• Journal of Environmental Science International
• /
• v.20 no.2
• /
• pp.251-260
• /
• 2011

$TiO_2$- and $SiO_2$-supported $Co_3O_4$, Pt and $Co_3O_4$-Pt catalysts have been studied for CO and $C_3H_8$ oxidations at temperatures less than $250^{\circ}C$ which is a lower limit of light-off temperatures to oxidize them during emission test cycles of gasoline-fueled automotives with TWCs (three-way catalytic converters) consisting mainly of Pt, Pd and Rh. All the catalysts after appropriate activation such as calcination at $350^{\circ}C$ and reduction at $400^{\circ}C$ exhibited significant dependence on both their preparation techniques and supports upon CO oxidation at chosen temperatures. A Pt/$TiO_2$ catalyst prepared by using an ion-exchange method (IE) has much better activity for such CO oxidation because of smaller Pt nanoparticles, compared to a supported Pt obtained via an incipient wetness (IW). Supported $Co_3O_4$-only catalysts are very active for CO oxidation even at $100^{\circ}C$, but the use of $TiO_2$ as a support and the IW technique give the best performances. These effects on supports and preparation methods were indicated for $Co_3O_4$-Pt catalysts. Based on activity profiles of CO oxidation at $100^{\circ}C$ over a physical mixture of supported Pt and $Co_3O_4$ after activation under different conditions, and typical light-off temperatures of CO and unburned hydrocarbons in common TWCs as tested for $C_3H_8$ oxidation at $250^{\circ}C$ with a Pt-exchanged $SiO_2$ catalyst, this study may offer an useful approach to substitute $Co_3O_4$ for a part of platinum group metals, particularly Pt, thereby lowering the usage of the precious metals.

• Applied Chemistry for Engineering
• /
• v.5 no.3
• /
• pp.425-430
• /
• 1994

The effect of inhibitors and catalysts in the synthesis of 2-hydroxyethyl methacrylate(2-HEMA) was studied. As catalysts, triethylamine(TEA), $FeCl_3{\cdot}6H_2O$, $Cu(NO_3)_2{\cdot}2H_2O$, $AlCl_3$, $Na_2Cr_2O_7$were selected. p-Methoxyphenol (PMP) of aq. $NaNO_3$ solution was used as an inhibitor in polymerization. in aq. $NaNO_3$ inhibitor system, triethylamine (TEA), $FeCl_3{\cdot}6H_2O$, and $Na_2Cr_2O_7$, showed good catalytic effects. When p-methoxyphenol(PMP) was used as a polymerization inhibitor, the reaction was very sluggish and noneffective because the metal ion such as $Fe^{3+}$ or $Cr^{6+}$ was reduced by PMP. On the contrary, when aq. $NaNO_3$ was used as an inhibitor in polymerization, the reaction was very fast without deactivation of the metal catalysts.

• Applied Chemistry for Engineering
• /
• v.23 no.5
• /
• pp.485-489
• /
• 2012

We investigated vanadium (V) loading effects on selective catalytic reduction (SCR) activity and $SO_2$ resistance using commercial SCR catalysts applied on a power plant and incinerator with different amounts of V loading. These catalysts were characterized using XRD, Raman, ICP, BET analysis and found to contain $TiO_2$ (anatase) supported $V_2O_5$ added $WO_3$ and $SiO_2$. The SCR activity of the catalysts increased by increasing either the $V_2O_5$ or the $WO_3$ loading amounts; the SCR activity of the catalysts added $WO_3$ is higher than that of $WO_3$-free catalysts. As the V loading amount in the catalyst increased, the $SO_2$ durability decreased. The $V_2O_5$ supported $TiO_2$ catalyst added $WO_3$ and $SiO_2$ inhibits the deactivation process by $SO_2$. The $SO_2$ resistance of catalysts added $SiO_2$ is higher than that of catalysts added $WO_3$.

• Clean Technology
• /
• v.20 no.1
• /
• pp.57-63
• /
• 2014

In this work, we performed the methanation with steam and synthesis gas of a low $H_2/CO$ ratio to develop a process for producing SNG (synthetic natural gas). In this experiment conditions, the water gas shift reaction and the methanation reaction take place at the same time, and insufficient supply of steam might cause the deactivation of the catalyst. Therefore, the reaction characteristics with the amount of steam was performed, and the methanation on syngas containing $CO_2$ of the high concentration were studied. As a result, the temperature in the catalyst bed decreased by the supply of steam, and the methanation and the water gas shift reaction occurred at the same time. Although methane yield slightly decreased at the methanation using syngas containing $CO_2$ of the high concentration, the long-term operation (1,000 h) in the experimental conditions of this study indicates that this condition is suitable for the new commercial scale SNG process.

• Journal of Microbiology and Biotechnology
• /
• v.29 no.3
• /
• pp.373-381
• /
• 2019

Site-directed mutagenesis was employed to generate five different triple point mutations in the double mutant (C295A/I86A) of Thermoanaerobacter ethanolicus alcohol dehydrogenase (TeSADH) by computer-aided modeling with the aim of widening the small alkyl-binding pocket. TeSADH engineering enables the enzyme to accept sterically hindered substrates that could not be accepted by the wild-type enzyme. The underline in the mutations highlights the additional point mutation on the double mutant TeSADH introduced in this work. The catalytic efficiency ($k_{cat}/K_M$) of the ${\underline{M151A}}$/C295A/I86A triple TeSADH mutant for acetophenone increased about 4.8-fold higher than that of the double mutant. A 2.4-fold increase in conversion of 3'-methylacetophenone to (R)-1-(3-methylphenyl)-ethanol with a yield of 87% was obtained by using ${\underline{V115A}}$/C295A/I86A mutant in asymmetric reduction. The ${\underline{A85G}}$/C295A/I86A mutant also produced (R)-1-(3-methylphenyl)-ethanol (1.7-fold) from 3'-methylacetophenone and (R)-1-(3-methoxyphenyl)-ethanol (1.2-fold) from 3'-methoxyacetophenone, with improved yield. In terms of thermal stability, the ${\underline{M151A}}$/C295A/I86A and ${\underline{V115A}}$/C295A/I86A mutants significantly increased ${\Delta}T_{1/2}$ by $+6.8^{\circ}C$ and $+2.4^{\circ}C$, respectively, with thermal deactivation constant ($k_d$) close to the wild-type enzyme. The ${\underline{M151A}}$/C295A/I86A mutant reacts optimally at $70^{\circ}C$ with almost 4 times more residual activity than the wild type. Considering broad substrate tolerance and thermal stability together, it would be promising to produce (R)-1-(3-methylphenyl)-ethanol from 3'-methylacetophenone by ${\underline{V115A}}$/C295A/I86A, and (R)-1-phenylethanol from acetophenone by ${\underline{M151A}}$/C295A/I86A mutant, in large-scale bioreduction processes.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.609-617
• /
• 2000

This study is aimed at investigating an effect of HCl gas on selective reduction of NOx over a CuHM and $V_2O_5-WO_3/TiO_2$ catalyst. SCR process is the most effective method to remove NOx, but catalyst can be deactivated by the acidic gas such as HCl gas which is also included in flue gas from the incinerator. In dry condition of flue gas, the CuHM catalyst treated by HCl gas has shown higher NO removal activity than the fresh catalyst. The activity of the catalyst can be restored by treating at $500^{\circ}C$. On the contrary. $V_2O_5-WO_3/TiO_2$ catalyst is obviously deactivated by HCl and the deactivation increases in proportion to the concentration of HCl gas. The deactivated catalyst is not restored to it's original activity by heat treatment for regeneration. In wet flue gas stream, the CuHM catalyst has shown lower activity than fresh catalyst and $V_2O_5-WO_3/TiO_2$ catalyst was severely deactivated by HCl treatment. The activity loss of catalysts are mainly due to the decrease of Br$\ddot{o}$nsted acid site on the catalyst surface by $NH_3$ TPD. The change of BET surface area of CuHM catalyst after the reaction isn't observed but $V_2O_5-WO_3/TiO_2$ catalyst is observed. The amount of $Cu^{{+}{+}}$ and $V_2O_5$ is decreased after the reaction. From these results, it is expected that CuHM catalyst should be better than $V_2O_5-WO_3/TiO_2$ catalyst for its application to the incineration of flue gas.

• Clean Technology
• /
• v.21 no.1
• /
• pp.68-75
• /
• 2015

In this study, we investigated the structure and properties of a highly heat conductive metal-ceramic core-shell CoAl₂O₄@Al micro-composite for heterogeneous catalysts support. The CoAl₂O₄@Al was prepared by hydrothermal surface oxidation of Al metal powder, which resulted in the structure with a high heat conductive Al metal core encapsulated by a high surface area CoAl₂O₄ shell. For comparison, CoAl₂O₄ was also prepared by co-precipitation method and also utilized for a catalyst support. Rh catalysts supported on CoAl₂O₄@Al and CoAl₂O₄ were prepared by incipient wetness impregnation and characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), CO chemisorption, and temperature-programmed reduction (TPR). The properties of catalysts were investigated for glycerol steam reforming reaction for hydrogen production at 550 ℃. Rh/CoAl₂O₄@Al exhibited about 2.8 times higher glycerol conversion turnover frequency (TOF) than Rh/CoAl₂O₄ due to facilitated heat transport through the core-shell structure. The CoAl₂O₄@Al and CoAl₂O₄ also showed some catalytic activities due to a partial reduction of Co on the support, and a higher catalytic activity was also found on the CoAl₂O₄@Al core-shell than CoAl₂O₄. These catalysts, however, displayed deactivation on the reaction stream due to carbon deposition on the catalysts surface.

• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.808-818
• /
• 1994

Effects of ceria additive on the activity and thermal aging behavior of supported Ru catalysts were investigated using Ru/${\gamma}$-$Al_2O_3$and Ru/$CeO_2$-${\gamma}$-$Al_2O_3$. The catalysts were characterized by $^{129}Xe$-NMR and $H_2$ chemisorption. The cataltic activity for conversion of CO, HC and $NO_x$ was measured using simulated automobile engine exhausts under lean, rich and stoichiometric conditions. For both fresh and aged catalysts, Ru/$CeO_2$-${\gamma}$-$Al_2O_3$ was more active than Ru/${\gamma}$-$Al_2O_3$ for all three pollutants. Results of $^{129}Xe$-NMR and $H_2$ chemisorption indicated that sintering of Ru particles occurred to the same extent for both catalysts during the thermal aging process. After thermal aging at 673K, however, the catalytic activity of the aged Ru/$CeO_2$-${\gamma}$-$Al_2O_3$ was substantially higher than that of the fresh one, while the activity of Ru/${\gamma}$-$Al_2O_3$ decreased after the thermal aging. This finding may suggest new active sites were created during the thermal aging, probably in the vicinity of the interface between Ru and Ce. For more quantitative investigation of the effect of a cation such as Ce on the thermal aging of Ru metal particles, Ru catalysts supported on cation-exchanged Y-zeolites were used as the model catalysts. The results indicated that when Ba, Ca, La, Y or Ce was used for the cation exchange, the exchanged cation did not affect the thermal aging behavior of Ru in Y-zeolite, as evidenced by $^{129}Xe$-NMR and EXAFS.

• Clean Technology
• /
• v.22 no.1
• /
• pp.53-61
• /
• 2016

Steam reforming of tar produced from biomass gasification was conducted using several Ni-based catalysts. In labscale, the catalytic steam reforming of toluene which is a major component of biomass tar was studied. A fixed bed reactor was used at various temperatures of 400-800 ℃. Ru (0.6 wt%) and Mn or K (1 wt%) were applied as a promoter in Ni based catalysts. Generally, Ni/Ru-K/Al₂O₃ catalyst shows higher performance on steam reforming of toluene than Ni/Ru-Mn/Al₂O₃ catalyst. Used catalysts were analyzed by XRD and TGA to detect sintering and carbon deposition. Base on the lab-scale studies, the monolith and pellet type catalysts were tested in 1 ton/day scale biomass gasification system. Ni/Ru-K/Al₂O₃ monolith catalyst shows high tar reforming performance at high temperature. In addition, Ni/Ru-Mn/Al₂O₃ monolith catalyst was showed deactivation with operation time. Reforming performance of Ni/Ru-K/Al₂O₃ pellet catalyst which showed 66.7% tar conversion at 587 ℃ was compared to regenerated one. Overall, Ni/Ru-K/Al₂O₃ pellet catalyst shows higher stability and performance than other used catalysts.

• Clean Technology
• /
• v.25 no.1
• /
• pp.91-97
• /
• 2019

Oxidative desulfurization (ODS) has received much attention in recent years because refractory sulfur compounds such as dibenzothiophenes can be oxidized selectively to their corresponding sulfoxides and sulfones, and these products can be removed by extraction and adsorption. In this work, The oxidative desulfurization of marine diesel fuel was performed in a batch reactor with hydrogen peroxide ($H_2O_2$) in the presence of various supported heteropoly acid catalysts. The catalysts were characterized by XRD, XRF, XPS and nitrogen adsorption isotherm techniques. Based on the sulfur removal efficiency of promising silica supported heteropoly acid catalysts, the ranking of catalytic activity was: $30\;H_3PW_{12}/SiO_2$ > $30\;H_3PMo_{12}/SiO_2$ > $30\;H_4SiW_{12}/SiO_2$, which appears to be related with their intrinsic acid strength. The $30\;H_3PW_{12}/SiO_2$ catalyst showed the highest initial sulfur removal efficiency of about 66% under reaction conditions of $30^{\circ}C$, $0.025g\;mL^{-1}$ (cat./oil), 1 h reaction time. However, through the recycle test of the $H_3PW_{12}/SiO_2$ catalyst, significant deactivation was observed, which was attributed to the elution of the active component $H_3PW_{12}$. By introducing cesium cation ($Cs^+$) into the $H_3PW_{12}/SiO_2$ catalyst, the stability of the catalyst was improved with changing the solubility, and the $Cs^+$ ion exchanged catalyst could be recycled for at least five times without severe elution.