• Advances in concrete construction
• /
• 제8권4호
• /
• pp.305-309
• /
• 2019

Pervious concrete pavements are the need of the day to avoid urban flooding and to facilitate ground water recharge. However, the strength of pervious or porous concrete is considerably less compared to conventional concrete. In this experimental investigation, an effort is made to improve the strength of pervious concrete by adopting fibres and a small amount of fine aggregate. A porous concrete with cement to aggregate ratio of 1:5 and a water-powder ratio of 0.4 is adopted. 30% of the cement is replaced by cementitious material ground granulated blast furnace slag (GGBS) for better strength and workability. Recron fibres at a dosage of 0.5, 1.0 and 1.5% by weight of cement were included to improve the impact strength. Since concrete pavements are subjected to impact loads, the impact strength was also calculated by "Drop ball method" in addition to compressive strength. The effect of fine aggregate and recron fibres on workability, porosity, compressive and impact strength was studied. The investigations have shown that 20% inclusion of fine aggregate and 1.5% recron fibres by weight of cement give better strength with an acceptable range of porosity.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.78-79
• /
• 2013

A policy for recycling waste concrete has been extensively studied, but it is still lacking to recycle and reuse as a cementitious powder, and the property has big different depending on the aggregate rates. In this study, the amount of cement powder according to the internal properties of the aggregate were mixed. From as a result, Concrete Powder to play inside the aggregate composition of the cement composition CaO rigs that causes loss of power and strength reduction due to rising real water cement ratio will affect large.

• 한국건축시공학회지
• /
• 제15권2호
• /
• pp.169-175
• /
• 2015

본 연구는 콘크리트 마감재로써 골재노출 콘크리트를 개발하기 위한 일련의 실험이다. 실험변수로는 고강도 및 일반강도의 물-시멘트비별 당류계 지연제의 살포량 및 세척시기 변화가 물씻기 공법을 이용한 골재노출 콘크리트의 품질에 미치는 영향을 분석하였다. 그 결과, 물-시멘트비 25%는 세척시점 0.75일, 물-시멘트비 35%와 55%는 1일, 65%는 1.5일에 당류계 지연제를 $24m{\ell}/m^2$ 살포하였을 때 가장 효과적이며 양호한 골재 노출의 표면이 연출되는 것을 확인할 수 있었다.

• 자원리싸이클링
• /
• 제15권2호
• /
• pp.24-31
• /
• 2006

폐콘크리트 파쇄시 발생하는 재생잔골재의 품질을 검토하였으며, 재생잔골재를 활용한 모르타르의 압축강도, 휨강도 및 흡수율을 검토하였다. 또한, 프리캐스트 콘크리트 제품용 골재로서의 적용성에 대하여 평가하였다. 재생잔골재의 밀도 및 흡수율은 각각 $2.31\;g/cm^3$ 및 8.07%로 KS F 2573의 2종에 해당되는 품질이었다. 혼합시멘트 MRS1, MRS2 및 MRS3 사용 모르타르의 재령 28일 압축강도는 물-시멘트비 35%, 양생온도 $40^{\circ}C$의 조건에서 각각 15.8, 27.4 및 48.7MPa로 최대값을 발현하였다. 모르타르의 최대휨강도는 혼합시멘트 MRS1 및 MRS2 사용시 물-시멘트비 35.0%, 양생온도 $40^{\circ}C$, 혼합시멘트 MRS3사용시 물-시멘트비 37.5%, 양생온도 $40^{\circ}C$의 조건에서 발현하였다. 혼합시멘트 MRS1, MRS2 및 MRS3를 사용한 모르타르의 흡수율의 범위는 각각 $8.3{\sim}7.3%,\;6.5{\sim}8.5%$ 및 $3.5{\sim}6%$의 범위로 나타났다. 그러므로 혼합시멘트와 재생잔골재의 비율을 적절히 조절함으로써 MRS1는 저강도용, MRS2는 보통강도용, MRS3는 고강도용으로 다양한 프리캐스트 콘크리트 제품에 적용될 수 있을 것으로 기대된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 봄 학술발표회 논문집
• /
• pp.202-207
• /
• 1996

Recently, the mortar crack on floor is very serious in construction field, e.g. the crack due to plastic shrinkage and the crack due to drying shrinkage. To prevent this kind of crack, optimum mix propertions not only satisfying the required workability but also minimizing the unit water content were selected. And the expansion admixtures were used to compensate the shrinkage of mortar. This study shows that water/cement ratio used in construction field is about 64%. Even if we reduce water/cement ratio of mortar by the appropriate use the fine aggregate with high fineness modulus and superplastizer, floor mortar can have the required workability. The equations between mortar flow and water/cement ratio, sand/cement ratio, fineness modulus of fine aggregate were proposed in this study. And this equation may provide available mix proportions of floor mortar.

• 콘크리트학회논문집
• /
• 제13권4호
• /
• pp.305-313
• /
• 2001

본 연구에서는 콘크리트 열전도율의 영향인자에 대하여 TLPP원리를 응용한 QTM-D3 장비를 이용하여 실험을 실시하였고, 이들 실험결과를 이용하여 콘크리트의 열전도율을 예측하는 모델식을 제안하였다. 본 연구를 통하여 얻은 결론은 다음과 같다. 콘크리트, 모르타르 및 페이스트의 열전도율에 미치는 주요 영향인자를 구명하기 위해 본 연구에서 선택된 실험변수는 재령, 골재 함유량, 시멘트 함유량, 결합재 종류, 잔골재율, 시편의 온도 및 함수상태로 총 7가지이다. 이중에서 골재 함유량과 함수상태가 콘크리트 열전도율의 주요 영향인자임을 알 수 있었다. 그리고 시멘트 사용량이 많은 페이스트나 모르타르의 경우 시멘트 함유량이나 결합재 종류에 의해서도 열전도율이 영향을 받고 있다. 그러나 재령은 콘크리트의 열전도율에 큰 영향을 미치지 않음을 알 수 있었다. 콘크리트 열전도율에 주요 영향인자인 골재 함유량, 잔골재율, 시편의 온도 및 함수상태를 이용하여 콘크리트의 열전도율을 계산할 수 있는 모델식을 제안하였다.

• 한국도로학회논문집
• /
• 제13권1호
• /
• pp.169-175
• /
• 2011

콘크리트에서 강도는 콘크리트의 물리적 특성을 평가할 수 있는 중요한 인자 중 하나이며 콘크리트에 가장 많은 부피를 차지하는 것이 골재이다. 또한 시멘트는 콘크리트 만드는 결합재로서 이 역시 강도와 매우 밀접한 관계가 있다. 이러한 골재와 시멘트의 특성이 콘크리트 압축강도와 전단파 속도의 상관관계에 미치는 영향을 파악하고자 굵은 골재 최대치수와 시멘트 종류별로 실험을 실시하였다. 시멘트는 1종 시멘트와 초속경 시멘트를 사용했고, 골재는 서로 다른 지역의 3가지 골재를 사용하였다. 골재의 입도는 굵은 골재 최대치수 19mm와 13mm의 단입도 골재를 사용하여 동일 배합시 압축강도와 전단파 속도의 상관관계를 살펴보았다. 또한 골재의 특성을 정량화 하고자 LA마모시험을 실시하였다. 그 결과 압축강도와 전단파 속도의 상관관계는 시멘트 종류에 따라 달랐으나, 골재의 종류, 입도 및 마모감량에 관계없이 일정한 상관성을 보이는 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.327-332
• /
• 2000

The objective of this study was to improve the defects of lightweight cement concrete by treating with redispersible polymer powders. The statistical relationships of water-cement ratios, contents of lightweight aggregates and polymer powers and be used for predicting the concrete strength. It was found that the varieties and techniques adopted in this experiment were capable of identifying the influence of various tested for air contents, flow test, water absorption, specific gravity, flexural and compressive strength. This study showed that fundamental properties were very affected by cement- lightweight aggregate ratio, polymer-cement ratio and water-cement ratio.

• International Journal of Concrete Structures and Materials
• /
• 제19권1E호
• /
• pp.17-23
• /
• 2007

In rainy weather, permeable concrete pavement has advantages such as good drainage, increased skid resistance, reduced splash and spray behind vehicles for improving the safety of driving vehicles as well as reduction of the traffic noise. It also contributes to improvement of traffic environment. In this study, the fundamental properties of permeable concrete in accordance with maximum size of aggregate, sand percentage and unit cement content were investigated for practical use of permeable concrete pavement. Although the permeability standard for typical permeable asphalt-concrete pavement is $1{\times}10^{-2}cm/sec$, the researchers determined that the coefficient of permeability of the permeable concrete should be set higher at $1{\times}10^{-1}cm/sec$. Then, the researchers measured the coefficient of permeability, strength, void ratio, and continuous void ratio of the permeable concrete while varying maximum size of the aggregate, sand percentage, unit cement content for detailed analysis. It was found that the void ratio, continuous void ratio, and flexural strength were about 15%, 12%, and 5.0MPa, respectively, when the permeability of the concrete was set at $1{\times}10^{-1}cm/sec$. Given that the maximum size of aggregate was $10{\sim}13mm$, we reached the conclusion that the best mix design for permeable concrete was $0{\sim}20%$ of sand percentage and $380kg/m^3$ of unit cement content.

• Advances in concrete construction
• /
• 제11권4호
• /
• pp.285-298
• /
• 2021

This study focused on experimental evaluation of mechanical properties of pervious concrete mixtures with the aim of achieving higher values of strength while considering the associated costs. The effectiveness of key parameters, including cement content, water to cement ratio (W/C), aggregate to cement ratio (A/C), and sand replacement was statistically analyzed using paired-samples t-test, Taguchi method and one-way ANOVA. Taguchi analysis determined that in general, the role of W/C was more significant in increasing strength, both compressive and flexural, than cement content and A/C. It was found that increase in replacing percent of coarse aggregate with sand could undermine specimens to percolate water, though one-way ANOVA analysis determined statistically significant increases in values of strength of mixtures. Cost analysis revealed that higher strengths did not necessarily correspond to higher costs; in addition, increasing the cement content was not an appropriate scenario to optimize both strength and cost. In order to obtain the optimal values, response surface method (RSM) was carried out. RSM optimization helped to find out that W/C of 0.40, A/C of 4.0, cement content of about 330 kg/m3 and replacing about 12% of coarse aggregate with sand could result in the best values for strength and cost while maintaining adequate permeability.