• Advances in concrete construction
• /
• v.4 no.4
• /
• pp.305-317
• /
• 2016

Porous materials such as concrete could be subjected to aggressive ions transport. Durability of cement paste is extremely depended on water and ions penetration into its interior sections. These ions transport could lead different damages depending on reactivity of ions, their concentrations and diffusion coefficients. In this paper, chloride diffusion process in cement hydrates is simulated at atomistic scale using molecular dynamics. Most important phase of cement hydrates is calcium silicate hydrate (C-S-H). Tobermorite, one of the most famous crystal analogues of C-S-H, is used as substrate in the simulation model. To conduct simulation, a nanopore is considered in the middle of simulation cell to place water molecules and aggressive ions. Different chloride salts are considered in models to find out which one is better for calculation of the transport properties. Diffusion coefficients of water molecules and chloride ions are calculated and validated with existing analytical and experimental works. There are relatively good agreements among simulation outputs and experimental results.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.438-440
• /
• 2008

Effects of Ga contents of CIGS absorber layer on the performance of thin films solar cells were investigated. As Ga content increased, the grain size of CIGS films decreased presumably because Ga diffusion during 2nd stage of co-evaporation process is more difficult than In diffusion. Performances of corresponding solar cell show systematic dependence on Ga content in which open circuit voltage increases and short circuit current and fill factor decrease as Ga contents increases. At a optimal condition of Ga/(In+Ga)=0.27, the solar cell shows a conversion efficiency of 15.6% with $V_{OC}$ of 0.625 V, $J_{SC}$ of 35.03 mA/$cm^2$ and FF of 71.3%.

• Journal of Hydrogen and New Energy
• /
• v.14 no.3
• /
• pp.195-206
• /
• 2003

Polymer electrolyte membrane fuel cells(PEMFC) are very interesting power source due to high power density, simple construction and operation at low temperature. But they have problems such as high cost, improvement of performance and effect of temperature. This problems can be approached using mathematical models which are useful tools for analysis and optimization of fuel cell performance and for heat and water management, in this paper, transient model consists of various energy terms associated with fuel cell operation using the mass and energy balance equation. And water transfer in the membrane is composed of back diffusion and electro-osmotic drag. The temperature calculated by transient model approximately agreed with the temperature measured by experiment in constant current condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.1
• /
• pp.115-121
• /
• 2008

In this paper, a three-dimensional computational fluid dynamic model of a proton exchange membrane fuel cell(PEMFC) with serpentine flow channel is presented. A steady state, single phase and isothermal numerical model has been established to investigate the influence of the GDL (Gas Diffusion Layer) parameters. The GDL is made of a porous material such as carbon cloth, carbon paper or metal wire mesh. For the simplicity, the GDL is modeled as a block of material having numerous pathways through which gaseous reactants and liquid water can pass. The porosity, permeability and thickness of the GDL, which are employed in the model parameters significantly affect the PEMFC performance at the high current region.

• Solar Energy
• /
• v.7 no.1
• /
• pp.35-41
• /
• 1987

This paper presents a comprehensive computer simulation of hydrogenated amorphous p-i-n silicon solar cells. The physical mechanism governing solar cell operation has been modeled and solved numerically by Runge-Kutta-Gill method. Effects of gap state density, dopant impurity, diffusion length and interface recombination velocity on solar cell performance are investigated. Numerical results show that the electric field in i-region is not uniform but depends strongly on voltage and position. A rather poor fill factor may be due to the electric field variation and short diffusion length. It is found out that the life time should be improved in order to increase a fill factor and a conversion efficiency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.487-490
• /
• 2011

We used X-ray tomography to carry out an experimental study to visualize the effect of freeze and thaw cycles on the gas diffusion layer (GDL) in a polymer electrolyte membrane fuel cell (PEMFC). A PEMFC has freeze and thaw cycles if the fuel cell is operating at a below-freezing ambient temperature. The cycle permanently deforms the fuel-cell capillary structures and reduces the ability of the cell to generate electric power and also reduces its service life. The GDL is the thickest capillary layer in the fuel cell, so it experiences the most deformation. The X-ray tomography facility at the Pohang Accelerator Laboratory was used to observe the structural changes in GDLs induced by a freeze and thaw cycle. We discuss the effects of these structural changes on the power production and service life of PEMFCs.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.1
• /
• pp.7-14
• /
• 2017

This study aims to examine the influences of substrates/diffusion layers (DL) and oxygen reduction reaction catalysts ($M_{ORR}$) on the performance of $M_{ORR}/IrO_2$/DL-type bifunctional oxygen electrodes for use in polymer electrolyte membrane (PEM)-type unitized regenerative fuel cells (URFC). The $M_{ORR}/IrO_2$/DL electrodes were prepared via two sequential steps: anodic electrodeposition of $IrO_2$ on various DLs and fabrication of $M_{ORR}$ layers (Pt, Pd, and Pt-Ru) by spraying on $IrO_2/DL$. Experiments using different DLs, with Pt as the $M_{ORR}$, revealed that the roughness factor of the DL mainly determined the electrode performance for both water electrolyzer (WE) and fuel cell (FC) operations, while the contributions of porosity and substrate material were insignificant. When Pt-Ru was utilized as the $M_{ORR}$ instead of Pt, WE performance was enhanced and the electrode performance was assessed by analyzing round-trip efficiencies (${\varepsilon}_{RT}$) at current densities of 0.2 and $0.4A/cm^2$. As a result, using Pt-Ru instead of Pt alone provided better ${\varepsilon}_{RT}$ at both current densities, while Pd resulted in very low ${\varepsilon}_{RT}$. Improved efficiency was related to the additional catalytic action by Ru toward ORR during WE operation.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.6
• /
• pp.17-20
• /
• 2003

This paper describes the effect of halogenic gettering during oxide passivation of commercial solar cell with the $N^{+}$-P-$N^{+}$ structure. In order to study the effect of halogenic gettering on $N^{+}$-P-$N^{+}$ structure mono-crystalline silicon solar cell, we performed conventional POCl$_3$ diffusion for emitter formation and oxide passivation in the presence of HCl vapors. The $N^{+}$-P-$N^{+}$ structure based silicon solar cells were found to have higher short circuit current and minority carrier lifetime. Their performance was also found to be superior than the conventional $N^{+}$-P-$N^{+}$ structure based mono-crystalline silicon solar cell. The cell parameters of the $n^{+}$-p-$p^{+}$ and $n^{+}$-p-$n^{+}$ structure based cells, passivated by HCl assisted oxidation were measured. The improvement in $I_{sc}$ was attributed to the effect of the increased diffusion length of minority carriers, which came from the halogenic gettering effect during the growth of passivating oxide. The presence of chlorine caused gettering of the cells by removing the heavy metals, if any. The other advantage of the presence of chlorine was the removal of the diffusion induced (in oxygen environment) stacking faults and line defects from the surfaces of the silicon wafers. All these effects caused the improvement of the minority carrier lifetime, which in-turn helped to improve the quality of the solar cells.

• Journal of Sensor Science and Technology
• /
• v.17 no.5
• /
• pp.329-337
• /
• 2008

Simple, small and portable oxygen sensors were fabricated by tape casting technique. Yttria stabilized zirconia containing cordierite ceramics (YSZC) were used as a porous diffused layer of oxygen in pumping cell. Yttria stabilized zirconia (YSZ) solid electrolyte, YSZC porous diffusion layer and heater-patterned ceramic sheets were prepared by co- firing method. Limit current characteristics and the linear relationship of current to oxygen concentration were observed. Viscosity variation of the slurries both YSZ and YSZC showed a similar behavior, but micro pores in the fired sheet were increased with increasing of the cordierite amount. Molecular diffusion was dominated due to the formation of large pores in porous diffusion layer. The plateau range of limit current in porous-type oxygen sensor was narrow than the one of aperture-type oxygen sensor. However limit current curve was appeared in porous-type oxygen sensor even at the lower applied voltage. The plateau range of limit-current was widen as increasing the thickness of porous diffusion layer of the YSZ containing cordierite. Measuring temperature of $600{\sim}650^{\circ}C$ was recommended for limit-current oxygen sensor. Porous diffusion layer-type oxygen sensor showed faster response than the aperture-type one and was stable up to 30 days running without any crack at interface between the layers.

• Journal of Environmental Health Sciences
• /
• v.42 no.1
• /
• pp.61-70
• /
• 2016

Objectives: The purpose of this study is to determine the exposure risk to tattoo components by analyzing skin absorption using the in vitro method. Tattoos are commonly used for cosmetic purposes, and the skin of not only the operator but of the people who are undergoing the cosmetic procedure is continuously exposed to hazardous chemicals. Methods: Skin permeation risk determination was conducted by the in vitro Franz diffusion cell method according to the ingredient types of tattoo dyes, such as volatile organic compounds (VOCs), non-volatile organic compounds and heavy metals, using hairless mouse full skin and human cadaver epidermis. Results: The major components with good skin penetration for each type of tattoo dye ingredient were clarified. Among the tatto dye ingredients, 1,2-Dichlorobenzene, Zn, Al, Pb and Ti showed good skin penetration. Most of the skin transmission rates were higher in hairless mouse full skin than in human cadaver epidermis. Conclusion: A possible exposure risk to hazardous substances in tattoo dyes was confirmed from this study. These results are expected to provide a positive contribution to the establishment of management regulations for tattoo dyes.