• Korean Journal of Materials Research
• /
• v.25 no.10
• /
• pp.509-515
• /
• 2015

MAO ceramic coatings were prepared on AZ61 magnesium alloy for various processing times ranging from 5 to 60 min, in an electrolyte solution based on silicate-fluoride. The mechanical, electrochemical and, microstructural properties and the phase compositions of the coating layers were investigated. In this work, unlike previous studies, coatings with high amounts of the $Mag_2SiO_4$ phase were formed which contained small amounts of MgO and $MgF_2$ at a processing condition of 30 min. A microstructural analysis revealed that the porosity of the coatings was reduced considerably with an increase in the processing time, together with a change in the pore geometry from an irregular to a spherical shape. Potentiodynamic polarization and mechanical testing results showed that the coatings acquired after a processing time of 30 min were superior to all of the others.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.117-120
• /
• 1999

The relationship between the DC degradation characteristics of the ZnO varistor and the ambient sintering-process is investigated in this study. ZnO varistors made of Matsuoka's composition were fabricated by standard ceramic techniques. The ambient sintering-process is performed at the extraordinary electrical-furnace which is equipped with the vacuum system. The Gas of sintering process was oxygen, nitrogen, argon, air respectively. The microstructure of ZnO varistors be made use of SEM equipment. The condition of DC degradation tests were conducted at $115\pm2^{\circ}C$ for periods up to 13 h. Current-voltage analysis is used to determine nonlinear coefficients($\alpha$). Resistance-frequency and capacitance-frequency analysis are accomplished to the understanding of electrical properties as DC degradation test. From above analysis, it is found that the ZnO varistor sintered in oxygen atmosphere showed superior properties at the DC degradation test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.189-193
• /
• 1997

(S $r_{0.85}$/C $a_{0.15}$)Ti $O_3$(SCT) thin films at various deposition temperature and rf power were grown by rf magnetron sputtering method on optimized Pt-based electrodes (Pt/TiN/ $SiO_2$/Si). The crystallinity of the films increases with increasing deposition temperature. SCT thin film is depend on the surface morphology and crystallinity of Pt films for bottom electrode. Dielectric constant of (S $r_{0.85}$C $a_{0.15}$)Ti $O_3$ thin films deposited on Si wafer substrate are larger with the increase of deposition temperature and gain size.in size.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.347-349
• /
• 1997

In order to investigate CO sensing property of a SnO$_2$-WO$_3$composite ceramic. we prepared pure SnO$_2$and WO$_3$added SnO$_2$compostie ceramics. Using XRD and SEM, a phase analysis and microstructure were investigated. The resistances as a function of gas atmosphere were measured by High Voltage Measure/source Unit. The measured 1000ppm CO gas sensitivity of SnO$_2$-WO$_3$composite ceramics were smaller than that of pure SnO$_2$.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.1
• /
• pp.20-23
• /
• 2014

Dual phase steels have a microstructure comprising of a polygonal ferrite matrix together with dispersed islands of martensite. There are clear differences between the image quality (IQ) map of the dual phase and the corresponding ferritic/pearlitic structures, both in the as-heat treated and cold rolled conditions. Electron backscatter diffraction (EBSD) techniques were used to study the evolution substructure of steel due to plastic deformation. The martensite-ferrite and ferrite-pearlite interfaces were observed. The interface can be a source of mobile dislocations which the bands seem to originate from the martensite islands. In particular, the use of image quality is highlighted.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.608-609
• /
• 2006

The deformation behavior under three-point bend test was found to depend on the loading uniformity and the macrostructure for SiC reticulated porous ceramics (RPCs). However, this dependence of loading uniformity is alleviated by improved macrostructure with fewer flaws and clogged pores. Even, this dependence becomes less important as the struts become thicker and stronger. The bend result of RPCs with highly uniform macrostructure is in excellent agreement with the GA (Gibson and Ashby) model, but the one with un-uniform macrostructure deviates from the GA model, suggesting that the macrostructure plays an important role in deformation behavior of RPCs under bend.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.204-207
• /
• 2000

In this paper, we have studied the effect of doped with B-Bi-Zn on properties (microstructure, density, shrinkage, permeability as a function of frequency, etc.) of hexagonal-ferrite for high frequency chip-inductor material about several GHz. The permeability were analyzed by impedance analyzer(100 kHz~40 MHz) and network analyzer(30 MHz~3 GHZ). As a result of the characteristics, the B-Bi-Zn glass ceramic was used to lower the sintering temperature for additive as a function of frequency from 100 kHz to 1.8 GHz showed constant tends. The maximum imaginary value of complex permeability was observed near the resonance frequency of 2 GHz.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.286-293
• /
• 2002

Microstructure and the electrical porperties of a ZnO-based multilayered chip-type varistor(abbreviated as MLV) with Ag/Pd(7:3) inner electrode have been studied as a function of firing of temperature. At 1100$^{\circ}$C, inner electrode layers began to show nonuniform thickness and small voids, which resulted in significant disappearance of the electrode pattern and delamination at 1100$^{\circ}$C. MLVs fired at 950$^{\circ}$C showed large degradation in leakage current, probably due to incomplete redistribution of liquid and transition metal elements in pyrochlore phase decomposition. Those fired at 1100$^{\circ}$C and above, on the other hand, revealed poor varistor characteristics and their reproductibility, which are though to stem from the deformation of inner electrode pattern, the reaction between electrode materials and ZnO-based ceramics, and the volatilization of $Bi_2O_3$. Throughout the firing temperature range of 950∼1100$^{\circ}$C, capacitance and leakage current increased while breakdown voltage and peak current decreased with the increase of firing temperature, but nonlinear coefficient and clamping ratio kept almost constant at ∼30 and 1.4, respectively. In particular, those fired between 1000$^{\circ}$C and 1050$^{\circ}$C showed stable varistor characteristics with high reproducibility. It seems that Ag/Pd(7:3) alloy is one of the electrode materials applicable to most ZnO-based MLVs incorporating with $Bi_2O_3$ when cofired up to 1050$^{\circ}$C.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.994-1000
• /
• 2002

Oxygen permeability and the mechanical properties of mixed ionic-electronic conductive $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_{3-{\delta}}$ perovskite-type membrane, fabricated by solid state reaction, were investigated with regard to microstructure. The microstructure of the membrane was controlled by changing the sintering temperature and holding time. The average grain size and relative density were evaluated as a function of sintering conditions. As the fraction of grain boundary decreased, oxygen permeability showed a tendency to increase. Especially the maximum oxygen flux of 0.37 ml/$cm^2$${\cdot}$min was measured for the specimen sintered at 1300${\circ}C$ for 10 h, which has high density and relatively large grain size. Fracture strength was dependent on the relative density of sintered body, while fracture toughness increased with average grain size.

• Journal of the Korean Ceramic Society
• /
• v.41 no.10 s.269
• /
• pp.728-734
• /
• 2004

The effect of microstructure of WC-Co substrates which have different WC grain sizes from submicron to 5 $\mu$m on the diamond-substrate adhesion strength was investigated. The substrates were pre-treated by two methods : chemical etching with Murakami's solution and subsequently with $H_2SO_4$, and thermal heat-treatment. The adhesion strength was estimated by degree of peeling after Rockwell indentation. Diamond films of 20 $\mu$m thickness deposited on the heat-treated substrates showed an excellent adhesion strength at the load of 100 kg, which ascribed to the large and elongated WC grains. However, the cutting edge of insert was deformed after heat treatment and the surface morphology of heat treated substrate strongly affected on the surface roughness of the deposited diamond films. On the contrary, the diamond film of 10 $\mu$m in thickness on the chemically etched substrates of average WC grain size over 2 $\mu$m showed good adhesion strength enough not to peel-off under a load of 60 kg. Especially, the substrate of average WC grain size over 5 $\mu$m exhibited much improved reliability of adhesion comparing with the substrate of average grain size under 2 $\mu$m. No substrate deformation was observed in this case after the chemical etching, which is more advantageous and more practical in terms of precious machining than the heat treatment case.