• International Journal of Precision Engineering and Manufacturing
• /
• 제3권3호
• /
• pp.56-61
• /
• 2002

CuFe$_2$O$_4$ ferrite was machined with cermet tools to clarify the machinability. The tool wear became the smallest at the cutting speed of 90m/min with the depth of cut of 0.2mm. The surface roughness became larger with increasing the cutting speed and the chamfer angle of tool. The tool with the chamfer angle of 15° showed the smallest wear. The surface roughness increased almost proportionally with the increase of chip size. The tool wear reduced with increasing feed in the depth of cut not more than 0.2mm.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.8-12
• /
• 2012

Recently, a wide range of industrial production area has a competitive advantage through cost reduction. Moreover with the development of industrial technology, base material and cutting tool help the machining technology. But most of the machining enterprises have not hold the R&D facilities and human resources. This mainly disturbs the industrial development and th increase of production efficiency. Especially in the interrupted machining process, it showed different behavior with continuous machining process. So it needs to research and develop the tool life and tool wear mechanism analysis.

• 한국주조공학회지
• /
• 제42권3호
• /
• pp.191-197
• /
• 2022

This study aims to improve the machinability of gray cast irons in high speed cutting by using nonmetallic inclusions. In this research, small quantities of AL and Mg were added to conventional gray cast irons without influencing their mechanical characteristics and castability to investigate the effects of these nonmetallic inclusions in the gray cast irons on tool wear in high speed cutting. During the high speed turning of gray cast iron containing Al and Mg using a cermet tool, protective layers consisting of Al, Mg, Si, Mn, S and O were detected on the flank face and rake face of the tool, and flank and crater wear were significantly reduced compared to the turning of conventional gray cast iron and gray cast iron added with Al. The effect of inclusions on tool wear increased with increasing cutting speed, and flank and crater wear was the smallest at the cutting speed of 700m/min. Moreover, in face milling, the addition of Al and Mg drastically decreased the wear rate, and wear hardly progressed even in prolonged cutting length after initial wear. The amount of adhesion on tool faces increased as the cutting speed increased. This increase in cutting speed resulted in the formation of a thick protective layer and the reduction of tool wear. Furthermore, the addition of small amounts of Al and Mg prevented thermal cracks in the face milling of gray cast irons.

• 열처리공학회지
• /
• 제6권1호
• /
• pp.1-8
• /
• 1993

In this paper, the surface roughness influenced by Sm45C hardness in high frequency induction hardening and mechanical characteristics for the changed Hv 598 part and the unchanged hardness Hv 223 part by use of cermet and ceramic cutting tools was experimentally examined. Finally, we could be had some important results by processing surface roughness on cutting conditions such as cutting speed, feed rate, depth of cut and changes of tool nose radius. The results are summarized as follows. 1. In case of the same cutting condition, the hardness of workpiece was high and acquired the best processing surface roughness when the radius of the tool nose had 0.8 mm and feed rate was 0.04 mm/rev. 2. In case of the hardness of workpiece, though the cutting speed didn't have an effect on processing surface roughness, the less feed rate and the more processing surface roughness improved. On the other hand, the low inside the hardness of workpiece, the more cutting speed and the more feed rate increase, the processing surface of roughness improved. 3. Regardless of the hardness of workpiece, the change of the cutting depth didn't have great effect on the surface roughness. 4. On cutting the high surface hardness part with cutting tools of cermet and ceramic, it can be acquired the higher processing surface roughness because it hadn't been taken effect on cutting speed, In case of the cutting process of the low inside hardness part the two cutting tools have acquired the similar processing surface roughness.

• 한국기계가공학회지
• /
• 제21권4호
• /
• pp.23-30
• /
• 2022

Small-scale production is increasing, and the manufacturing industry is gradually changing into a smart manufacturing industry. Therefore, research on securing optimal cutting conditions for factors affecting machining precision during cutting is very important. Therefore, the purpose of this study is to After machining the inner diameter hole of SCM415 steel with a cermet tool on a CNC automatic lathe, the surface roughness, dimensional accuracy, and dimensional straightness are measured according to the feed rate to analyze the machining characteristics and suggest optimal cutting conditions. The test material was cut using a cermet tool for secondary cutting after a round bar with a diameter of 20 mm was mounted on a CNC automatic lathe. The cutting length was fixed at 0.5 mm, and the cutting speed was fixed at 3200 rpm. When the feed rate was changed to 0.05, 0.1, and 0.15 mm/rev, the respective surface roughness during the 15th test was measured. Consequently, The lower the feed rate, the better is the surface roughness. In addition, the optimum cutting conditions for SCM415 steel were observed to be the most ideal cutting conditions than the condition of 0.05 mm/rev at a cutting speed of 3,200 rpm and a feed rate of 0.1 mm/rev.

• 대한기계학회논문집A
• /
• 제36권6호
• /
• pp.591-598
• /
• 2012

본 연구에서는 CNC선반을 사용하여 다양한 공구재질과 절삭속도에서 벌크금속유리(BMG)의 절삭 특성을 평가하였다. 선반가공시 Zr-기 BMG의 표면거칠기와 칩 형상을 관찰하여 가공조건에 따른 절삭력과 공구툴 마모 등 절삭 특성을 비교 검토하였다. 직경 8 mm $Zr_{50}Cu_{40}Al_{10}$ BMG시험편의 절삭에는 네 종류의 절삭공구를 사용하였다. 가공후 BMG 시험편의 표면거칠기를 측정하였고, 표면거칠기에 미치는 공구 회전속도의 영향을 조사하였다. 회전속도가 빠를수록 낮은 표면거칠기를 나타내었고, 공구 재질의 영향도 크게 나타났다. 칩 형상의 관찰 결과, 산화를 일으키지 않은 BMG 칩은 단열 전단띠 발생과 함께 나선형상의 형태를 나타내지만, 산화를 일으킨 칩은 국부적으로 용융과 함께 칩들이 뭉치는 현상을 나타내었다. BMG시험편을 가공하는 동안 발생한 절삭력은 TiN-WC에서 가장 큰 값을 나타내고, PCD가 그 다음, Cermet툴에서 가장 작은 값을 나타내었다.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.651-659
• /
• 2010

When high-speed interrupted cutting is carried out for die and mold steels with high hardness, CBN tools manifested a significantly longer wear life than carbide, ceramic, or cermet tools in an experiment of face milling characteristics. In addition, it was also found that they secured a stable surface roughness within a range of 1.6 S~6.3 S, an acceptable range for precision machining for polished machining parts. And it makes them acceptable in the precision machining field, except in industries where very high machining accuracy is required. In the high hardness interrupted cutting, it was advantageous to perform a negaland treatment and a honning treatment on the tools' cutting edge to extend tool life and surface roughness. Also, severe crater development was found on the sloped face in CBN tools following high-speed machining. This caused the cutting edge to be weakened and damaged, and ultimately resulted in a shorter tool life. Finally, as a result of EDX mapping inspection, Cr component was detected evenly on the entire crater wear area, which can be included only in STD 11.

• 한국공작기계학회논문집
• /
• 제14권5호
• /
• pp.80-86
• /
• 2005

High velocity oxy-fuel thermally sprayed coating of the WC-Co cermet material is a well-established process for modifying the surface properties of the structural components exposed to the corrosive and wear attacks. The hard WC phase in the coating resists to the wear while the soft metallic Co increases the adhesive and cohesive bonding properties. The coating properties deposited by the HVOF process are greatly dependent on the feedstock materials and processing parameters. The effects of the feedstock material and process coating parameters including the in-flight particle parameters and resultant coating microstructures were observed in this paper.

• Structural Engineering and Mechanics
• /
• 제61권4호
• /
• pp.519-526
• /
• 2017

In the present paper, the effects of cutting parameters and coating material on the performances of cutting tools in turning of AISI 52100 steel are discussed experimentally. A comparative study was carried out between uncoated and coated (with TiCN-TiN coating layer) cermet tools. The substrate composition and the geometry of the inserts compared were the same. A mathematical model was developed based on the Response Surface Methodology (RSM). ANOVA method was used to quantify the effect of cutting parameters on the machining surface quality and the cutting forces. The results show that feed rate has the most effect on surface quality. However, cutting depth has the significant effect on the cutting force components. The effect of coating layers on the surface quality was also studied. A lower surface roughness was observed when using PVD (TiCN-TiN) coated insert. A second order regression model was developed and a good accuracy was obtained with correlation coefficients in the range of 95% to 97%.