• 소성∙가공
• /
• 제16권2호
• /
• pp.126-131
• /
• 2007

Voids in a large rotor are formed in solidification process of a cast ingot. The voids have to be eliminated from the rotor by a forming process, because they would became stress-intensity factors which suddenly fracture the rotor in the operation. Previous studies on void-elimination of a large rotor have mainly focused on finding the process variables affecting the void-closure. But the study on the amount of void closure in a large rotor has been very rare. This study was performed to obtain an equation which predicts the amount of void-closure in a forging process of a large rotor and to evaluate the availability of the void-closure equation through finite element analyses. Firstly, 2D FE analysis was carried out to find effects of time integral of hydrostatic stress and effective strain on void volume rate of a large rotor in the upsetting process for various diameters and shapes of void, and material temperature. From the 2D FE analysis, we found that effective strain was suitable for predicting the void-closure of a large rotor, because there was a constant relationship between void volume rate and effective strain. And a void-closure equation was proposed fur predicting void-closure of a large rotor in the upsetting process. Finally, ken the 3D FE analysis, the proposed void-closure equation was verified to be useful for upsetting and cogging processes.

• 소성∙가공
• /
• 제19권6호
• /
• pp.378-386
• /
• 2010

Nowadays there has been great interest in using heat treated cast material for press dies due to several advantages like reduction in die production costs. However, in hot press forming processes H13 forged tool steel is mostly used. Cooling performance of dies in hot press forming processes is considered as an important factor of study and also the IHTC parameter between cast material die and sheet metal should be considered as an essential. In the present study, the IHTC was calculated for the sheet metal in the hot press forming process with cast and forged material dies. The temperature measurements were performed for the sheet metal, casting and forged material dies by applying various contact pressure in hot press forming. IHTC was calculated and studied by adopting the inverse heat convection method in DEFORM-2D. Each IHTC was considered as a function of contact time and contact pressure. The experimental data were compared with calculated data obtained from the proposed equation and references.

• 보존과학연구
• /
• 통권23호
• /
• pp.131-147
• /
• 2002

Kkonmoe relic located in Jangan-gu, Suwon-si, Gyeonggi-do Provinceis an example of the wide chronology from the Three Kingdoms Period to Joseon Dynasty. Examinations on a forged iron ax, a cast iron ax and an iron sickle excavated from this relic revealed the microstructure structure of the metal and the manufacturing technologies. Microstructure investigation was carried out with a metallurgical microscope and a Vickers hardness tester was used to measure the hardness of the micro structures. The test results show that the forged iron ax has a ferrite and pearlitestructure. It is made of low carbon steel and then carbonized to increase carbon content. After carbonization, the surface grains are reworked and the surface decarbonized. In case of the iron sickle, it is forged from low carbon steel, then carbonized and hardened, to increase overall strength. The sickle blade is carbonized and quenched after forging, resulting in afirm, solid blade. Heat treatment to remove brittleness is not applied to the cast ironartifact, which is manufactured by solidifing hypo-eutectic cast iron with a3-4% carbon content and white cast iron. All artifacts are produced from steel and subjected to a carbonization process. To increase hardness of the blade, additional heat treatment is applied.

• 보존과학회지
• /
• 제29권4호
• /
• pp.367-378
• /
• 2013

원삼국시대에 속하는 경기도 김포시 양촌유적에서 출토된 단조철부 5점과 주조철부 1점을 대상으로 미세조직 관찰과 비금속개재물 분석을 실시하였다. 단조품에 사용된 소재는 순철에 가까운 소재와 저탄소강이 사용되었고 성형 후 1점에만 담금질을 하였다. 주조품은 주철을 탈탄시킨 미세조직이 보여 주철탈탄 제강법이 적용된 것을 확인하였다. 비금속개재물 분석결과 철부는 고체저온환원법으로 제련하여 생산된 괴련철을 두드려서 제작하였다. FeO 함량이 $SiO_2$에 비해 비교적 높게 나타나 제련 시 노의 온도가 환원에 충분하지 못해 Fe의 회수율이 적었던 것으로 보이며 이 과정에서 광물에 포함된 K, P, Mg, Mn, Ti 등 불순물이 혼입되었다. Ca 함량이 높게 검출되는 곳이 있어 일부는 조제제로 석회물질을 넣었던 것으로 추정된다.

• 한국주조공학회지
• /
• 제39권1호
• /
• pp.7-13
• /
• 2019

Few studies of large blooms over 700 mm thick among those used for the forging of raw materials have been reported. The cooling rate difference between the surface and the center of a large bloom is large, and the degradation of the mechanical properties is likely in cases involving excessively coarse precipitates resulted from the slow cooling rate of a large bloom after casting. Therefore, a schematic investigation of the growth behaviors of precipitates while varying their locations in blooms is necessary. The dissolution behaviors of precipitates were investigated by simulating a reheating process during which the bloom is heated to a high temperature. The segregation behavior of the as-cast large bloom was also investigated. Reheating specimens were obtained after an isothermal heat treatment at $1150^{\circ}C$ with various holding times to simulate the reheating process, with the samples undergoing a subsequent water quenching step. The precipitates were extracted using an electrolytic extractor and a particle size analysis was conducted with the aid of SEM, EDS, and TEM. In the present work, Al oxide, MnS and Nb carbide were mainly observed.

• 한국재료학회지
• /
• 제26권10호
• /
• pp.528-534
• /
• 2016

The aim of this paper is to consider the effect of the manufacturing processes on corrosion and centerline cracking of ancient bronze spoons. The ancient bronze spoons in question were made by several steps of forging, in reheated condition with cast ingots. The manufacturing method is similar to that of the modern spoons. The investigations include observations from light and scanning electron microscopes of the microstructure in terms of the crack propagation. Cracks in the centerline are caused by solute segregation in the center-line region; this solute is solidified in the final stage of bronze spoon manufacture. Centerline cracking is also caused by ${\alpha}$ phase segregation, accompanied by forged overlapping along the longitudinal direction of the spoons. A vertical stripe with cracks along the centerline of the spoon's width is formed by folding in the wrought process. The overlapping area causes crack propagation with severe corrosion on the spoon surfaces over a period of a thousand years. The failure mechanisms of ancient bronze spoons may be similar to that of modern spoons, and the estimation of the failure mechanisms of ancient spoons can be appropriate to determine failure causes for such modern spoons.

• 박물관보존과학
• /
• 제16권
• /
• pp.56-81
• /
• 2015

족자 고리는 끈이나 유소를 고정시켜 걸 수 있도록 하는 장황 부속품으로 형태가 다양하며 여러 금속재를 사용하여 제작되었다. 현재 전통 형식의 고리는 대부분 개장으로 인해 유실되었으며, 일본식 고리를 사용하고 있다. 따라서 본 연구에서는 국립중앙박물관에 소장된 전통 족자 19점을 대상으로 고리의 형태와 제작기법, 성분을 조사하여 옛 형태를 복원해 보고자 하였다. 의궤 내용에서 고리는 원환(圓環), 국화동(菊花童), 배목(排目) 등 고유의 명칭으로 기록되어 있다. 휴대용 엑스선 형광분석기(portable X-ray fluorescence, Artax, Rontec)로 성분을 분석한 결과, 전통 형식의 고리는 황동, 철, 은-구리합금 등 다양한 금속재로 확인되었다. 구리와 아연이 주성분인 황동은 17점 족자 고리에 사용되었다. 전 윤시달 초상(신2339)의 배목에서는 철을 사용하였으며, 주석-납 합금으로 도금하였다. 이서구 초상(신1065)에서는 고리 전체가 은-구리합금으로 제작되었음을 확인하였다. 광학현미경(Leica, M205A)으로 제작 방법을 조사한 결과 원환은 금속봉을 절단한 뒤 둥글게 휘어 만든 유형과 주조로 제작된 유형으로 확인되었다. 배목은 주조한 합금으로 봉재나 판재를 만들고 다시 단조과정을 거쳐 제작하였고, 배목장식은 금속판재를 잘라 형태를 만든 후 축조와 타출기법 등으로 무늬를 새겨 장식하였다.