• Steel and Composite Structures
• /
• v.18 no.1
• /
• pp.71-90
• /
• 2015

Axial compression tests have been carried out on 18 rectangular concrete-filled cold-formed steel tubular (CFST) columns with the aim of investigating the axial behaviour of rectangular CFST columns under different loading methods (steel loaded-first and full-section loaded methods). The influence of different loading methods on the ultimate strength of the specimens was compared and the development of Poisson's Ratio as it responds to an increasing load was reported and analysed. Then, the relationship between the constraining factor and the strength index, and the relationship between the constraining factor and ductility index of the specimens, were both discussed. Furthermore, the test results of the full-section loaded specimens were compared with five international code predicted values, and an equation was derived to predict the axial carrying capacity for rectangular CFST columns with a steel loaded-first loading method.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.4
• /
• pp.205-212
• /
• 2005

This paper presents the application of system identification approaches for the load carrying capacity evaluation of composite PCI girder bridges based on the result of field test. For these problems, the moment of inertia of cross-sectional area and the natural frequency of bridge were used as structural parameters, the SAP2000 program for the structural analysis and the SLP method for the minimum error. As a result, it is found that the proposed algorithm for this study appears applicable to real structures with reasonable complexity. It is shown that the introduction of approximate quadratic equations is more realistic and timesaving than the common methods.

• The Korean Journal of Nuclear Medicine
• /
• v.16 no.2
• /
• pp.37-47
• /
• 1982

To evaluate fetal sex-hormonal status before delivery, testosterone and follicle stimulating normone(FSH) levels were measured in 64 amniotic fluid samples at midgestation by radioimmunoassay method. The mean concentration of testosterone in amniotic fluid of 37 cases carrying male fetus was 90.7 pg/ml and 27 cases carrying female fetus was 62.3 pg/ml. The mean :amniotic fluid FSH concentration of male fetus was 1.15 mIU/ml and of female fetus was 11.98 mIU/ml. The amniotic fluid testoserone and FSH concentrations had statistical difference between male and female fetuses. The ratio of testosterone over FSH in the amniotic fluid was 231.2 in male, 9.8 in female respectively and very significant difference was noticed. The levels of testosterone/FSH greater than 25 were found over 92% of male fetus and lesser than 25 were found over 92% female fetus. Measurement of testosterone and FSH especially testosterone/FSH ratio in amniotic fluid in midgestation may be an adjunct to other method of fetal sex determination.

• Journal of the Korean Society of Safety
• /
• v.24 no.5
• /
• pp.48-56
• /
• 2009

This paper presents the procedure for the optimal design of a PSC-I girder bridge considering life cycle cost (LCC). The load carrying capacity curves for the concrete deck, PSC-I girder and $\pi$-type pier were derived and used for the estimate of service lives. Total life cycle cost for the service life was calculated as sum of initial cost, damage cost, maintenance cost, repair and rehabilitation cost, user cost, and disposal cost. The advanced First Order Second Moment method was used to estimate the damage cost. The optimization method was applied to the design of PSC-I girder bridge. The objective function was set to the annual cost, which is defined by dividing the total life cycle cost by the service life, and constraints were formulated on the basis of Korean Standards. The optimal design was performed for various service lives and the effects of design factors were investigated.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.470-472
• /
• 2004

This paper proposes a method of increasing the Permissible current carrying capability of underground power cables. A clue of this method is driven from the temperature distribution analysis processes according to the currents calculated from unequally mode algorithm in ampacity program.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.3
• /
• pp.335-343
• /
• 1983

Modified-Shrink-Fit(MSF) method of compound cylinder is studied to increase elastic load carrying capacity (ELCC) of pressure vessel. The autofrettage and the shrink-fit processes are used to study the MSF process. Theoretical analyses based on the Tresca yield criterion, Hencky's total strain theory and elastic linearly strain-hardening material are carried out to derive closed form solutions. Experimental results are compared with theoretical results with various diameter ratios between outer (SM45C) and inner (SM20C) bloc cylinder. For various diameter ratios, increments of ELCC have errors in strains vs. internal loading pressures between experimental and theoretical results. But experimental results show good agreements with theoretical results in reyield pressurizing state. The increments of ELCC of compound cylinder manufactured by the MSF process is proved by measuring the residual stresses.

• Steel and Composite Structures
• /
• v.4 no.3
• /
• pp.211-226
• /
• 2004

This paper presents a study on the structural behaviour of modular steel scaffolds through both experimental and numerical investigations. Three one-storey and three two-storey modular steel scaffolds were built and tested to failure in order to examine the structural behaviour of typical modular steel scaffolds. Details of the tests and their test results were presented in this paper. Moreover, an advanced non-linear analysis method was employed to evaluate the load carrying capacities of these scaffolds under different support conditions. Comparisons between the experimental and the numerical results on the structural behaviour of these modular steel scaffolds were also presented. Moreover, the restraining effects of external supports in practical situations were also studied through finite element methods. The predicted load carrying capacities and deformations at failure of these models under partially restrained conditions were found to be close to the experimental results. A codified design method for column buckling with modified slenderness ratios was adopted for practical design of modular steel scaffolds.

• Tribology and Lubricants
• /
• v.10 no.1
• /
• pp.46-55
• /
• 1994

The static and dynamic analysis of air lubricatied tilting pad journal bearing which considers tilting effect of each pad, preload but which neglects pad inertia effect and deflection are performed. A direct numerical method is used in evaluating the static characteristics such as load carrying capacity, friction force and small peturbation method is used for calculation of dynamic characteristics. Stiffness and damping coefficients are compared with the variation of the preload. And these coefficients are slightly decreased with increased compressibility number under the constant bearing load carrying capacity.

• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.70-74
• /
• 2010

For each strand of wirerope sling, the international standards, ISO-8794, EN-13414 specify that the splice shall have five series of load carrying tucks. At least three of the load carrying tucks shall be made with the whole strand. And, the breaking force of the splice shall not be less than 70% or 80% of that of rope. But, There are no prescriptions for splicing types against different efficiency of each splicing type being used many workplace. In this study, analysis the work limit load efficiency according to variation of number of tucks and splicing types by experimental method As a result, the number of tucks 3+2 had the highest breaking efficiency.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.376-378
• /
• 1999

In order to design the current carrying conductor for GIS, it is important to predict temperature-rise when rated current flows. This paper deals with the coupling of Flux2D and analytic method to calculate the heat transfer coefficient. Heat transfer by conduction and convection is considered between the current carrying conductor and $SF_6$ gas. The result shows reasonable temperature distribution.