• Journal of the Korean Chemical Society
• /
• v.22 no.6
• /
• pp.370-379
• /
• 1978

The specific rate constants for the oxidation reactions of carbon monoxide on a unit catalytic surface area were measured. The catalysts used were NiO made from $Ni(NO_3)_2,\;and\;Ni(OH)_2$, and Mn$O_2$ made from Mn$(NO_3)_2$. At low pressure the reaction rate was found to be of second order and the activation energies were 12 kcal/mole (on NiO made from Ni$(NO_3)_2$, 17 kcal/mole (on NiO made from Ni$(OH)_2)$) and 18 kcal/mole (on Mn$O_2$). Plausible reaction mechanisms were proposed from the experimentally determined reaction orders.

• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.333-336
• /
• 2010

Fe/$Al_2O_3$ granules with various compositions were prepared by combining sol-gel with oil drop method for Fishcer-Tropsh reaction to produce light olefin from synthesis gas. The granules was characterized and employed as a catalyst in the reaction. The surface area of granules was decreased with increasing Fe concentration. Especially, granule with 1.5 of Al/Fe ratios showed the highest CO conversion. However, the olefin selectivity was hardly affected by Al/Fe ratio. K concentration of granule gave a significant effect on catalytic performance. Initial CO conversion and olefin selectivity were increased with K concentration. However, the catalyst with higher K concentration was deactivated rapidly.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.2
• /
• pp.96-101
• /
• 2021

Developing effective and earth-abundant electrocatalyst for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is critical for the commercialization of a water splitting system. In particular, the overpotential of the OER is relatively higher than the HER, and thus, it is considered that one of the important methods to enhance the performance of the electrocatalyst is to reduce the overpotential of the OER. We report effects of incorporation of metalloid into Ni(OH)2 microcrystal on electrocatalytic activities. In this study, Te incorporated Ni(OH)2 (��Te-Ni(OH)2) were grown on three-dimensional porous NF by a facile solvothermal method with �� = 1, 3 and 5. Homogeneous microplate structure on the NF was clearly observed for the Ni(OH)2/NF and ��Te-Ni(OH)2/NF samples. However, irregular and collapsed nanostructures were found on the surface of nickel foam when Te precursor ratio is (��) over 3. Electrocatalytic OER properties were analysed by Linear sweep voltammetry (LSV) and Electrochemical impedance spectroscopy (EIS). The amount of Te incorporation used in the electrocatalytic reaction was found to play a crucial role in improving catalytic activity. The optimum Te amount (��) introduced into the Ni(OH)2/NF was discussed with respect to their OER performance.

• Applied Chemistry for Engineering
• /
• v.31 no.1
• /
• pp.108-114
• /
• 2020

In this study, NH₃-selective catalytic oxidation (SCO) efficiencies according to calcination/reduction conditions were compared when preparing various Ru[1]/TiO₂ catalysts. The Ru[1]/TiO₂ red catalyst had better NH₃ conversion and NH₃ to N₂ conversion than those of Ru[1]/TiO₂ cal. Physico-chemical properties of Ru[1]/TiO₂ catalysts were confirmed by Brunauer Emmett Teller (BET), X-ray diffraction (XRD), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) and temperature programmed reduction (H₂-TPR) analyses, and the properties were shown to affect the dispersion and surface adsorption oxygen species (O_β) ratio of the active metal.

• Clean Technology
• /
• v.19 no.1
• /
• pp.13-21
• /
• 2013

The hydrogenolysis of cellulose into polyols was examined over Pt/$Cs_xH_{3-x}PW_{12}O_{40}$ catalysts containing different Cs fractions. The surface area and Pt dispersion of Pt/$Cs_xH_{3-x}PW_{12}O_{40}$ catalysts were found to increase with Cs content. Similar polyol yields were obtained over Pt/$Cs_xH_{3-x}PW_{12}O_{40}$ catalysts irrespective of their Cs content. The catalytic activity of Pt/$Cs_xH_{3-x}PW_{12}O_{40}$ was comparable to that of Ni/W/SBA-15 and combined catalytic systems such as Pt/AC+$H_3PW_{12}O_{40}$ and Pt/AC + $Cs_{3.0}PW_{12}O_{40}$. Some polyanion species were found to leach from the Pt/$Cs_xH_{3-x}PW_{12}O_{40}$ catalyst during the course of the reaction.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.4
• /
• pp.259-269
• /
• 2002

A battery based on the lithium/elemental sulfur redox couple has the advantage of high theoretical specific capacity of 1,675 mAh/g-sulfur. However, Li/S battery has bad cyclic durability at room temperature due to sulfur active material loss resulting from lithium polysulfide dissolution. To improve the cycle life of Li/S battery, PEGDME (Poly(ethylene glycol) dimethyl ether) 500 containing 1M LiTFSI salt which has high viscosity was used as electrolyte to retard the polysulfide dissolution and nano-sized $Mg_{0.6}Ni_{0.4}O$ was added to sulfur cathode as additive to adsorb soluble polysulfide within sulfur cathode. From experimental results, the improvement of the capacity and cycle life of Li/S battery was observed( maximum discharge capacity : 1,185 mAh/g-sulfur, C50/C1 = 85 % ). Through the charge-discharge test, we knew that PEGDME 500 played a role of preventing incomplete charge-discharge $behavior^{1,2)$. And then, in sulfur dissolution analysis and rate capability test, we first confirmed that nano-sized $Mg_{0.6}Ni_{0.4}O$ had polysulfide adsorbing effect and catalytic effect of promoting the Li/S redox reaction. In addition, from BET surface area analysis, we also verified that it played the part of increasing the porosity of sulfur cathode.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.1
• /
• pp.89-96
• /
• 2004

The effect of La promoter on the carbon deposition and catalytic activity in the synthesis gas production with supported Ni catalysts was investigated. Active component was Ni and support was $CeO_2$ and the promoter used was La. The reaction was carried out in a fixed bed reactor at 1 atm and $650{\sim}800^{\circ}C$. The catalysts were prepared by two methods, the impregnation method and urea method. The catalysts prepared by the urea method showed 10 times higher surface area than those of prepared by the impregnation method. By the introduction of La promoter in the catalyst system, carbon deposition was remarkably reduced from 16% to 2%. It appears that the promoter facilitates the formation of a stable fluoride-type phase, which reduces the carbon deposition. The best catalytic activity and CO and $H_2$ selectivities were obtained with 2.5wt% $Ni/Ce(La)O_x$ catalyst at $750^{\circ}C$, giving 90% methane conversion, 93 and.80% of CO and $H_2$ selectivities, respectively.

• Applied Chemistry for Engineering
• /
• v.5 no.6
• /
• pp.925-934
• /
• 1994

Nickel recovered from the spent oil-hydrogenation catalysts was used in hydrogenation catalyst preparation. The spent catalyst contains approximately 21.8% Ni, 0.7% Mg, and small quantities of Al, Fe, and Zn. Nickel recovery was obtained by inorganic acid digestion in the order of HCI>$NHO_3$>$H_2SO_4$. For $HNO_3$, 3hour extraction with 3N solution was satisfactory. In the PH range of 6.5~9.0, Ni recovery was higher, but metallic impurities were found to be coprecipitated. The PH in the range of 7.0~9.0 seems to be the optimum condition for separation to obtain acceptable Ni precipitates without the decrease of purity. The catalysts prepared with reclaimed nickel by wet reduction methods showed catalytic activities close to those prepared using reagent nickel in the oil hydrogenation reaction. The surface areas of the support do not seem to affect the catalytic activity.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.10
• /
• pp.3712-3719
• /
• 2011

Confined Pt and $CoFe_2O_4$ nanoparticles (NPs) in a mesoporous core/shell silica microsphere, Pt-$CoFe_2O_4$@meso-$SiO_2$, were prepared using a bi-functional linker molecule. A large number of Pt NPs in Pt-$CoFe_2O_4$@meso-$SiO_2$, ranging from 5 to 8 nm, are embedded into the shell and some of them are in close contact with $CoFe_2O_4$ NPs. The hydrogenation of cyclohexene over the Pt-$CoFe_2O_4$@meso-$SiO_2$ microsphere at $25^{\circ}C$ and 1 atm of $H_2$ yields cyclohexane as a major product. In addition, it gives oxygenated products. Control experiments with $^{18}O$-labelled water and acetone suggest that surface-bound oxygen atoms in $CoFe_2O_4$ are associated with the formation of the oxygenated products. This oxidation reaction is operative only if $CoFe_2O_4$ and Pt NPs are in close contact. The Pt-$CoFe_2O_4$@meso-$SiO_2$ catalyst is separated simply by a magnet, which can be re-used without affecting the catalytic efficiency.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.77.2-77.2
• /
• 2013

In this talk, I will briefly review recent results of my group related to application of atomic layer deposition (ALD) for fabricating environmental catalysts and organic solar cells. ALD was used for preparing thin films of TiO2 and NiO on mesporous silica with a mean pore size of 15 nm. Upon depositing TiO2 thin films of TiO2 using ALD, the mesoporous structure of the silica substrate was preserved to some extent. We show that efficiency for removing toluene by adsorption and catalytic oxidation is dependent of mean thickness of TiO2 deposited on silica, i.e., fine tuning of the thickness of thin film using ALD can be beneficial for preparing high-performing adsorbents and oxidation catalysts of volatile organic compound. NiO/silica system prepared by ALD was used for catalysts of chemical conversion of CO2. Here, NiO nanoparticles are well dispersed on silica and confiend in the pore, showing high catalytic activity and stability at 800oC for CO2 reforming of methane reaction. We also used ALD for surface modulation of buffer layers of organic solar cell. TiO2 and ZnO thin films were deposited on wet-chemically prepared ZnO ripple structures, and thin films with mean thickness of ~2 nm showed highest power conversion efficiency of organic solar cell. Moreover, performance of ALD-prepared organic solar cells were shown to be more stable than those without ALD. Thin films of oxides deposited on ZnO ripple buffer layer could heal defect sites of ZnO, which can act as recombination center of electrons and holes.