• 한국주조공학회지
• /
• 제31권1호
• /
• pp.11-17
• /
• 2011

The effect of CaO addition to AM60B Mg alloy on tensile properties has been investigated, with focus on strength and ductility at room and elevated temperatures. The 0.25-0.65wt% CaO added AM60B Eco-Mg diecastings were prepared by high pressure die casting using Buhler 1,450-ton cold chamber machine without $SF_6$ and $SO_2$ gases. The microstructures and tensile properties of each alloy were tested. The results show that the grains of AM60B are refined and the mechanical properties increase with CaO addition at room temperature. The improvement of strength and ductility is prominent at 0.45-0.55wt% CaO addition. Also, improved mechanical properties are maintained at elevated temperature of $150^{\circ}C$. CaO addition results in $Al_2Ca$ phase formation mostly on the grain boundaries. This phase leads to the refinement of grain structures and improvement of ductility as well as strength. The suppression of ${\beta}-Mg_{17}Al_{12}$ phase as well as the decrease of fracture surface porosity and other casting defects caused by melt cleanliness also contribute to the enhancement of mechanical properties of AM60B Eco-Mg at room and elevated temperature.

• KEPCO Journal on Electric Power and Energy
• /
• 제7권1호
• /
• pp.129-135
• /
• 2021

Recently, additive manufacturing (AM) technology such as powder bed fusion (PBF) and directed energy deposition (DED) are actively attempted as consumers' needs for parts with complex shapes and expensive materials. In the present work, the effect of processing parameters on the mechanical properties of 316L stainless steel coupons fabricated by PBF and DED AM technology was investigated. Three major mechanical tests, including tension, impact, and fatigue, were performed on coupons extracted from the standard components at angles of 0, 45, 90 degrees for the build layers, and compared with those of investment casting and commercial wrought products. Austenitic 316L stainless steel additively manufactured have been well known to be generally stronger but highly vulnerable to impact and lack in elongation compared to casting and wrought materials. The process-induced pore density has been proved the most critical factor in determining the mechanical properties of AM-built metal parts. Therefore, it was strongly recommended to reduce those lack of fusion defects as much as possible by carefully control the energy density of the laser. For example, under the high energy density conditions, PBF-built parts showed 46% higher tensile strength but more than 75% lower impact strength than the wrought products. However, by optimizing the energy density of the laser of the metal AM system, it has been confirmed that it is possible to manufacture metal parts that can satisfy both strength and ductility, and thus it is expected to be actively applied in the field of electric power section soon.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제21권3호
• /
• pp.257-265
• /
• 1999

골재생유도술에 의한 골재생과정의 생물학적 현상을 보다 구체적으로 이해하고자, 백서의 대퇴골에 인위적인 골결손부를 형성하고 비흡수성 차폐막을 설치한 다음 골재생유도 과정에서의 미세혈관의 구축 양상을 통상적인 광학 현미경적 소견 및 미세혈관주형 표본 관찰법을 중심으로 관찰한바 다음과 같은 결과를 얻었다. 광학 현미경적 소견의 초기 즉 술후 1주 및 2주 소견상 차폐막에 의해 피개된 실험부에서 보다 정연한 골성회복이 이루어졌으며, 이는 차폐막으로 인한 혈관망 형성의 양상에 의해 영향을 받는 것으로 나타났다. 즉, 차폐막에 의한 연조직 침입이 차단됨으로 인해 인접 골조직으로부터 수평적으로 들어온 혈관에 의해 규칙적인 혈관 분포를 나타내나, 대조군의 경우 연조직에서 유입된 혈관망에 의해 불규칙한 혈관망을 나타내었다. 시간이 경과되면서 재생된 결손부의 골은 재구성되면서 대조군과 실험군 사이에 골성회복의 양상은 유사하였으나, 인접 실험군의 골조직으로부터 유입된 혈관에 의해 형성된 규칙적인 혈관망이 연조직으로부터 침입한 혈관에 의해 그 규칙적인 배열이 흐트러진 대조군에 비하여 골성회복의 속도가 빨라진다는 사실을 확인하였다. 이상의 결과는 차폐막에 의한 골재생 유도과정에서 혈관의 유래와 혈관망의 정렬상태가 골성회복의 속도와 밀접한 관련이 있음을 보여주는 것이다.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.482-489
• /
• 2020

본 연구의 목적은 소비자 및 현장의 니즈에 부합하면서 다이캐스팅으로 생산할 수 있는 커플링 부품을 개발하고자 하였으며, 유동 및 응고해석을 기반으로 다이캐스팅 금형 설계, 제작, 및 사출조건 최적화 도출을 실시하였고 사출된 제품의 측정 및 평가를 수행하였다. 유동해석을 통하여 캐비티 내부가 100 % 충진되기 위한 적정한 사출조건은 용탕의 온도 670 ℃, 사출속도 1.164 m/s, 충진압력 6.324~18.77 MPa로 분석되었다. 또한, 응고율이 69.47 %일 때 4개의 캐비티 모두에서 100 %에 근접하는 응고가 발생됨을 알 수 있었으며, 이를 기초로 시사출 조건설정 등에 응용하였으며 그 결과 사이클 타임은 약 6.5초로 도출되었다. 다이캐스팅으로 시사출된 제품의 표면 및 내부의 품질 검사를 수행한 결과 성형불량 및 기공 등의 결함은 전혀 발견되지 않았으며, 주요 개소의 치수를 측정한 결과 모든 항목에서 허용하는 공차 이내의 값을 보였다. 또한, 게이트로부터 약 45 mm 이격된 곳의 평균 경도값은 97.7(Hv)로 나타나는 등 전체적으로 양호한 치수 및 품질의 부품을 제작할 수 있었다.

• 한국주조공학회지
• /
• 제12권4호
• /
• pp.305-316
• /
• 1992

Steel and iron castings made with expandable polystylene (referred to hereafter as EPS) patterns are often affected by distinctive defects associated with incomplete decomposition of the EPS as the molds are filled with metal. The effects of practical factors on carbon pick-up were investigated on the specimens, by taking successive layers of swarf and analysis, whereas the lustrous carbon is determined by using combustion analysis. The quality of the castings, with particular reference to carbon pick-up in low carbon steel and lustrous carbon on gray iron, is further influenced to a significant extent by such practical factors as reduced pressure, the pouring temperature, the density of EPS pattern, the additive in coating and in pattern and the casting thickness. The rate at which carbon pick-up and lustrous carbon deposites are formed can be reduced by reducing the density of the pattern and also reducing pressure, especially by adding $Na_2CO_3$ in coating and in pattern to promote $CO_2$ evolution. The upper parts of castings obtained using EPS patterns are slightly higher in carbon pick-up and in lustrous carbon than other parts.

• 한국재료학회지
• /
• 제28권10호
• /
• pp.544-550
• /
• 2018

The passivation of AZ91D Mg alloys by plasma anodization requires deliberate choice of process parameters due to the presence of large amounts of structural defects. We study the dependence of pore formation, surface roughness and corrosion resistance on voltage by comparing the direct current (DC) mode and the pulse wave (pulse) mode in which anodization is performed. In the DC plasma anodization mode, the thickness of the electrolytic oxide film of the AZ91D alloy is uneven. In the pulse mode, the thickness is relatively uniform and the formed thin film has a three-layer structure. The pulse mode creates less roughness, uniform thickness and improved corrosion resistance. Thus, the change of power mode from DC to pulse at 150 V decreases the surface roughness (Ra) from $0.9{\mu}m$ to $0.1{\mu}m$ and increases the corrosion resistance in rating number (RN) from 5 to 9.5. Our study shows that an optimal oxide film can be obtained with a pulse voltage of 150 V, which produces an excellent coating on the AZ91D casting alloy.

• Journal of Welding and Joining
• /
• 제8권4호
• /
• pp.35-45
• /
• 1990

Casting are widely used nodays as complicated and diversified forming materials due to its superior castability. However the welding of cast iron has not been accompaniced satisfactory resulting in an microstructure change happened in the heat affected zone (HAZ), especially the graphite are formed and shaped consecutively in the area and it has great impact on the crack occuring and growth together with martensite forming in this area. It case of gray cast iron welding, it is required for pre-heat treatment or specific welding consumables to restrain forming the martensite in the HAZ. In this study, by applying the plasma surface overlaid welding. Fe-Mn-Al steel powder has been used for improvement of anti-crackability in the HAZ and much attention has been paid to establish the overlaid welding method for gray cast iron so that optimum welding conditions may prevent the cracking. With our experiments, we have found that to prevent defects which may occur in the HAZ, the overlaid welding technique for gray cast iron has been developed.

• 소성∙가공
• /
• 제15권6호
• /
• pp.421-427
• /
• 2006

Drawing process of Al-1%Si bonding wire considering fine Si particle is analyzed in this study using FE-simulation. Al-1%Si boding wire requires electric conductivity because Al-1%Si bonding wire is used for interconnection in semiconductor device. About 1% of Si is added to Al wire for dispersion-strengthening. Distribution and shape of fine Si particle have strongly influence on the wire drawing process. In this study, therefore, the finite-element model based on the observation of wire by continuous casting is used to analyze the effect of various parameters, such as the reduction in area, the semi-die angle, the aspect ratio, the inter-particle spacing and orientation angle of the fine Si particle on wire drawing processes. The effect of each parameter on the wire drawing process is investigated from the aspect of ductility and defects of wire. From the results of the analysis, it is possible to obtain the important basic data which can be guaranteed in the fracture prevention of Al-1 %Si wire.

• 한국세라믹학회지
• /
• 제47권6호
• /
• pp.566-571
• /
• 2010

Dispersion behavior of the slurries consisted of bimodal-type AlN powders was examined in non-aqueous solvent system. Azotropic solvent system and copolymer acidic dispersant were applied to the slurries. Measurements of the sedimentation height and the viscosity of the each slurry, and the test of particle size distribution of the each powder sample were conducted as examinations for the dispersion behavior at the various dispersant contents. The bimodal-type particle size distribution was continued after addition of the dispersant and small particle portions were increased as the dispersant content increases. The density of the green sheet was also increased as the dispersant content increases and a green density of $2.114\;g/cm^3$ was obtained at the sample prepared from 2.4 wt% dispersant content. The increase of large particle portions resulted in the surface defects of the green sheets.

• 한국주조공학회지
• /
• 제13권3호
• /
• pp.248-258
• /
• 1993

A semi-solid alloy in which solid and liquid phase are co-existing is obtained by stirring of A17075 molten metal. A semi-solid alloy is dependent on the corresponding temperature within the solid-liquid range, and the process parameters should be controlled accurately to obtain the homogeneous semisolid alloy. The fabrication possibility of fiber-reinforced aluminum alloy containing $Al_2O_3$ short fibers with vigorous agitation of short fibers were obtained by control of stirring time, solid fraction and impeller speed in extrusion billet fabrication processes. The microstructure to extrusion billet fabricated by low pressure casting was investigated for fiber dispersion state. The relationship between the extrustion force and velocity at hot extrustion, the flow strain and extrusion ratio were theoretically described. The surface defects with lubricants and without lubricant after hot extrusion were investigated. The composites materials after hot extrusion were measured by vickers hardness with extrusion ratio. It has become clear that the secondary working such as hot extrusion was very useful to obtained improved the mechanical properties of metal matrix composites.