• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.44-50
• /
• 2002

The connecting rod big-end bearing is one of the most heavily loaded components of the lubrication system of high-speed combustion engines. The supply oil flow has to pass to the main bearing and the rotating crankshaft before entering the connecting rod bearing. It is common knowledge that the centrifugal forces due to the crankshaft rotation influence the oil flow to connecting rod bearing through the oil supply bore, especially, when the oil supply system to the connecting rod bearing has a 180$^{\circ}$circumferential groove via a single drilling in the crankshaft. In this case, it should be confirmed that the groove oil pressure in the main bearing is sufficient to overcome these centrifugal forces. For the purpose, the dynamic oil pressure before entering oil supply bore to the connecting rod bearing was measured instead of averaged oil pressure in main gallery. Experimental test results show that the dynamic oil pressure in the oil groove was more useful than that of main gallery. And it was also found that the oil pressure fluctuation in the groove was sensitively affected by the reduction of the main bearing clearance.

• 한국가시화정보학회지
• /
• 제12권1호
• /
• pp.43-48
• /
• 2014

This paper describes the measurement of performance evaluation of rotational flow varying chamber size and Reynolds number. Through the experimental visualization of the flow rotation, the number and position of flow rotation in the $2{\times}2$ microfluidic centrifuge were examined. At a chamber width of 250${\mu}m$, single flow rotation was obtained over at a Reynolds number of 300, while at a chamber width of 500 ${\mu}m$, single flow rotation did not appear. For performance evaluation, the intensity in microchamber was measured during 20 sec. At a chamber width of 250 ${\mu}m$, performance of rotational flow increased as Reynolds number increased. However, the variation of intensity in microchamber remained unchanged at a chamber width of 500 ${\mu}m$. The numerical analysis showed that the threshold centrifugal acceleration to obtain rotational flow for ejected particles was 200g.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.749-752
• /
• 2002

In this study, we carried out the finite element analysis about screw that is the weakest part of the centrifuge for sewage management. Structural analysis was done with respect to the change of outer radius and thickness of screw blade and screw with sewage discharge hole. If the area of circular hole is equal to that of extended holes, maximum equivalent stress was compared between hole and extended hole. Centrifugal force on account of rotation of 4000 rpm was applied the screw. The results are as follows : 1 . When the larger radius and thickness of screw blade was used, the higher maximum equivalent stress is occurred. 2. When the larger radius of sewage discharge hale was used, the higher maximum equivalent stress is occurred. 3. When the longer parallel part length of extended hole was used, the higher maximum equivalent stress is occurred. 4. If the extended hole with the same discharging area which circular hole uses, the maximum equivalent stress is lower.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2009년도 학술발표회 초록집
• /
• pp.810-814
• /
• 2009

Two dimensional steady and unsteady numerical models are applied to bend reaches of the Lower Han River and the superelevation at the Ichon-Banpo bend area of Han River was observed. The flow characteristics in the meandering river are complicated due to the effects of the centrifugal force. The centrifugal force makes the outside water surface level increase and the outside velocity decrease. To study this complex flow studying two dimensional flow is important and useful to design flood control countermeasures, the analysis of sedimentation and the site selection of intake structures. Especially, the superelevation between inside and outside of the bend should be considered to determine the height of embankment. In this study, the water surface elevations in both bank sides of the bend were measured in two reaches during floods in 2007 and 2008. And then the two-dimensional simulation using RMA-2 model was carried out. The upstream and downstream boundary conditions on bend reaches were determined by FLDWAV which is one-dimensional unsteady model. Finally, the observed data are compared with simulation results and the results of the several superelevation formulas, and the flow characteristics of the bend are discussed.

• 한국유체기계학회 논문집
• /
• 제9권2호
• /
• pp.30-38
• /
• 2006

An aerodynamic design for centrifugal compressor which was applied to medium speed diesel engine has been done. First of all, exact compressor specifications must be defined by accurate engine system matching. This matching program has been developed. Using the meanline prediction method, geometric design and performance curves for compressor were established and verified by comparing three dimensional viscous CFD results. The deviation at the design point was about 2.3%. Combustor has been designed and manufactured for the performance test of medium speed diesel engine turbocharger. Fuel nozzle of combustor was designed and its characteristics was analyzed by PIV and PDPA test equipment. Through these results, spray characteristics were studied and flow coefficient equation was deduced.

• 동력기계공학회지
• /
• 제8권2호
• /
• pp.31-38
• /
• 2004

The main purpose of this study is to investigate the characteristics of hybrid collection system combined with centrifugal force of cyclone and filtration of bag filter in one unit system. The experiment and numerical simulation are executed for the analysis of collection efficiency and pressure drop characteristics of hybrid system in comparison with those of a general fabric bag filter with the various experimental parameters such as inlet velocity(filtration velocity), dust concentration and dust type, etc.. In present system, dust particles tangentially coming into the system body are controlled by the centrifugal force effect, and the next collection is made out by the filtration mechanism in the fabric filter media. Therefore, the effective first collection causes the decrease of dust loading on the fabric filter, and it presents quite a lower pressure drop of fabric filter than that of a general fabric filter. At the inlet velocity, $21{\sim}27m/sec$ and inlet concentration(fly ash) $300mg/m^3$, pressure drops through the filter media of hybrid system are shown lower as $10{\sim}22mmH_2O$ comparing to those($17{\sim}33mmH_2O$) of a general fabric bag filter.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3287-3296
• /
• 1994

For the numerical computation of three-dimensional compressible flow field within a blade row in a centrifugal compressor, a quasi 3-dimensional solver which combines a reversible B-B flow and an irreversible H-S flow using finite element methods was developed. In a reversible B-B flow, the governing coordinates are modified in order to be applied to any type of turbomachinery, and two kinds of stream functions are introduced in order to make the Kutta condition exactly satisfied. In an irreversible H-S flow, the changes of entropy in the irreversible governing equations are determined not by empirical source but by the theoretical treatment of dissipation forces. The dissipation forces are obtained from the distribution of shear stresses in the flow passage which are given from the wall shear stresses using the exponential functions. A more accurate quasi-3-dimensional solver is established where the effect of body forces is involved in the non-axisymmetric H-S flow. Some numerical results obtained from authors' previous studies for axial flow machines assure that the present method is able to predict well as long as the flow is subsonic and not under strong viscous effect.

• 한국기계가공학회지
• /
• 제16권2호
• /
• pp.34-43
• /
• 2017

Large amounts of household water are required as common households change from the single-residence types of the past to group-residence types. Therefore, the management of reservoirs is urgently required to ensure the supply of clean household water to users. Important considerations for household water include the duration for which the water is stored in the reservoir, the disinfectant's dilution capacity, and the size of the reservoir to allow for the amount of water required for emergencies and firefighting. The drainage efficiency was analyzed in this study using computational fluid analysis for existing rectangular reservoirs and the newly proposed hexagonal reservoir. Thus, it was determined that the centrifugal force generated at the inlet was maintained until the outlet due to the approximately circular shape of the hexagonal reservoir. The findings of this study verified that the centrifugal force improved the flow rate by approximately 35% compared to existing rectangular reservoirs and that drainage was performed efficiently without stagnation zone.

• 한국생산제조학회지
• /
• 제19권5호
• /
• pp.609-615
• /
• 2010

Angular contact ball bearings in a high speed spindles are under the extreme conditions, such as high temperature, big centrifugal force and thrust cutting forces. So, the assembly contacts between spindle shaft and inner ring bearings, bearing housing and outer ring of bearings are occasionally unstable at high speed revolution. Furthermore, the ball contact angle of a bearing, which influence stiffness and lifetime of bearings, are changed according to loads and rotational speed. To analyze internal forces of a bearing under high speed revolution, the ball contact are calculated using nonlinear equations in consideration of rotational speed, thrust loads and raceway form. Diameter increase of inner and outer ring by influence factors, such as internal forces to inner and outer ring, centrifugal force and temperature of inner and outer rings are calculated to establish stable state in bearing assembly in high speed spindle. Finally, contribution ratio of influence factor to assembly design tolerance of inner and outer rings are shown and the stable assembly design tolerance are proposed.

• 대한기계학회논문집B
• /
• 제38권2호
• /
• pp.147-153
• /
• 2014

본 연구는 폐수처리용 원심 펌프 설계과정에서 수행하는 3차원 유동해석에 있어서 표면 거칠기를 고려한 해석 결과와 고려하지 않은 해석 결과가 성능 예측에 미치는 영향을 살펴보고자 수행하였다. 이를 위해 비교적 기하학적 형상이 복잡한 폐수처리용 원심펌프의 표면 거칠기 변화가 유동 해석 결과에 미치는 영향을 평가하였다. 그리고 실제 해석 대상 펌프를 사용한 실험 결과 값과 해석 결과 값을 서로 비교 해봄으로써 표면 거칠기를 고려한 펌프의 해석 값과 고려하지 않은 해석 결과 값 차이에 대한 정량적인 분석을 제시하였다. 그 결과, 해석 시 표면 거칠기를 고려한 해석결과는 실험결과와 잘 일치하는 함을 보였으며, 표면 거칠기는 펌프의 성능해석에 약 7% 범위에서 영향을 준다는 것을 확인할 수 있었다.