• The KSFM Journal of Fluid Machinery
• /
• v.11 no.2
• /
• pp.38-45
• /
• 2008

This study presents a numerical procedure to optimize the compressor design to increase the surge margin of compressor with response surface method (RSM). The Box-Behnken design method is used to reduce the number of calculation for fitting the second-order response surface. In order to consider the increase of surge margin during numerical optimization without any calculation at the surge point, the slope of compressor characteristic curve at the design point is suggested as an objective function in the present optimization problem. Mean line performance analysis method is used to get the design and off-design characteristic curves of centrifugal compressor. The impeller exit angle, impeller exit height and impeller radius are chosen as design variables. The optimum shapes show the increase of surge margin for the surge margin optimization and increase of efficiency for the efficiency optimization in comparison with an initial shape.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.104-107
• /
• 2006

For the practical application on SCFCL(Superconducting fault current limiters), Bi-2212 tubes were fabricated by Centrifugal Forming Process(CFP). The tubes were annealed at 830, 840, $850^{\circ}C$, respectively for 80 hours in oxygen atmosphere. The tubes heat treated at $840^{\circ}C$ demonstrated better electric characteristics than the tubes heat treated at 830 and $850^{\circ}C$. The typical value measured at 77 K in the self field was around 556 A. In terms of cooling effect on superconducting properties, it was found the electrical properties were quite dependent on the mold design and shapes. In order to check uniformity along the tube, EFDLab fur heat and fluid analysis of NIKA was adopted. It was found out that the simulation data was quite well matched with experimental results.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.04a
• /
• pp.111-114
• /
• 2009

Production of rolled steel has been growing partly supported by the advancement of rolls and rolling mills. Aiming at the further improvement in roll performance, various new techniques such as centrifugal casting, double poured casting cast steel, special build-up making, etc. have been introduced in the field of roll manufacture in these several years. The present paper describes the development of horizontal cast rolls(sleeve and indefinite chilled roll) made by Hyundai Steel and the results of mill tests. The developed roils are contributing the improvement of final products.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.451-452
• /
• 2006

According to the demand of high productivity, the interest of manufacturing skills is growing in the industrial society. Especially the long spindle becomes important these days. The rotating accuracy of the spindle concerns the centrifugal force. In detail explaining, it is influenced by the speed of the spindle. In this study, we would show changes of the distance caused by a rotating speed of the spindle using a software, $ADAMS^{(R)}$. And because of the gravity of the spindle's mass, we would find the static droop of the long spindle.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.2 s.95
• /
• pp.129-134
• /
• 2005

This paper describes the influence of geometric parameters on the noise generation from a centrifugal compressor. From the analysis of noise measurements, it is observed that Blade Passing Frequency noise related to the rotating impeller is more important, and it is focused on the comparison of this discrete frequency noise according to the shape change. Navier-Stokes solver is used to simulate the flow-field of the impeller and the vaned diffuser, and time-dependent pressure data are calculated and Fourier-transformed to perform the near-field noise prediction. The effects of various geometry design variables such as the gap between the impeller and the diffuser, impeller shape variations on the near-field noise distribution are investigated.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.963-970
• /
• 2000

The turbo chiller uses centrifugal compressor, which operates at about 14,500 rpm. Due to the high rpm of the impeller, the noise of chiller males one of the serious problems. The possibility of the sound reduction by using absorbing material is studied in this paper. The generated sound propagates through the duct and then radiates to the outer field. So, the use of sound absorption material inside the duct is one of the effective methods. To study the effect of location of the material, we use Boundary Element Method to analyze the sound field inside the duct system. Numerical study shows the highest sound pressure region is near the elbow of curved duct. From the numerical study, it is also shown that appropriate use of sound absorbing material at this region makes 8dB reduction of the highest noise level.

• Journal of Mechanical Science and Technology
• /
• v.15 no.9
• /
• pp.1292-1301
• /
• 2001

The mean-line method using empirical models is the most practical method of predicting off-design performance. To gain insight into the empirical models, the influence of empirical models on the performance prediction results is investigated. We found that, in the two-zone model, the secondary flow mass fraction has a considerable effect at high mass flow-rates on the performance prediction curves. In the TEIS model, the first element changes the slope of the performance curves as well as the stable operating range. The second element makes the performance curves move up and down as it increases or decreases. It is also discovered that the slip factor affects pressure ratio, but it has little effect on efficiency. Finally, this study reveals that the skin friction coefficient has significant effect on both the pressure ratio curve and the efficiency curve. These results show the limitations of the present empirical models, and more resonable empirical models are reeded.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.4
• /
• pp.36-41
• /
• 2015

The cyclone separator is a simple device, which causes the centrifugal separation of materials such as droplets or particles in a fluid stream. The cyclone separator utilizes the energy obtained from fluid pressure and linear motion to create rotational fluid motion. This rotational motion leads the materials suspended in the fluid to separate from the fluid quickly due to the centrifugal force. The rotation is produced by the tangential or involuted introduction of fluid into the vessel. These materials may be droplets of fuel in blow-by gas through an engine. Droplets suspended in the feed liquid may separate according to size, shape, or density. And the change of part dimension in a cyclone separator can yield the its performance variation. The current study shows the influence of design parameters on the performance of a cyclone separator for blow-by gas.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.443-446
• /
• 2002

A vehicle oversteered or cornering at excessive speed leaves tire yaw mark on the road surface. A yaw mark is a sign that the tire was sideslipping and exceeded its frictional limit because of centrifugal force. Problems exist with the traditional equation, “critical speed formula (CSF)”, that limits its practical use in traffic accident reconstruction. A major problem is that the equation dose not account for vehicle dynamics and interface between tire and road. The literature refers to that the accuracy of the critical speed formula varies with several factors. New equations that account for vehicle dynamics are introduced in this paper. A comparison of the accuracy of the new method and the traditional method in the calculation of speed is conducted.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.416-421
• /
• 2011

Recently there has been increase in need for high precision and high speed machining due to economic and environmental reasons. It is a very important issue that determines the optimal preload that is to be applied to bearings in order to satisfy the performance required in bearings according to its operation conditions. This study introduces a variable preload device that can automatically adjust the preload applied in a machine tool spindle using centrifugal force as opposed in existing rubber instrument. In this study, the deformation of the rubber device by the centrifugal force is analyzed and it is discussed that the proposed device can be worked properly through changes of the collar density.