-stage nozzle extension has a large expansion ratio, therefore, The light-weight refractory materials have been used since the weight impact on the launcher performance is crucial. Gas film cooling and ablative cooling methods were used before, but were not applicable nowadays. Radiative cooling method with niobium alloy, Ni-based superalloy and ceramic based composite has been used to this day.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.300-310
• /
• 1999

A constant-volume combustion chamber is developed to measure the burnt gas temperature over the wide ranges of equivalence ratio from 1.5 to 2.7 and pressure from 0.1 to 2.7 and pressure from 0.1 to 6 MPa by two-color method. The combustion temperature is also calculated by the conventional two-region model. The premixed fuel rich propane-oxygen-inert gas mixtures under high pressures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree intervals. The eight converging flames compress the end gases to high pressures. The transmissiv-ity in the chamber center during the final stage of combustion at the highest pressure is measured by in situ laser extinction method. Comparisons are made with the combustion temperatures between two-color method and two-region model. It is found that the burnt gas temperature mea-sured by two-color method is higher than that calculated by two-region model because of being the negative temperature gradient on the calculation and the temperature distribution of light path-length on the measurement and the burnt gas temperature for the turbulent combustion is higher than that of the laminar combustion under the same conditions because the heat loss for turbulent combustion is lower due to the shorter combustion period.

• Korean Journal of Environmental Biology
• /
• v.36 no.4
• /
• pp.507-516
• /
• 2018

The closed chamber method, which is one of the most commonly used method for measuring greenhouse gases produced in rice paddy fields, has limitations in measuring dynamic $CH_4$ flux with spatio-temporal constrains. In order to deal with the limitation of the closed chamber method, some studies based on open-path of eddy covariance method have been actively conducted recently. The aim of this study was to compare the $CH_4$ fluxes measured by open-path and closed chamber method in the paddy rice fields. The open-path, one of the gas ($CO_2$, $CH_4$ etc.) analysis methods, is technology where a laser beam is emitted from the source passes through the open cell, reflecting multiple times from the two mirrors, and then detecting. The $CH_4$ emission patterns by these two methods during rice cultivation season were similar, but the total $CH_4$ emission measured by open-path method were 31% less than of the amount measured by closed chamber. The reason for the difference in $CH_4$ emission was due to overestimation by closed chamber and underestimation by open-path. The closed chamber method can overestimate $CH_4$ emissions due to environmental changes caused by high temperature and light interruption by acrylic partition in chamber. On the other hand, the open-path method for eddy covariance can underestimate its emission because it assumes density fluctuations and horizontal homogeneous terrain negligible However, comparing $CH_4$ fluxes at the same sampling time (AM 10:30-11:00, 30-min fluxes) showed good agreements ($r^2=0.9064$). The open-path measurement technique is expected to be a good way to compensate for the disadvantage of the closed chamber method because it can monitor dynamic $CH_4$ fluctuation even if data loss is taken into account.

• Journal of Life Science
• /
• v.11 no.2
• /
• pp.166-172
• /
• 2001

Various types of the seeding of bottle gourd widely used as a rootstock of watermelon has been required to satisfy the farmers need. The study was done to determine the effect of light quality of blue, red and far-red lights treated with light emitting diodes on growth and morphology of bottle goured seeding and chlorophyll content of its cotyledons. The lights were treated in the growth chamber for 7 days to the seeding elapsed 8 days after sowing under natural condition, and 64 hole trays with commercial bedsoil. Plant height, length and diameter of hypocotyl, leaf area of cotyledon and first true leaf, its leaf length, number of true leaves, fraction and total dry weight were measured. Red light shortened and slenderized the hypocotyl, which lengthened by far-red light and thickened by blue light. Plant height was declined in order of far-red light treatment, blue and red lights mainly due to difference of hypocotyl length, Area and length of the first true leaf became smaller and shorter under far-red light than under the other lights. However, blue light increased leaf area of cotyledons. Two cultivars cv. Yongjadaemok and cv. Kunghap had different response to the light treatments in total seedling dry weight(dw); far-red and red light treatments showed the greatest and the least dw of hypocotyl, respectively, while blue and red lights did the greatest dw of the other organs. Among the ratio of each organ dw to total dw, those of hypocotyl and true leaves were different between the light treatments; the highest ratio of hypocotyl dw to total dw was observed in far-red light treatment but the lowest was in red light treatment. Those of the true leaves were the lowest in far-red light and similar response in blue or red light treatment. Chlorophyll content of cotyledons was decreased in order of red light treatment, blue and far-red lights, meaning that short period light treatment may influence photosynthesis of seeding and afterward its growth.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.1 no.1
• /
• pp.10-17
• /
• 1978

The experiment were carried out to determine the rate of regrowth, the changes of carbohydrates contained in the samples right after cutting, plant part for storage of carbohydtates and top-dressing time of ladino clover and orchardgrass. Plants were grown in the simple growth chamber as well as in the fields. The temperature, light intensity and light period were controlled to be 15-20$^{\circ}$, 4,250 Lux, and 15 hours in the simple growth chamber. The results obtained are as follows ; 1. The period of recovery to initial stands after cutting was about 3 weeks in ladino clover and 4-5 weeks in orchard grass in terms of dry matter and carbohydrates. 2. The content of total water-soluble carbohydrates of plant parts was the hightest in stolon of ladino clover and in sheath of orchardgrass, and the lowest in roots of ladino clover and orchardgrass. 3. Cutting resulted in a temporary decrease of total water-soluble carbohydrates in the shoots. Similar trends were observed when the plants were left intact with top-dressing. 4. The top-dressing applied simultalliousely with the cutting was more effective to stimu1ate regrowth than that applied after cutting, however, both of the simultaneous and after cutting application were still better than application prior to cutting.

• Korean Journal of Environmental Biology
• /
• v.20 no.1
• /
• pp.20-24
• /
• 2002

We have from water samples of Kwalim, Dochang, and Mulwang reservoirs in Kyonggi-Do, where cyanobacteria blooming occurred. Isolated microbes which have lytic activity for cyanobacteria. Water samples were smeared on the Anabaena cylindrica lawn and incubated in light chamber at $28^\circ{C}$, under 3000 lux for 13 days. A fungus having cyanobacterial lytic activity was isolated from the samples of Dochang reservoir. The isolate was identified as Cryptococcus laurentii by Vitek system. From the culture of the isolate, four major extracellular protein bands (29, 35.2, 40.9, 51.1 kDa) have been detected and the 29 kDa protein band was more thickly appeared in the culture with cyanobacteria.

• Current Industrial and Technological Trends in Aerospace
• /
• v.9 no.1
• /
• pp.139-149
• /
• 2011

The combustion chamber and nozzle of a liquid rocket engine need thermal protection against the high temperature combustion gas. The nozzle extension of a high-altitude engine also has to be compatible with high temperature environment and several kinds of cooling methods including gas film cooling, ablative cooling and radiative cooling are used. Especially for an upper-stage nozzle extension having a large expansion ratio, the weight impact on the launcher performance is crucial and it necessitated the development of light-weight refractory material. The present survey on the nozzle extension materials employed in the liquid rocket engines of USA, Russia and European Union has revealed a trend that the heavier metals like stainless steels and titanium alloys are being substituted with light weight carbon fiber or ceramic matrix composite materials.

• The Korean Journal of Ecology
• /
• v.8 no.2
• /
• pp.69-73
• /
• 1985

Germination respone to sulfuric acid treatment, temperature, light and underwater condition were experimented for Albizzia julibrissin Durazz. seed. It took 60 minutes to break the dormancy of impermeable seed for the effective sulfuric acid treatment, and temperature sensitivity was decreased by 90 minutes' treatment. The germination rate of the seed was highest, i.e. 96% at 60 minutes acid treatment in a 21。C growth chamber. On the occasion of light sensitivity, the seed was light indifferent. The imbibition rate of seed was higher at 27。C than 21。C and in proportion to the period of acid treatment time. A. julibrissin Durazz. seed were well germinated at underwagter condition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.356-360
• /
• 2006

Recently, for the purpose of improving the isolation performance of impact noise, many resilient materials have been installed in a residential building. As one of the reduction method for improving the performance of light-weight impact noise, this study is focused on the load condition of floating layer over resilient material. We studied the correlation between the mass or load of the floating layer and the reduction of light-weight impact noise by experiments in reverberation chamber for testing the impact noise. The results show that the reduction of impact noise is improved by increasing the mass per unit area of floating layer until about $140kg/m^2$. But the reduction is not obvious by adding extra mass on the floating layer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.43-49
• /
• 2001

In order to satisfy the ULEV emissions regulation, fast light-off of a catalyst is essential for reduction of HC and CO emissions during the cold start. Cranking Exhaust Gas Ignition(CEGI) method developed in this study showed that the catalyst reaches the light-off temperature in a few seconds. The CEGI stops the ignition signal for a few seconds during the cranking period, so the unburned fuel-air mixture bypasses the combustion chamber and flows through the exhaust manifold. When the unburned mixture reaches two glow plugs installed upstream of the catalyst, it burns and releases the thermal energy to heat up the catalyst, In the FTP-75 vehicle tests, the CEGI showed that the exhaust emissions reduced by 47.7% for THC and by 88.6% for CO in the cold-transient phase of the test.