• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.495-498
• /
• 2002

Recently, the advent of electro-active papers (EAPap) actuators has been reported. In this paper, the possibility of the actuators is demonstrated. EAPap is a paper that produces large displacement with small force under an electrical excitation. EAPap is made with a chemically treated paper by constructing thin electrodes on both sides of the paper. When electrical voltage is applied on the electrodes the EAPap produces bending displacement. To improve the bending performance of EAPap, different paper fibers-softwood, hardwood, bacteria cellulose, cellophane, carbon mixture paper, electrolyte containing paper and Korean traditional paper, in conjunction with additive chemicals were tested. Two attempts were made to construct the electrodes: the direct use of aluminum foil and the gold sputtering technique. It was found that a cellophane paper exhibits a remarkable bending performance. When 2MV/m of excitation voltage was applied on the paper actuator, more than 3mm of tip displacement was observed out of the 30 mm long paper beam. This is quite low excitation voltage compared to that of other EAPs. The actuation principle of electro-active paper (EAPap) and possible applications are addressed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.172-172
• /
• 2011

현대 반도체 금속배선 연구에서는 기존에 쓰이던 Al (Aluminium) 금속배선 대신에 Cu(Copper) 금속배선 연구가 진행 되고 있다. Cu는 Al 보다 비저항이 낮고, 녹는점도 Al보다 높다는 장점이 있지만 저온에서 기판인 Si (Silicon) 과 반응하고 접착력이 우수하지 못 하다는 단점이 있다. 이런 문제를 해결하기 위하여 확산방지막을 기판과 금속배선 사이에 삽입하는 방법이 제시 되었다. 확산방지막으로는 기존에 쓰이던 Ti (Titanium) 계열의 확산방지막과 W (Tungsten) 계열의 확산방지막이 있다. 이번 연구에서는 W 계열의 확산방지막에 불순물 C (Carbon), N(Nitrogen)을 첨가한 W-C-N 확산방지막 시편을 제조하였고, N2의 비율을 변화시키며 $600^{\circ}C$ 열처리를 하였다. 실험 결과 질소의 포함 농도에 따라 확산방지막의 안정도가 변화한다는 결과를 얻었으며, 질소 첨가량에 따라 시편의 표면 보다는 시편의 중간층의 물성 변화율이 큰데 이는 시편 표면의 질소는 열처리 중 확산에 의한 시편과의 분리 현상이 일어나지만 시편의 중간층은 trap현상에 의하여 시편에 남아있어 질소의 영향을 받아 시편의 중간층이 더욱 질소 유량에 따른 영향이 큰 것을 확인하였다. 이 결과로부터 W-C-N 박막은 첨가된 질소의 유량에 따라 박막의 안정도가 결정된 다는 것을 알았다. 본 연구에서 시편은 rf magnetron sputtering 방법으로 제작하였고 연속압입 실험은 Hysitron사의 Triboindenter를 이용하였다. Indenting에 사용된 압입팁은 Berkovich tip을 사용하였다.

• Korean Journal of Materials Research
• /
• v.14 no.6
• /
• pp.425-431
• /
• 2004

A laser welding was applied between sintered tip of Fe-Co-W and low carbon steel shank for the diamond saw blade. The welding characteristics and formation of defects were investigated carefully for the weld fusion zone in different welding condition. Dendrite arm spacing in weld bead decreased with decrease of heat input. Co and W increased and Fe decreased in the weld fusion zone with increase of the heat input. The corresponding change of composition was observed with the change of beam position. The maximum and total length of crack decreased with increase of the heat input. The crack in weld bead was propagated along the dendrite boundary and was caused mainly by the segregation of constituent during the solidification.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.181-181
• /
• 2010

현대 반도체 금속배선 연구에서는 기존에 쓰이던 Al (Aluminium) 금속배선 대신에 Cu (Copper) 금속배선 연구가 진행되고 있다. Cu는 Al 보다 비저항이 낮고, 녹는점도 Al보다 높다는 장점이 있지만 저온에서 기판인 Si (Silicon) 과 반응하고 접착력이 우수하지 못 하다는 단점이 있다. 이런 문제를 해결하기 위하여 확산방지막을 기판과 금속배선 사이에 삽입하는 방법이 제시 되었다. 확산방지막으로는 기존에 쓰이던 Ti (Titanium) 계열의 확산방지막과 W (Tungsten) 계열의 확산방지막이 있다. 이번 연구에서는 W 계열의 확산방지막에 불순물 C (Carbon) 과 N (Nitrogen) 을 첨가한 W-C-N 확산방지막 시편을 제조하였고, N2의 비율을 변화시키며 $600^{\circ}C$, $800^{\circ}C$열처리를 하였다. 본 실험의 결과로, 확산방지막의 $N_2$ 농도가 0, 0.5, 2 sccm으로 증가할수록 고온에서도 Elastic modulus 와 Hardness 값이 시편의 여러 영역에서 비교적 안정적으로 유지된다는 결과를 얻었다. 이 결과로부터 W-C-N 박막의 질소 농도에 따라 고온에서도 비교적 안정적으로 유지된다는 결과를 얻었다. 본 연구에서 시편은 RF magnetron sputtering 방법으로 제작하였고 Elastic modulus와 Hardness의 측정은 Hysitron사의 Triboindenter를 이용하였다. Indenting에 사용된 압입팁은 Berkovich tip을 사용하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.1
• /
• pp.30-34
• /
• 2019

A newly proposed T-shape piezoelectric actuator, composed of piezoelectric benders, was designed and studied. This actuator has four legs, and can walk in both forward and backward directions. The piezoelectric actuator has a simple structure and can be easily fabricated. It consists of a piezoelectric bender and a joint. The piezoelectric bender is composed of carbon and ceramic materials. Therefore, there is an advantage in that it can be fabricated on a very small scale. Elliptical displacements of the piezoelectric actuators were analyzed by finite element analysis. Elliptical motion at the tip occurred at two voltages having a 90-degree phase difference. Based on the finite element analysis results, prototype actuators with maximum displacements were fabricated, and the characteristics of their movements were characterized.

• Steel and Composite Structures
• /
• v.47 no.3
• /
• pp.355-363
• /
• 2023

The main purpose of this study is to characterize the size-dependent strain rate sensitivity in structural steel using the continue stiffness measurement (CSM) indentation. A series of experiments, such as CSM indentation and optical microscope examination, has been performed at the room temperature at different rate conditions. The results indicated that indentation hardness, strain rate, and flow stress showed size-dependent behavior. The dependency of indentation hardness, strain rate, and flow stress on the indentation size was attributed to the transition of the dislocation nucleation rate and the dislocation behaviors during the indentation process. Since both hardness and strain rate showed the size-dependent behavior, SRS tended to depend on the indentation depth. The results indicated that the SRS was quite high over 2.0 at the indentation depth of 240 nm and quickly dropping to 0.08, finally around 0.046 at large indents. The SRS values at large indentations strongly agree with the general range reported for several types of low-carbon steel in the literature (Chatfield and Rote 1974, Nguyen et al. 2018b, Luecke et al. 2005). The results from the present study can be used in both static and dynamic analyses of structures as well as to assess and understand the deformation mechanism and the stress-state of material underneath the indenter tip during the process of the indentation testing.

• Coupled systems mechanics
• /
• v.12 no.2
• /
• pp.183-197
• /
• 2023

Scarce research has been published on crack propagation fracture of flywheels manufactured with carbon fiber-reinforced polymers. The present work deals with a calculation method to determine the conditions for which a crack propagates in the axial direction of the flywheel. The assumptions are: flywheels made with just a single thick ply or ply clustering laminates, oriented following the hoop direction; a single crack is analyzed in the plane defined by the hoop and axial directions; the crack starts close to one of the free edges; its axial length is initially large enough so that its tip is far away from that free edge, and the crack expands the entire circumferential perimeter and keeps its concentric position. The developed method provides information for a good design of flywheels. It is concluded that a fracture-based crack propagation criterion generally occurs at a lower speed than a stress-based criterion. Also, that the evolution of failure with thickness using the fracture criterion is exponential, demonstrating that thin flywheels are relatively not sensitive to crack propagation, whereas thick ones are very prone.

• Composites Research
• /
• v.32 no.6
• /
• pp.327-334
• /
• 2019

The delamination is a special mode of failure occurring in composite laminates. Several numerical studies with finite element analysis have been carried out on the delamination behavior of unidirectional composite laminates. On the other hand, the fracture for the multi-directional composite laminates may occur not only along the resin-fiber interface between plies known as interply or interlaminar fracture but also within a ply known as interyarn or intralaminar fracture accompanied by matrix cracking and fiber bridging. In addition, interlaminar and intralaminar cracks appear at irregular proportions and intralaminar cracks proceeded at arbitrary angle. The probabilistic analysis method for the prediction of crack growth behavior within a layer is more advantageous than the deterministic analysis method. In this paper, we analyze the crack path when the mode I load is applied to the cross-ply carbon/epoxy composite laminates and collect and analyze the probability data to be used as the basis of the probabilistic analysis in the future. Two criteria for the theoretical analysis of the crack growth direction were proposed by analyzing the stress field at the crack tip of orthotropic materials. Using the proposed method, the crack growth directions of the cross-ply carbon/epoxy laminates were analyzed qualitatively and quantitatively and compared with experimental results.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• Structural Engineering and Mechanics
• /
• v.63 no.3
• /
• pp.361-370
• /
• 2017

Through the use of finite element analysis and acoustic emission techniques we have evaluated the interfacial failure of a carbon fiber reinforced polymer (CFRP) repair patch on a notched aluminum substrate. The repair of cracks is a very common and widely used practice in the aeronautics field to extend the life of cracked sheet metal panels. The process consists of adhesively bonding a patch that encompasses the notched site to provide additional strength, thereby increasing life and avoiding costly replacements. The mechanical strength of the bonded joint relies mainly on the bonding of the adhesive to the plate and patch stiffness. Stress concentrations at crack tips promote disbonding of the composite patch from the substrate, consequently reducing the bonded area, which makes this a critical aspect of repair effectiveness. In this paper we examine patch disbonding by calculating the influence of notch tip stress on disbond area and verify computational results with acoustic emission (AE) measurements obtained from specimens subjected to uniaxial tension. The FE results showed that disbonding first occurs between the patch and the substrate close to free edge of the patch followed by failure around the tip of the notch, both highest stress regions. Experimental results revealed that cement adhesion at the aluminum interface was the limiting factor in patch performance. The patch did not appear to strengthen the aluminum substrate when measured by stress-strain due to early stage disbonding. Analysis of the AE signals provided insight to the disbond locations and progression at the metal-adhesive interface. Crack growth from the notch in the aluminum was not observed until the stress reached a critical level, an instant before final fracture, which was unaffected by the patch due to early stage disbonding. The FE model was further utilized to study the effects of patch fiber orientation and increased adhesive strength. The model revealed that the effectiveness of patch repairs is strongly dependent upon the combined interactions of adhesive bond strength and fiber orientation.