• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.380-384
• /
• 2003

The effects of the mole concentrations of precursor solution on the microstructure and dielectric properties of sol-gel deposited $Ba_{0.85}$S $r_{0.15}$Ti $O_3$(BST) thin films have been investigated. The films were of single perovskite phase with strong (100) preferred orientation when grown on LaNi0$_3$ buffered Pt/Ti/ $SiO_2$Si substrates using a diluted precursor solution. Variation of the precursor solution concentration resulted in a different microstructure and, in turn, affected the tunability of the sol-gel deposited films. It was observed that leakage currents increased asymmetrically for the negative and positive bias voltage with decreasing thickness. Overall results suggest that those BST films have acceptable properties f3r applications as room-temperature tunable elements.

• Journal of the Korean Ceramic Society
• /
• v.19 no.2
• /
• pp.145-151
• /
• 1982

Many materials such as silica gel, metallic oxide, activated alumina and alkaline earth metal carbonates were employed as filter media for gaseous oxides of ruthenium volatilized during high level radioactive waste processing. The adsorption efficiency of ruthenium on these materials was evaluated. For the purpose of observing behavior of ruthenium oxides, thermogravimetric analysis of ruthenium oxide in a stream of oxygen was carried out. The rate of volatilization was proportional to the square root of oxygen partial pressure, and increased exponentially with temperature. At $650^{\circ}C$, gaseous ruthenium oxides showed a strongly marked effect of deposition. Of all the materials available, calcium oxide proved to be the best that could be used to adsorb ruthenium.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.294-302
• /
• 1998

$Pb_{1+x}$($Fe_{0.5}$$Nb_{0.5}$)$O_3$ films have been synthesized on Pt/Ti/$SiO_2$/Si substrates using rfmagnetron sputtering Concentration of Fe and Nb in the deposited films was adjusted to near stoichiometry through the control of target composition, Films deposited with adjusted to near stoichiometry showed better electrical properties such as dielectic and leakage characteristics. Crystallinity and dielectric constant increased with increasing excess PbO upto 9 mol% This study also showed that dielectric constant and leakage current characteristics improved by optimum content of $O_2$ flow during deposition.

• Journal of the Korean Ceramic Society
• /
• v.38 no.4
• /
• pp.388-392
• /
• 2001

저압 화학증착법으로 등방성 흑연 기판 위에 탄화규소 증착층을 제조하였다. 반응관 내부의 전체 반응압력(이하 반응압력)을 1.5torr-100torr로 변화시켜 증착층의 미세구조에 미치는 영향을 조사하였다. 120$0^{\circ}C$ 이하에서는 전체 반응압력 변화에 상관없이 일정하게 낮은 증착속도를 보였으며, 미세구조는 round-top 구조를 나타내었다. 125$0^{\circ}C$, 10torr를 기준으로 증착온도와 반응압력이 증가함에 따라 미세구조가 round-top 구조에서 angular, faceted 구조로 변하였으며, 이는 반응압력이 증가함에 따라 증착기구가 표면반응에서 물질전달로 전이하였기 때문이다.

• Journal of the Korean Ceramic Society
• /
• v.29 no.9
• /
• pp.681-688
• /
• 1992

Ultrafine Si3N4 and Si3N4+SiC mixed powders were synthesized through thermal plasma chemical vapor deposition(CVD) using a hybrid plasma, which was characterized by the supersposition of a radio-frequency plasma and arc jet. The reactant SiCl4 was injected into an arc jet and completely decomposed in a hybrid plasma, and the second reactant CH4 and/or NH3 mixed with H2 were injected into the tail flame through double stage ring slits. In the case of ultrafine Si3N4 powder synthesis, reaction efficiency increased significantly by double stage injection compared to single stage one, although crystallizing behaviors depended upon injection speed of reactive quenching gas (NH3+N2) and injection method. For the preparation of Si2N4+SiC mixed powders, N/C composition ratio could be controlled by regulating the injection speed of NH3 and/or CH4 reactant and H2 quenching gas mixtures as well as by adjusting the reaction space.

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1123-1132
• /
• 1994

Bi-Sr-Ca-Cu-O superconductor thin films were prepared on MgO and LaAlO3 substrates by MOCVD technique. The films deposited on MgO and LaAlO3 substrates became superconducting at 64 K and 70 K respectively. The measured critical current density of thin film deposited on LaAlO3 substrate was around 104 A/$\textrm{cm}^2$. After annealing at $700^{\circ}C$ for 3 hours, the critical transition temperature(Tc) of films deposited on LaAlO3 was changed from 70 K to 74 K.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.731-738
• /
• 1994

TiN films were deposited on high speed steels by plasma assisted chemical vapor deposition (PACVD), cathode arc ion plating (CAIP) and reactive magnetron sputtering (RMS). The properties of the films deposited by the three different methods were compared. The preferred oriented plane of PACVD-TiN is (200) and those of CAIP-TiN and RMS-TiN are (111). PACVD-TiN shows a dome surface and a microstructure having small grains. CAIP-TiN shows the highest microhardness and the best adhesion strength of the three because it has a dense microstructure and an ill-defined interface. But is shows the greatest surface roughness due to the Ti droplet created by the arc. RMS-TiN shows a microstructure having large voids so that its properties in microhardness and adhesion are the worst of the three.

• Journal of the Korean Ceramic Society
• /
• v.32 no.6
• /
• pp.669-676
• /
• 1995

In this study, EO glass films were deposited by R.F. magnetron sputtering using EO glass target. The glass formation of the EO film was greatly dependent on the substrate temperature and the crystallization started at approximately 28$0^{\circ}C$. As the temperature of the substrate or the oxygen content in the sputtering gas increased, UV/VIS/NIR absorption edge moved toward longer wavelength. A wave guiding phenomenon was observed from the prism-coupler experiment and a fluorescence of 1.06${\mu}{\textrm}{m}$ originated from 4Fe3/2longrightarrow4I11/2 transition of Nd3+ was detected from the film containing Nd3+ ions.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.33-37
• /
• 2017

Single phase niobium nitride (NbN) coatings were deposited using asymmetric bipolar pulsed dc sputtering by varying pulse frequency and duty cycle of pulsed plasmas. Crystal structure, microstructure, morphology and mechanical properties were examined using XRD, FE-SEM, AFM and nanoindentation. Upon increasing pulse frequencies and decreasing duty cycles, the coating morphology was changed from a pyramidal-shaped columnar structure to a round-shaped dense structure with finer grains. Asymmetric bipolar pulsed dc sputtered NbN coatings deposited at pulse frequency of 25 kHz is characterized by higher hardness up to 17.4 GPa, elastic modulus up to 193.9 GPa, residual compressive stress and a smaller grain size down to 27.5 nm compared with dc sputtered NbN coatings at pulse frequency of 0 kHz. The results suggest that the asymmetric bipolar pulsed dc sputtering technique is very beneficial to reactive deposition of transition-metal nitrides such as NbN coatings.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.37-44
• /
• 1995

TiO2 fine powders were synthesized using oxygenolysis and hydrolysis reaction of TiCl4 vapor in gas phase. The TiO2 powder synthesized showed morphological differences depending on reaction system as follows: TiCl4-O2 reaction system produced the monosized particles having polyhedral shape with well-defined crystal planes and the particles did not agglomerate into secondary particles. TiCl4-H2O reaction system, whereas, produced the spherical secondary particles which consisted of fine primary particles. Other powder characteristics such as particle size, impurity content and rutile content are also reported in this study.