• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.349-352
• /
• 1989

Poling piezoelectric ceramic-polymer composites with 0-3connectivity is difficult because of the high dielectric constant of most of the ferroelectric filler materials, and the high resistivity of the polymer matrix. To aid in poling this type of composite, conductivity of the polymer phase can be controlled by adding small amount of a semiconductor phase such as germanium, carbon or silicon. In this study, flexible piezoelectric composites of $PbTiO_3$ powder and Eccogel polymer were developed using small amounts of a semiconducting phase. These composites were poled rapidly at low voltages, resulting in properties superior to composites prepared without a conductive phase. The effect of addition of various conductive phase with different volume percentage on the dielectric and piezoelectric properties of the composite are discussed here.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.367-374
• /
• 1994

Inorganic-organic composite was made through sol-gel process. Possible range for hosting organic dye was investigated with various composition. The transmittance of the composite was the most important condition for a host was increased to 90% with decreasing HCl as a catalyst. Clear absorbance peak was obtained by decreasing concentration of organic dye, fluorescent intensity was increased and transmittance was decreased with rising gelling temperature.

• Journal of the Korean Ceramic Society
• /
• v.43 no.8 s.291
• /
• pp.486-491
• /
• 2006

A new $TiN-Ti_5Si_3$ bulk composite was synthesized from preceramic, inorganic polymer (methylpolysilsesquioxane) and $TiH_2$ filler powders via polymer pyrolysis. Using this process, ceramics with high melting points can be produced relatively easily to a near net shape. The $TiN-Ti_5Si_3$ composite oxidized slowly during heating to $1000^{\circ}C$. During heating at the temperatures of at 700 and $800^{\circ}C$, TiN oxidized to Rutile-$TiO_2$ whereas $Ti_5Si_3$ resisted to oxidation. The oxide scale formed consisted primarily of $TiO_2$ containing $Ti_5Si_3$.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.7 no.1
• /
• pp.18-26
• /
• 1998

The improvement of esthetic dentistry has been accelerated from the development of composite resin and dentin-enamel adhesive since 1980's. The indirect composite resin restorations have more accurate proximal contact point and occlusal form than direct restoration. And the side effect of resin shrinkage is minimal because the amount of composite used in oral cavity is limited in cement space. As a results, marginal leakage, hypersensitivity, secondary caries, and discoloration are significantly diminished. The first generation laboratory composite resin used in indirect resin restoration had been widespread in 1980's and the second generation laboratory composite resins were developed in 1990's. The second generation laboratory composite resins are called Ceramic Polymer. The physical properties of Ceramic Polymer are improved because of high content of inorganic filler, and the esthetics and biocompatibility are better than that of the first generation resin. So the application range using composite resin have been broadened. The purpose of this paper is to introduce Targis & Vectris system that is classified to second generation laboratory composite and to report several cases in which the system was utilized for restoration.

• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.237-244
• /
• 1993

The characteristics of composite polymer electrolytes obtained by adding a fine ceramic powder($\gamma-{LiAlO}_{2}$) with a diameter of $1{\mu}$m to a poly(ethylene oxide)/lithium trifluoromethane sulfonate (LiC$F_3$S$O_3$) complex are described in terms of morphological and mechanical behavior. The addition of uniformly dispersed ceramic powder greatly improves the electrical and mechanical properties of solid polymer electrolytes at ambient temperature. For the composite polymer electrolytes under this study, the optimum composition of the $\gamma-{LiAIO}_{2}$ in the composite for maximum ionic conductivity was found to be 20 wt%.

• Journal of Powder Materials
• /
• v.25 no.6
• /
• pp.501-506
• /
• 2018

With the recent remarkable improvements in the average speeds of contemporary trains, a necessity has arisen for the development of new friction modifiers to improve adhesion characteristics at the wheel-rail interface. The friction modifier must be designed to reduce slippage or sliding of the trains' wheels on the rails under conditions of rapid acceleration or braking without excessive rolling contact wear. In this study, a novel composite material consisting of metal, ceramic, and polymer is proposed as a friction modifier to improve adhesion between wheels and rails. A blend of Al-6Cu-0.5Mg metallic powder, $Al_2O_3$ ceramic powder, and Bakelite-based polymer in various weight-fractions is hot-pressed at $150^{\circ}C$ to form a bulk composite material. Variation in the adhesion coefficient is evaluated using a high-speed wheel-rail friction tester, with and without application of the composite friction modifier, under both dry and wet conditions. The effect of varying the weighting fractions of metal and ceramic friction powders is detailed in the paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.349-349
• /
• 2005

수동소자를 PCB(Printed Circuit Board) 안으로 집적하기 위한 방법의 일환으로 polymer-metal, polymer-ceramic composite에 연구가 국내외 연구 국내외 연구기관에서 광범위하게 진행되고 있다. 본 연구에서는 polymer-metal-ceramic composite 에서 PZT-coated Ni의 volume fraction에 따른 유전율 변화에 대하여 조사하였다. 원료로는 PZT(52/48) solution. 니켈금속분말, PMMA(polymethyl methacrylate)를 사용하였다. 전기적 특성은 임피던스분석기를 이용하여 측정하였으며 mixing rule과 percolation theory를 이용하여 결과를 해석하였다.

• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.605-612
• /
• 1990

In Pb1-xLax(Zry, Tiz)1-x/4O3 system, it selects the composition 7/65/35 (x=7, y=65, z=35) that was reported to have eminent Pyroelectric properties, and that is sintered with PbZrO3＋0.3wt.% PbO2 atmosphere powder. From the sintered ceramic and Poly Vinyl Alcohol, the thin wafers are fabricated with 0-3connectivity, and they are researched in Pyroelectric properties and the others according to volume ratio between ceramic and polymer. It was possible to fabricate the film containing ceramic up to 80vol% in PVA polymer. The increment of PLZT ceramic volume fraction improve the pyroelectric coefficient of the composite. On Pyroelectric coefficient and the figure of merit, a little inflection caused by glass point(Tg) of PVA appeared. The degree of inflection is proportioned to the amount of PVA.

• Journal of the Korean Ceramic Society
• /
• v.37 no.3
• /
• pp.280-287
• /
• 2000

Adsorption behavior and amount of phenolic resin followed silica (SiO2) formation onto silicon nitride(Si3N4) surface were investigated using electrokinetic sonic amplitude (ESA) technique and with UV spectrometer, to fabricate Si3N4/SiC nano-composite based on reaction between SiO2 formed and phenolic resin absorbed onto Si3N4 particle. The amount of SiO2 formed and carbon from phenolic resin absorbed onto Si3N4 surface were calculated quantitatively to adjust the reaction between SiO2 and phenolic resin, resulting in no residual SiO2 and carbon. As a result, pre-heated tempeature for optimized reaction was below 25$0^{\circ}C$, in which there was no residual SiO2 and carbon.

• Journal of the Korean Ceramic Society
• /
• v.25 no.2
• /
• pp.125-130
• /
• 1988

The characteristics of the PZT/PMM and PZT/Butadiene composites with 3 dimensional network structure have been investigated as a function of the PZT volume fraction. The dielectric constants of the PZT composites increased linearly as the PZT volume fraction increased. However, they are not significantly affected by the polymer compliance. The piezoelectric d33 coefficients of the PZT/Butadiene are largest than the PZT/PMM because of the high elastic compliance which promotes stress transfer. The values of the mechanical quality factor adn frequency factor of the PZT/PMM composite are slightly larger, while the planar coupling factor is smaller, than the PZT/Butadiene composite. These results are due to strong interaction and mechanical coupling between PZT and PMM.