• Korean Journal of Materials Research
• /
• v.27 no.4
• /
• pp.184-191
• /
• 2017

This present study deals with the effect of micro-alloying elements and transformation temperature on the correlation of microstructure and tensile properties of low-carbon steels with ferrite-pearlite microstructure. Six kinds of low-carbon steel specimens were fabricated by adding micro-alloying elements of Nb, Ti and V, and by varying isothermal transformation temperature. Ferrite grain size of the specimens containing mirco-alloying elements was smaller than that of the Base specimens because of pinning effect by the precipitates of carbonitrides at austenite grain boundaries. The pearlite interlamellar spacing and cementite thickness decreased with decreasing transformation temperature, while the pearlite volume fraction was hardly affected by micro-alloying elements and transformation temperature. The room-temperature tensile test results showed that the yield strength increased mostly with decreasing ferrite grain size and elongation was slightly improved as the ferrite grain size and pearlite interlamellar spacing decreased. All the specimens exhibited a discontinuous yielding behavior and the yield point elongation of the Nb4 and TiNbV specimens containing micro-alloying elements was larger than that of the Base specimens, presumably due to repetitive pinning and release of dislocation by the fine precipitates of carbonitrides.

• Journal of Surface Science and Engineering
• /
• v.30 no.1
• /
• pp.23-32
• /
• 1997

The electrolytic boronizing on carbon steels in the mixture of $Na_2B_4O_7$ and NaCl was conducted at 750~$950^{\circ}C$ for 1~6 hours under 0.5A/$\textrm{cm}^2$ current density. The micorostructrure and microheredness of boronized layer was also studien. The effect of the additive such as $CaCl_2$ or NaOH on the formation of boronized layer was also investigated. The boronized layer were composed of two sublayers, i.e., FeB and $Fe_2B$ , which have tooth structure. the average layer thinknesses of the low carbon steel and SM45C boronized at $900^{\circ}C$ for 4hours were 153 and 138 $\mu\textrm{m}$, respectively. The thickness of the twosublayers was significantly increased with increasing boronizing temperature. To obtain a single $Fe_2B$ layer without FeB sublayer, the boronized materials ware homegenized at $950^{\circ}C$ for 4 hours. It was fount that the single layer with a microhardness Hv$\thickapprox$ 1120 -1250 was formed. The calculated activation energies for formation of boronized layer on the low carbon steel and SM45C were 18.7 and 12.6 Kcal/mol, respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.40-43
• /
• 2009

This study is for investigating the effect of induction heating with various alloy elements to manufacture the pre-heat treated steels of 100kgf/$mm^2$ for cold heading. For four kinds of steels, the condition of induction heating (especially, induction tempering) were observed, and their microstructure and tensile and compressive properties were investigated. The middle carbon steel and the low carbon Cr-Mo steel are needed the higher Grange-Baughman tempering parameter than that of the low carbon Cr steel to obtain 100kgf/$mm^2$ tensile strength. For accomplishing the pre-heat treated steel of 100kgf/$mm^2$ tensile strength having advanced cold heading. It is needed that the pre-heat treated steel is manufactured by induction quenching and tempering with the low carbon alloy steel to have the high ratio of ferrite and the fine globular cementite simultaneously.

• Corrosion Science and Technology
• /
• v.13 no.1
• /
• pp.1-5
• /
• 2014

A low carbon steel, Fe-2.25%Cr steel (ASTM T22), and Fe-2.25%Cr-1.6%W steel (ASTM T23) were aluminized by hot dipping into molten Al baths. After hot-dipping, a thin Al-rich topcoat and a thick alloy layer formed on the surface. The topcoat consisted primarily of a thin Al layer that contained a small amount of Fe, whereas the alloy layer consisted of Al-Fe intermetallics such as $Al_5Fe_2$ and AlFe. Cr, Mo, and W in T22 and T23 steels reduced the thickness of the topcoat and the alloy layer, and flattened the reaction front of the aluminized layer, when compared to the low carbon steel.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.91-94
• /
• 2008

Newly developed Atom Probe Tomography (APT) technique can provide the highest available spatial resolution, 3D tomography imaging and quantitative chemical analysis in a sub-nm scale. As a complementary technique to APT, Nano-secondary ion Mass Spectroscopy (SIMS) also provides the boron distribution in micro-scale. Therefore, the exact behavior of boron at either grain boundary or grain interior in steels can be investigated by the combination of APT and SIMS techniques from the sub-nanometer scale to the micrometer scale. The results obtained by both APT and SIMS revealed that the boron atoms were mainly segregated to the grain boundaries rather than to the grain interior in the steels containing 50ppm and 100ppm boron. It also found that carbon atoms were segregated at the boron enriched regions, which were thought to be retained austenite phase due to the chemical composition of carbon atoms.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.157-158
• /
• 2002

A surface hardenable low alloy carbon steel was implanted with medium energy (20 - 50KeV) $N_2^+$ ions to produced a modified hardened surface. The implantation conditions were varied and are given in several doses. The surface hardness of treated and untreated steels were measured using depth sensing ultra micro indentation system (UMIS). It is shown that the hardness of nitrogen ion implanted steels varied from 20 to 50GPa depending on the implantation conditions and the doses of implantation. The structure of the modified surfaces was examined by X-ray photoelectron spectroscopy (XPS). It was found that the high hardness on the implanted surfaces was as a result of formation of non-equilibrium nitrides. High-resolution XPS studies indicated that the nitride formers were essentially C and Si from the alloy steel. The result suggests that the ion implantation provided the conditions for a preferential formation of C and Si nitrides. The combination of evidences from nano-indentation and XPS, provided a strong evidence for the existence of $sp^3$ type of bonding in a suspected $(C,Si)_xN_y$ stoichiometry. The formation of ultra hard surface from relatively cheap low alloy steel has significant implication for wear resistance implanted low alloy steels.

• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.1
• /
• pp.9-20
• /
• 1999

The effect of post oxidation, water-quenched after holding in air for 5~420 seconds or cooling or furnace cooling, on corrosion resistance and phase formation characteristics of the surface layer of SM20C and SM45C carbon steels after gas nirtrocarbursing in the $NH_3-5%CO_2-N_2$ gas atmosphere at $580^{\circ}C$ for 3hours is studied. The compound layers of two steels consist of ${\varepsilon}-Fe_{2-3}N$, ${\gamma}^{\prime}-Fe_4N$ and $Fe_3O_4$, phases, however, the quantity of ${\gamma}^{\prime}-Fe_4N$ phase increases for the furnace cooled specimen compared to that of air cooling specimen. With increasing $NH_3$ content in the gas mixture and also increasing the keeping time in the air after gas nitrocarburising, the ${\varepsilon}-Fe_{2-3}N$ phase of compound layer increases, while the decreased current density recognizing the improvement of corrosion resistance are shown. the passive current density of SM45C steel is lower than that of SM20C steel at the same nitrocarburising conditions.

• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.4
• /
• pp.327-337
• /
• 1999

A series of Ni-Cr-Mo alloy steels were austenitized, quenched to martensite, and tempered at various temperature and time conditions. Tensile testing was conducted at room temperature with cylindrical specimens, and hardness was measured using Rockwell hardness tester. In the tempering stage I, high strain hardening and yield strength accounted for the high ultimate strength and hardness. In the tempering stage II, strengths and hardness linearly decreased with increasing tempering temperature. Specimens tempered in the temperin stage III showed incipient discontinuous yielding and tensile strengths only slightly higher than yield strengths. Ductilities decreased slightly in specimens tempered in the tempered martensite embrittlement range, and severely decreased in specimens tempered for 10 hours at $500^{\circ}C$ in the temper embrittlement range. Specimens tempered at $600^{\circ}C$ for 10 hours showed recrystallized microstructures, a number of fine dimples, and increased strain hardening, probably due to the precipitation of alloy carbides. The simple formulae for the mechanical properties of these steels were suggested as a function of carbon content and Hollomon-Jaffe tempering parameter.

• Korean Journal of Materials Research
• /
• v.26 no.10
• /
• pp.535-541
• /
• 2016

The present study deals with the effects of micro-alloying elements such as Ni, V, and Ti on the recrystallization behavior of carbon steels at different strain rates. Eight steel specimens were fabricated by varying the chemical composition and reheating temperature; then, a high-temperature compressive deformation test was conducted in order to investigate the relationship of the microstructure and the recrystallization behavior. The specimens containing micro-alloying elements had smaller prior austenite grain sizes than those of the other specimens, presumably due to the pinning effect of the formation of carbonitrides and AlN precipitates at the austenite grain boundaries. The high-temperature compressive deformation test results indicate that dynamic recrystallization behavior was suppressed in the specimens with micro-alloying elements, particularly at increased strain rate, because of the pinning effect of precipitates, grain boundary dragging and lattice misfit effects of solute atoms, although the strength increased with increasing strain rate.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.106-113
• /
• 2007

The effect of chemical composition on the microstructural change and tensile property in TRIP-assisted steels with different chemical composition was investigated by using SEM, TEM, XRD and UTM. As a result of microscopic observation, the morphology of retained austenite could be identified as two types : a granular type in a steel containing higher sillicon and a film type in a steel having higher carbon. For the case of higher carbon-containing steel with a tensile strength of 860 MPa and a total elongation of 38%, film-typed retained austenite could be observed between lath bainitic ferrite. Actually, metastable retained austenite was a requisite for the good formability, which means that chemical composition plays a significant role in the microstructure and tensile property of TRIP-assisted steels. With respect to tensile property, the steels containing suitable silicon and manganese, respectively, showed a typical TRIP effect in stress-strain curve, while a steel containing higher manganese content exhibited the assimilar behavior shown in dual phase steel.