• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1823-1825
• /
• 2004

Spherically convergent beam fusion device accelerate ions, which are generated between outer anode and inner grid cathode, toward the spherical center. The collision of opposite direction ions give rise to fusion reactions. Spherically convergent beam fusion device is very simple and compact, therefore the device has a potential that is applied to a portable neutron source. An experimental device consist of a 20cm-diameter spherical mesh-type anode and 7cm-diameter open spherical grid cathode and was maintained at a constant pressure of about 1333 Pa by feeding argon gas.

• 한국전기전자재료학회논문지
• /
• 제18권8호
• /
• pp.729-733
• /
• 2005

Al electrode for OLED was deposited by FTS (Facing Targets Sputtering) system which can deposit thin films with low substrate damage. The Al thin films were deposited on the cell (LiF/EML/HTL/Bottom electrode) as a function of working gas such as Ar or Ar+kr mixed gas. Also Al thin films were prepared with working gas pressure (1, 6 mTorr). The film thickness and I-V curve of Al/cell were measured and evaluated. In the results, when Al thin films were deposited using pure Ar gas, the turn-on voltage of Al/cell was about 11 V. And using the Ar:Kr($75\%:25\%$) mixed gas, the turn-on voltage of Al/cell decreased to about 7 V.

• The Korean Journal of Ceramics
• /
• 제4권2호
• /
• pp.151-155
• /
• 1998

The total electrical conductivity, ionic conductivity, and nonstoichimetry of a new cathode material $Y_{1-x}Ca_xFeO_{3-\delta}$ (x=0.1) were measured as functions of temperature ($900\leqT/^{\circ}C\leq1100$) and oxygen partial pressure $(10^{-6}\leqPo_2/atm\leq0.21$). Isothermal variations of these properties with $Po_2$ support that the majority type of ionic defects are anti-Frenkel disorder which, however, has seldom been considered for perovskite-based oxides. The results are discussed in comparison with those reported on similar oxides.

• 한국진공학회지
• /
• 제3권4호
• /
• pp.382-388
• /
• 1994

포항가속기연구소에서 사용될 진공게이지 교정시스템이 설계 제작되었다. 이 교정시스템은 동적 교정방법으로 설계되었으며 transfer standard 로서 spinning rotor gauge를 사용하였다. 포항가속기의 저장리에 사용될 모든 진공게이지는 교정시스템으로 교정을 하여 사용할 것이며, 주로 교정할 게이지로 는 Bayard-Alpert(BA) nude ionization gauge와 cold cathode gauge등이 있다. 본 논문에서는 포항가속 기의 진공게이지 교정시스템에 대해서 소개를 하였고 현재까지 BA nude ioni-zation gauge 6대 extractor gauge 1대 high pressure gauge 1대와 cold cathode gauge 5대를 10-4에서 10-4 Torr 범위내 에서 교정하여 그 결과를 보였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1717-1719
• /
• 2000

DLC films are deposited by using an FCVA deposition system with a mirror-type magnetic field configuration. Permanent magnets and: magnetic yokes around the cathode have been observed to enhance the mobility of arc spots on the cathode and the stability of arc plasma, Effects of reactor pressures and substrate biases on structural properties of DLC films deposited are investigated. The results show that the highest $sp^{3}/sp^{2}$ fraction is obtained when the films are deposited at a pressure of $3{\times}10^4$ Torr and a bias voltage of - 50 V. The variation of the structural properties due to thermal stress up to 500$^{\circ}C$ is also examined.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.532-535
• /
• 2000

We have fabricated a sensor system for on-line monitoring the oxygen permeability and diffusivity of six different polymer films using the miniaturized 6 cathode(Ag)-single anode(Ag/AgCl) type hexagonal oxygen electrode. This system consists of multiple input front-end electronics, signal conditioning circuit using the embedded microcontroller 80C196KC, PC interface circuit and PC with the OS for microcontroller and the operating program for this system. The digital low-[ass filter was programmed and the simulated filter characteristics were enough to eliminate the noise from sensor signal. According to the experimental results, the linearity coefficients of the output voltage to oxygen partial pressure for each sensor electrode of six cathode type oxygen sensor are 0.998, 0.997, 0.998, 0.997, 0.997, 0.997 respectively, and the response times are all within 4 minutes.

• Journal of Mechanical Science and Technology
• /
• 제19권4호
• /
• pp.1018-1026
• /
• 2005

The proton exchange membrane (PEM) fuel cell system consisting of stack and balance of plant (BOP) was modeled in a MATLAB/Simulink environment. High-pressure operating (compressor type) and low-pressure operating (air blower type) fuel cell systems were con­sidered. The effects of two main operating parameters (humidity and the pressure of the supplied gas) on the power distribution characteristics of BOP and the net system efficiency of the two systems mentioned above were compared and discussed. The simulation determines an optimum condition regarding parameters such as the cathode air pressure and the relative humidity for maximum net system efficiency for the operating fuel cell systems. This study contributes to get a basic insight into the fuel cell stack and BOP component sizing. Further research using muli­object variable optimization packages and the approach developed by this study can effectively contribute to an operating strategy for the practical use of fuel cell systems for vehicles.

• 한국광학회지
• /
• 제13권6호
• /
• pp.559-563
• /
• 2002

본 논문에서는 직접 고안한 scanned point-detecting system(SPDS)을 이용하여 PDP 방전 셀 내에서 방출되는 광을 3차원 적으로 시간 분해하여 측정하였다. PM tube를 통해 검출된 광 신호를 오실로스코프 상에서 파형을 확인하고 PC제어를 통해 결과를 얻었다. Ne-Xe(4%) 혼합가스가 400 ton압력으로 채워진 패널에서 측정한 시간 분해 결과를 살펴보면 패널의 전면판(top view)에서는 방전이 cathode전극의 안쪽 edge에서 시작되면서 cathode전극 바깥쪽으로 호의 형태를 이루면서 진행되는 것을 알 수 있었으며 패널의 측면(side view)에서 측정한 시간 분해 결과를 살펴보면 약 150$\mu\textrm{m}$의 높이까지 방전에 의한 광이 검출되었다. 그리고 구동전압 펄스가 인가된 후 730 ns에서 가장 큰 intensity가 나타났다.

• 한국세라믹학회지
• /
• 제39권4호
• /
• pp.367-376
• /
• 2002

$SrZr_{1-x}Y_xO_{3-\delta}$(x=0.05, 0.10)-금속전극 계에서 임피던스법과 d.c.법으로 전기전도도를 측정함으로써 고체전해질 및 전극전도도를 고찰하였다. 고체전해질과 anode를 통한 전기전도도는 $P_W^{1/2}$(PW는 수증기분압)에 의존하여 증가함을 보였다. Cathode 전도도는 $P_{O2}^{1/4}$에 비례함을 보였으며, 수증기분압 증가와 함께 감소하여 고체전해질내의 전자 결함의 농도와 함께 증가하는 것을 알 수 있었다. 수소분위기에서는 수증기의 첨가가 anode와 cathode 두 방향의 전극반응 속도 모두를 촉진하였다. 도펀트 첨가량이 5%에서 10%로 증가될 때 anode와 고체전해질의 전기전도도가 3배 이상 크게 증가하여 유효 산소이온공공의 농도가 급격히 증가함을 알 수 있었다. Pt와 Ag전극을 통한 cathode 전도도의 활성화에너지가 거의 같은 값을 나타냈으며 이는 cathode반응의 속도가 금속전극이 아니라 고체전해질표면에서 일어나는 반응에 의하여 결정되는 것으로 해석되었다.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2017년도 추계학술논문요약집
• /
• pp.74-74
• /
• 2017

Electrorefining is a key step in pyroprocessing. The electrorefining process is generally composed of two recovery steps - the deposit of uranium onto a solid cathode and the recovery of the remaining uranium and TRU elements simultaneously by a liquid cadmium cathode. Uranium deposit recovered from the solid cathode is a dendritic powder. It is necessary to separate the adhered salt from the deposits prior to the consolidation of uranium deposit. The adhered salt is composed of lithium, potassium, uranium, and rare earth chlorides. Distillation process was employed for the cathode processing. One of the operation methods is distillation of the salt at low temperature ($900^{\circ}C$), and then melting of the deposit at high temperature to avoid a backward reaction. For the development of the salt distiller, the distillation behavior of the low vapor pressure chlorides should be studied. Rare earth chlorides in the adhered salt of uranium deposits have relatively low vapor pressures compared to the process salt (LiCl-KCl). In this study, the evaporation rates of the lanthanum and neodymium chlorides were measured for the salt separation from electrorefiner uranium deposits in the temperature range of $825{\sim}910^{\circ}C$. The evaporation rate of both chlorides increased with an increasing templerature. The evaporation rate of lanthanum chloride varied from 0.12 to $1.68g/cm^2/h$. Neodymium chloride was more volatile than lanthanum chloride. The evaporation rate of neodymium chloride varied from 0.20 to $4.55g/cm^2/h$. The evaporation rate of both chlorides are more than $1g/cm^2/h$ at $900^{\circ}C$. Even though the evaporation rates of both chlorides were less than that of the process salt, the contents of the lanthanide chlorides were small in the adhered salt. Therefore it can be concluded that $900^{\circ}C$ is suitable for the operation temperature of the salt distiller.