• Journal of Electrochemical Science and Technology
• /
• v.9 no.3
• /
• pp.220-228
• /
• 2018

This study introduced a carbon-free electrode for $Li-O_2$ cells with the aim of suppressing the side reactions activated by carbon material. Micro-particles of poly(3,4-ethylenedioxythiophene) (PEDOT), a conducting polymer, were used as the base material for the air electrode of $Li-O_2$cells. The PEDOT micro-particles were treated with $H_2SO_4$ to improve their electronic conductivity, and LiBr and CsBr were used as the redox mediators to facilitate the dissociation of there action products in the electrode and reduce the over-potential of the $Li-O_2$ cells. The capacity of the electrode employing PEDOT micro-particles was significantly enhanced via $H_2SO_4$ treatment, which is attributed to the increased electronic conductivity. The considerable capacity enhancement and relatively low over-potential of the electrode employing $H_2SO_4$-treated PEDOT micro-particles indicate that the treated PEDOT micro-particles can act as reaction sites and provide storage space for the reaction products. The cyclic performance of the electrode employing $H_2SO_4$-treated PEDOT micro-particles was superior to that of a carbon electrode. The results of the Fourier-transform infrared spectroscopic analysis showed that the accumulation of residual reaction products during cycling was significantly reduced by introducing the carbon-free electrode based on $H_2SO_4$-treated PEDOT micro-particles, compared with that of the carbon electrode. The cycle life was improved owing to the effect of the redox mediators. The refore, the use of the carbon -free electrode combined with redox mediators could realize excellent cyclic performance and low over-potential simultaneously.

• Journal of Hydrogen and New Energy
• /
• v.28 no.2
• /
• pp.206-211
• /
• 2017

Carbon felt electrode for the vanadium redox-flow battery (VRFB) has been studied to see the effect of grephene oxide (GO) treatment on the surface of the carbon felt electrode. In this paper, surface of carbon felt electrodes were treated with various concentrations of grephene oxide. Electrochemical analysis, cyclic voltammetry (CV), was performed to investigate redox characteristics as electrode for VRFB. Also the effect of GO on the introduction of functional group on the surface of carbon felt electrodes were investigated using X-ray photoelectron spectroscopy (XPS), which discovered increase in the overall functional group content on the surface of carbon felts.

• Journal of Surface Science and Engineering
• /
• v.52 no.3
• /
• pp.150-155
• /
• 2019

The carbon electrode was modified through manganese-catalyzed hydrogenation method for high energy density vanadium redox flow battery (VRFB). During the catalytic hydrogenation, the manganese oxide deposited at the surface of the carbon electrode stimulated the conversion reaction from carbon to methane gas. This reaction causes the penetration of the manganese and excavates a number of cavities at electrode surface, which increases the electrochemical activity by inducing additional electrochemically active site. The formation of the porous surface was confirmed by the scanning electron microscopy (SEM) images. Finally, the electrochemical performance test of the electrode with the porous surface showed lower polarization and high reversibility in the cathodic reaction compared to the conventional electrode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.26-30
• /
• 2000

In this paper, carbon and silver electrode properties of power electroluminescent device were investigated. Devices were manufactured by screen-printing and manufactured devices were measured following things with variable applied voltage; emission spectra, transferred charge density, brightness and current. A continuous test at $65 ^{\circ}C$ of temperature and 95% of humidity was operated. The brightness of devices which were made of silver and carbon electrode at 100V was $67.03cd/m^2$ and $60.02cd/m^2$ respectively. In case of device, which was made of silver electrode, a black spot was formed after 72 hours and degraded but carbon electrode was stable.

• Carbon letters
• /
• v.1 no.1
• /
• pp.27-30
• /
• 2000

Performance of direct methanol fuel cell using high porous active carbon as an uncatalysed diffusion layer in anode (composite electrode) has been evaluated. Effects of porous active carbon in anode were investigated by galvanostatic method and Fourier Transform Infrared spectroscopy. The single cell was operated with 2.5 M methanol at temperature of $80-120^{\circ}C$ and showed performance of $210-510\;mA/cm^2$ at 0.4V. By replacing conventional electrode with composite electrode, the increment of $290\;mA/cm^2$ in current density was obtained at $90^{\circ}C$and 0.4V. The potential decay of the single cell was about 14.5% for 20 days operation.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.1
• /
• pp.111-131
• /
• 2024

Lignin-derived porous carbon has been identified as a versatile electrode material for supercapacitors (SCs) in energy storage systems (ESSs) owing to their intrinsic advantages including good electrical conductivity, low cost, high thermal and chemical stability, and high porosity, which stem from high surface, appropriate pore distribution, tailored morphologies, heterostructures, and diverse derivates. In this review, to provide a fundamental understanding of the properties of lignin, we first summarize the origin, historical development, and basic physicochemical properties. Next, we describe essential strategies for the preparation of lignin-derived porous carbon electrode materials and then highlight the latest advances in the utilization of lignin-derived porous carbon materials as advanced electrode materials. Finally, we provide some of our own insights into the major challenges and prospective research directions of lignin-derived porous carbon materials for supercapacitors. We believe that this review will provide general guidance for the design of next-generation electrode materials for supercapacitors.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.2
• /
• pp.54-61
• /
• 2013

This paper presents transient response behavior and frequency-dependent ground impedance of a single carbon ground electrode. The ground impedance of the carbon ground electrode was measured as a function of frequency of injected currents and simulated by using the distributed parameter circuit model with due regard to the frequency-dependent soil parameters, and the transient response behavior of the carbon ground electrode against impulse currents were investigated. As a consequence, the frequency-dependent ground impedance of the carbon ground electrode showed the capacitive behavior, that is, the ground impedance decreases with increasing the frequency of injected currents and lowers at the fast front time of impulse current. It was found that the carbon ground electrode is effective in grounding system for lightning protection. The ground impedance simulated with due regard to the frequency-dependent soil parameters was in good agreement with the measured data. The adequacy of the simulation technique and the distributed parameter circuit model for the carbon ground electrode was verified. It is expected that the simulation methodology, which analyzes the frequency-dependent ground impedance of the carbon ground electrode proposed in this work, can be used in the design of a grounding system for protection against lightning.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.355-356
• /
• 2006

This work describes the effect of the number of roll pressing and the composition of carbon black on the electric and mechanical properties of carbon-PTFE electrode, in which composition is MSP20 : carbon black: PTFE = 95-X : X : 5 wt.%. It was found that the best electric and mechanical properties were obtained for sheet electrode roll pressed about 15 times and for sheet electrode, in which composition is MSP20 carbon black : PTFE = 80 : 15 : 5 wt%. These behaviors could be explained by the network structure of PTFE fibrils and conducting paths linked with carbon blacks, respectively. On the other hand, cell capacitor using the sheet electrode with 15 wt.% of carbon black attached on aluminum current collector with the electric conductive adhesive, in composition is carbon black : CMC = 70 : 30 wt.%, has exhibited the best rate capability between 0.5 $mA/cm^2$ ~ 100 $mA/cm^2$ current density and the lowest ESR.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.541-542
• /
• 2006

This work describes the effect of the number of roll pressing and the composition of carbon black on the electric and mechanical properties of carbon-PTFE electrode, in which composition is MSP 20 : carbon black : PTFE = 95-X : X : 5 wt.%. It was found that the best electric and mechanical properties were obtained for sheet electrode roll pressed about 15 times and for sheet electrode, in which composition is MSP 20 : carbon black : PTFE = 80 : 15 : 5 wt.%. These behaviors could be explained by the network structure of PTFE fibrils and conducting paths linked with carbon blacks, respectively. On the other hand, cell capacitor using the sheet electrode with 15 wt.% of carbon black attached on aluminum current collector with the electric conductive adhesive, in composition is carbon black : CMC = 70 : 30 wt.%, has exhibited the best rate capability between $0.5mA/cm^2{\sim}100mA/cm^2$ current density and the lowest ESR.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.615-619
• /
• 2018

To produce carbon electrodes for use in perovskite solar cells, electrode samples are prepared by mixing various weight ratios of 35 nm nano carbon(NC) and $1{\mu}m$ graphite flakes(GF), GF/(NC+GF) = 0, 0.5, 0.7, and 1, in chlorobenzene(CB) solvent with a $ZrO_2$ binder. The carbon electrodes are fabricated as glass/FTO/carbon electrode devices for microstructure characterization using transmission electron microscopy, optical microscopy, and a field emission scanning electron microscopy. The electrical characterization is performed with a four-point probe and a multi tester. The microstructure characterization shows that an electrode with excellent attachment to the substrate and no surface cracks at weight ratios above 0.5. The electrical characterization results show that the sheet resistance is <$70{\Omega}/sq$ and the interface resistance is <$70{\Omega}$ at weight ratios of 0.5 and 0.7. Therefore, a carbon paste electrode with microstructure and electrical properties similar to those of commercial carbon electrodes is proposed with an appropriate mixing ratio of NC and GF containing a CB solvent and $ZrO_2$.