• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.1-8
• /
• 2002

For gasoline engines, a three-way catalytic converter that has the maximum efficiency at stoichiometric air/fuel ratio is used to clean up the exhaust gas. So a precise air/fuel ratio control is necessary to maximize the catalytic conversion efficiency, For a transient condition, a fred-forward air/fuel ratio control method that estimates the air mass inducted into a cylinder is being used. In this study, a fuel injection map that makes an accurate air/fuel ratio control possible was constructed for the very same transient condition. For the same condition above, intake air model and fuel model were refined so that fuel injection values based on air mass through a throttle valve and intake manifold pressure are equal to the map values.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.516-521
• /
• 2004

In this paper, the effects of ethanol blended gasoline on emissions and their catalytic conversion efficiencies characteristics were investigated in gasoline engine with an electronic fuel injection. The results showed that the increase of ethanol concentration in the blended fuels brought the reduction of THC and $CO_2$ emissions from the gasoline engine. THC emissions were drastically reduced up to thirty percent. And brake specific fuel consumption was increased. but brake specific energy consumption was similar level. However. unburned ethanol and acetaldehyde emissions increased. The conversion efficiency of Pt/Rh based three-way catalysts and the effect of ethanol on CO and NOx emissions were investigated by the change of engine speed. load and air/fuel ratio. Furthermore, the ethanol blended fuel results in the reduction effect of THC. CO and NOx emissions at idle speed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.67-74
• /
• 2001

A synchronized secondaty air injection method has been developed to hydrocarbon emission by injecting secondary air intermittently into exhaust port. The method has been tested in a single cylinder spark-ignition engine operating at cold-steady / cold-start conditions. Effects of air injection timing, intake pressure and engine air-fuel ratio have been investigated at cold-steady condition. Also, hydrocarbon emission and exhaust gas temperature with catalytic conberter are compared with a continuous SAI method and base condition at cold-start condition. Resules show that hydrocarbon reduction rate and exhaust gas temperature are sensitive to the timing of synchronized SAI. At cold-steady condition, HC emission is minimum at engine air-fuel ratio of 10. At cold-start condition, the accumulated hydrocarbon emission during the first 120 s decreases about 56% and 22% with the synchronized and continuous SAI, respectively, compared to that of base condition.

• Journal of the korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.46-53
• /
• 1981

This paper describes emission control of hydrocarbon and carbon-monoxide due to oxidizing catalyst. The experiment was performed on a precious metal pelleted catalyst(Pt). The factors of the efficiency for purification due to oxidizing catalyst are space velocity, temperature, composition of exhaust gas and supplementary air. The experiment was carried out to control the factors of efficiency for purification. The results of experimental study show that temperature of catalytic converter, supplementary air and space velocity affected the efficiency for purification of hydrocarbon and carbon monoxide.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2003.11a
• /
• pp.167-168
• /
• 2003

우리나라는 1987년 7월부터 휘발유 및 LPG 연료 사용 자동차에 배출가스 저감장치인 삼원촉매(3way catalytic converter)를 부착하였고 배출가스 측정방법도 중량규제(ｇ/km)로 하였다. 그러나 이륜자동차는 2001년부터 2행정기관에 대해서 산화촉매를 부착토록 하였으며, 오염물질 측정방법도 2000년에 이르러 정지가동시 측정하는 농도규제(%)에서 트랜지언트(transient)방법에 의한 중량규제(ｇ/km)로 강화하였다. (중략)

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.66-76
• /
• 1987

The control technique for an electronic engine is studied. For this study an IBM-PC and a throttle body fuel injection system are selected. The computer controls fuel injection, spark timing, exhaust gas recirculation and idle speed. Fuel injection is adjusted either by a feed back signal of a zirconia $O_{2}$ sensor or programmed logic for starting, deceleration, warm ing up and idle modes. When a 3-way catalytic converter is used with the electronic engine control system, CO, THC, and NOx were reduced more than 90% simultaneously.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.1-8
• /
• 2005

In this study, $TiO_2$ powders were prepared by hydro-thermal synthesis with titanium tetra isopropoxide. The prepared $TiO_2$ and the commercial $TiO_2$(P-25, Degussa) were by impregnating $H_2PtCl_6$ solution or the leached solution from the waste catalytic converter of automobile. Modified photocatalysts were analyzed by ICP-AES, UV-DRS, XRD, SEM. And band-gap energy of modified photo-catalyst was found to decreased to 1.76eV and basic structure was changed upon modification by leached solution. Modified photocatalysts were coated on the wallpaper after using mixed solution with adhesive materials(PVC). And then to know the modified photo catalysts tested the reactivity and quantum efficiency in the mixed gas with NO as reactants in the photo catalytic reactor. In the gas phase, photo-catalytic activity of NO was the highest for modified P-25 catalysts(P-25(w)) that P-25(w) was impregnated by leached solution of wasted catalytic converter.

• Journal of the Korean Institute of Gas
• /
• v.3 no.2 s.7
• /
• pp.70-76
• /
• 1999

Because of the tight pollution control of $SO_2$ emission, sulfuric acid manufacturers have been interested in the operation with the highest possible conversion efficiency. In this work, the design criteria and operating conditions of the catalytic converter were investigated for maximum conversion efficiency and minimum $SO_2$ emission by parametric analysis and process optimization for the existing acid plants. The Double Converter/Double Absorber(DC/DA) process was investigated by varying $SO_2$ compositions of feed gas, pressures and temperatures of layers of the converter and the depth of the catalyst beds. In order to evaluate the process, a computer simulator for sulfuric acid plants has been developed. The results by process optimization could be used for the converter design and operating conditions with highest conversion efficiency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3125-3134
• /
• 2010

Three-way catalyst durability in the Korea requires 5 years/80,000km in 1988 but require 10 years/120,000km after 2002. Domestic three-way catalyst satisfies exhaust gas conversion efficiency or pressure drop etc. but don't satisfy thermal durability. Three-way catalyst maintains high temperature in interior domain but maintain low temperature on outside surface. This study evaluated thermal durability of three-way catalyst by thermal flow and structure analysis and the procedure is as followings. Thermal flow parameters ranges were determined by vehicle test and basic thermal flow analysis. Response surface for rear catalyst temperature was constructed using the design of experiment (DOE) for thermal flow parameters. Thermal flow parameters for rear catalyst temperature in vehicles examination were predicted by desirability function. Temperature distribution of three-way catalyst was estimated by thermal flow analysis for predicted thermal flow parameters.

• International Journal of Automotive Technology
• /
• v.6 no.5
• /
• pp.445-451
• /
• 2005

Most of the pollutants from passenger cars are emitted during the cold-transient phase of the FTP-75 test. In order to reduce the exhaust emissions during the cold-transient period, it is essential to warm up the catalyst as fast as possible after the engine starts, and the Unburned Exhaust Gas Ignition (UEGI) technology was developed through our previous studies to help close-coupled catalytic converters (CCC) reach the light-off temperature within a few seconds after cold-start. The UEGI system operates by igniting the unburned exhaust mixture by glow plugs installed upstream of the catalyst. The flame generates a high amount of heat, and if the heat is concentrated on a specific area of monolith surface, then thermal crack or failure of the monolith could occur. Therefore, it is very important to monitor the temperature distribution in the CCC during the UEGI operation, so the local temperatures in the monolith were measured using thermocouples. Experimental results showed that the temperature of CCC rises faster with the UEGI technology, and the CCC reaches the light-off temperature earlier than the baseline case. Under the conditions tested, the light-off time of the baseline case was 62 seconds, compared with 33 seconds for the UEGI case. The peak temperature is well under the thermal melting condition, and temperature distribution is not so severe as to consider thermal stress. It is noted that the UEGI technology is an effective method to warm up the catalyst with a small amount of thermal stress during the cold start period.