• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1514-1519
• /
• 2001

This paper is concerned with design, manufacturing and performance test of LIPCA ( Lightweight Piezo- composite Curved Actuator) using a top carbon fiber composite layer with near -zero CTE(coefficient of thermal expansion), a middle PZT ceramic wafer and a bottom glass/epoxy layer with high CTE. The main point of this design is to replace the heavy metal layers of THUNDER by thigh tweight fiber reinforced plastic layers without losing capabilities to generate high force and large displacement. It is possible to save weight up to about 30% if we replace the metallic backing material by the light fiber composite layer. We can also have design flexibility by selecting the fiber direction and the size of prepreg layers. In addition to the lightweight advantage and design flexibility, the proposed device can be manufactured without adhesive layers when we use epoxy resin prepreg system. Glass/epoxy prepregs, a ceramic wafer with electrode surfaces, and a graphite/epoxy prepreg were simply stacked and cured at an elevated temperature (177 $^{circ}C$ after following an autoclave bagging process. It was found that the manufactured composite laminate device had a sufficient curvature after detached from a flat mold. The analysis method of the cure curvature of LIPCA using the classical lamination theory is presented. The predicted curvatures are fairly in agreement with the experimental ones. In order to investigate the merits of LIPCA, a performance test of both LIPCA and THUNDE$^{TM}$ were conducted under the same boundary conditions. From the experimental actuation tests, it was observed that the developed actuator could generate larger actuation displacement than THUNDERT$^{TM}$.

• Journal of Korean Society on Water Environment
• /
• v.33 no.6
• /
• pp.722-727
• /
• 2017

Livestock manure is known to be the main cause of non-point pollution in agricultural areas. The pollutant reduction ratio of livestock manure recycling to fertilizers was measured in order to analyze the effect on the water quality of the Total Maximum Daily Load (TMDL) system in Korea. The reduction ratio has been applied by theoretical consideration without a survey, and there is no value for Total Organic Carbon (TOC) newly introducing any organic items. The reduction ratio of each pollutant from this study was revealed as follows: TOC, BOD, T-N and T-P were 0.34, 0.60, 0.37, and 0.42 for individual farm and 0.38, 0.61, 0.45 and 0.44 for entrustment facilities, respectively. The reduction ratio of individual farm was surveyed as TOC 0.63, BOD 0.62, T-N 0.42 and T-P 0.32 for liquid fertilizer, and TOC 0.30, BOD 0.64, T-N 0.40 and T-P 0.48 for compost. The total reduction ratio was derived by multiplying the ratio for liquid fertilizer and compost by the respective load. Compared to the pollutant reduction ratio of the individual farm with entrustment facilities marking the higher in liquid fertilizer and the lower in compost. Through this study, we found the difference of pollutant reduction ratio between a livestock manure recycling process and facilities. Although phosphorus is known as a preservative matter, the treatment efficiency of T-P is analyzed to decrease by chemical precipitation.

• Steel and Composite Structures
• /
• v.23 no.6
• /
• pp.727-736
• /
• 2017

The application of carbon fiber reinforced polymer (CFRP) in steel structures primarily includes two categories, i.e., the bond-critical application and the contact-critical application. Debonding failure and buckling failure are the main failure modes for these two applications. Conventional electrometric techniques may not provide precise results because of the limitations associated with single-point contact measurements. A nondestructive full-field measurement technique is a valuable alternative to conventional methods. In this study, the digital image correlation (DIC) technique was adopted to investigate the bond behavior and buckling behavior of CFRP-steel composite members. The CFRP-to-steel bonded joint and the CFRP-strengthened square hollow section (SHS) steel column were tested to verify the suitability of the DIC technique. The stereo-DIC technique was utilized to measure continuous deformation. The bond-slip relationship of the CFRP-to-steel interface was derived using the DIC data. Additionally, a multi-camera DIC system consisting of four stereo-DIC subsystems was proposed and applied to the compressive test of CFRP-strengthened SHS steel column. The precise buckling location and CFRP delamination of the CFRP-strengthened SHS steel column were identified. The experimental results confirm that the stereo-DIC technique can provide effective measurements for investigating the behaviors of CFRP-steel composite members.

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.197-204
• /
• 1993

Abstract The effects of the hole size and the specimen width on the fracture behavior of several fabric composite plates are experimentally investigated in tension. Tests are performed on plain woven glass/ epoxy, plain woven carbon/epoxy and satin woven glass/polyester specimens with a circular hole. It is shown in this paper that the characteristic length according to the point stress criterion depends on the hole size and the specimen width. An excellent agreement is found between the experimental results and the analytical predictions of the modified failure criterion. The notched strength increase with an increase in the damage ratio, which is explained by a stress relaxation due to the formation of damage zone. When the unstable fracture occurred, the critical crack length equivalent for the damage zone is about twice the characteristic length. The critical energy release rate $G_c$ is independent of hole size for the same specimen width. The variation of $G_c$ according to the material system, fiber volume fraction and specimen width relates to the notch sensitivity factor. $G_c$ increases with a decrease in the notch sensitivity factor, which can be explained by a stress relaxation due to the increase of damage zone.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.7
• /
• pp.1032-1038
• /
• 2017

Recently, regulation on carbon emissions has been strengthened according to the new climate change convention (COP21) held in Paris, and then Korea has decided to reduce CO2 emissions by 37% until 2030. As one of countermeasures, the government has energetically performed demonstration projects of island micro-grid including solar power, wind power and energy storage system. However, in order to smoothly introduce island micro-grid, it is a critical issue to carry out the economic evaluation for power utility aspect and independent power producer aspect. Therefore, this paper proposes economic evaluation algorithms of island micro-grid which are based on the present worth method, considering cost and benefit factors in the aspect of both sides. Firstly, in case of power utility this paper proposes algorithm to estimate a period of return on investment according to the introduction capacity of distributed generators replacing diesel generator. And also, in case of independent power producer, this paper proposes evaluation algorithm to estimate weighting factor of SMP and benefit rate based on break-even point related with cost and benefit. From a case study result on real island micro-grid model, it is confirmed that proposed algorithms are useful and practical for the economic evaluation of island micro-grid.

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.67-74
• /
• 2022

Injection molding is a cyclic process comprising of cooling phase as the largest part of this cycle. Providing efficient cooling in lesser cycle times is of significant importance in the molding industry. Recently, lots of researches have been done for rapid cooling of a hot-spot area using CO2 in injection molding. The CO2 flows under high pressure through small, flexible capillary tubes to the point of use, where it expands to create a snow and gas mixture at a temperature of -79℃. The gaseous CO2 removes heat from the mold and releases it into the atmosphere. In this paper, a CO2 cooling module was applied to an injection mold in order to cool a large area cavity uniformly and quickly, and the cooling performance of the injection mold was investigated. The product was a high-curvature molded part with a molding area of 300x100mm. Heat cartridges were installed in a stationary mold, and CO2 cooling module was inserted inside a movable mold. Through structural analysis, it was confirmed that the maximum deformation of mold with CO2 cooling module was 0.09mm. A CO2 feed system with a heat exchanger was used for cooling experiments. The CO2 was injected into the holes on both sides of the supply pipe of the cooling module and discharged through hexagon blocks to cool the mold. It took 5.8 seconds to cool the mold from an average temperature of 140℃ to 70℃. Through the experiment using CO2 cooling module, it was found that a cooling rate of up to 12.98℃/s and an average of 10.18℃/s could be achieved.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2812-2822
• /
• 2023

The supercritical carbon dioxide (sCO₂) Brayton power cycle is more effective than the conventional power cycle and is more widely applicable to heat sources. The inlet working conditions of the compressor have a higher influence on their operating performance because the thermophysical properties of the CO₂ vary dramatically close to the critical point. The flow in the sCO₂ compressor is simulated and the compressor performance is analyzed. The results show that the sCO₂ centrifugal compressor operates outside of its intended parameters due to the change in inlet temperature. The sCO₂ compressor requires more power as the inlet temperature increases. The compressor power is 582 kW when the inlet temperature is at 304 K. But the power is doubled when the inlet temperature increases to 314 K, and the change in the isentropic efficiency is within 5%. The increase in the inlet temperature significantly reduces the risk of condensation in centrifugal compressors. When the heat load of the sCO₂ power system changes, the inlet pressure to the turbine can be kept constant by regulating the rotational speed of compressors. With the increase in rotational speed, the incidence loss and condensation risk increase.

• Journal of Internet Computing and Services
• /
• v.24 no.5
• /
• pp.107-120
• /
• 2023

The public bicycle of Seoul, Ttareungyi, was launched at October 2015 to reduce traffic and carbon emissions in downtown Seoul and now, 2023 Oct, the cumulative number of user is upto 4 million and the number of bike is about 43,000 with about 2700 stations. However, super growth of Ttareungyi has caused the several problems, especially demand/supply mismatch, and thus the Seoul citizen has been complained about out of stock. In this point, this study conducted a real time demand forecasting model to prevent stock out bike at stations. To develop the model, the research team gathered the rental·return transaction data of 20,000 bikes in whole 1600 stations for 2019 year and then analyzed bike usage, user behavior, bike stations, and so on. The forecasting model using machine learning is developed to predict the amount of rental/return on each bike station every hour through daily learning with the recent 90 days data with the weather information. The model is validated with MAE and RMSE of bike stations, and tested as a prototype service on the Seoul Bike Management System(Mobile App) for the relocation team of Seoul City.

• Journal of the Korean Society of Tobacco Science
• /
• v.24 no.1
• /
• pp.67-73
• /
• 2002

In light of addressing consumer health concern, coping with anti-tobacco movement, and promoting new product, tobacco industry is actively pursuing to make a new generation of cigarettes with low tar and nicotine deliveries, and less harmful substances. Low tar and low nicotine cigarettes increases their market shares dramatically world wide, especially in KT&G, multinational tobacco companies, EU countries, even in China regulated by CNTC to set up yearly target to lower tar and nicotine deliveries. On the other hand, to design a new cigarette with reduced harmful substances begins to gain speed. The "modified Hoffmann list" publishes thirty plus substances in tobacco leaf and main smoke stream, which is the prime suspect causing health problems. Various ways and means are developed to reduce such components including new tobacco breeds, new curing method, tobacco leaf treatment before processing, selected filtration system, innovated casing system to reduce free radicals, as well as some non conventional cigarette products. In TSRC held this year, the main topic is related to reduce tobacco specific nitrosamines in tobacco leaf. The new generation of cigarette is in the horizon. It still needs a lot help to produce commercial products with satisfied taste and aroma characters. The flavor industry is not regulated by many governments demanding which ingredients might or might not be for tobacco use. However, most of the cigarette companies self impose a list of ingredients to guide flavor suppliers to design flavors. Unfortunately, the number of ingredients in those lists is getting shorter every year. It is understandable that the health is not the only reason. Some cigarette companies are playing safe to protect the company from potential lawsuit, while others are just copying from their competitors. Moreover, it is obvious that it needs more assistance from casings and flavors to design new generation of cigarettes with missing certain flavor components in tobacco leaf and main smoke stream. These flavor components are either non-existed or at lower level at new form of cured tobacco leaf or filtered in the main smoke stream along with reduced harmful substances. The use of carbon filters and other selected filtration system poses another tough task for flavor system design. Specific flavor components are missing from the smoke analysis data, which brings a notion of "carbon taste" and "dryness" of mouth feel. It is ever more demanded by cigarette industry to flavor suppliers to produce flavors as body enhancer, tobacco notes, salivating agents, harshness reducer, and various of aromatic notes provided they are safe to use. Another trend is that water based flavor or flavor with reduced ethanol as solvent is gaining popularity. It is preferred by some cigarette companies that the flavor is compounded with all natural ingredients or all ingredients should he GMO free. The new generation of cigarettes demands many ways of new thinking process. It is also vital for tobacco industry. It reflects the real needs for the consumers that the cigarette product should be safe to use as well as bearing the taste and aroma characters smokers always enjoyed. An effective tobacco flavor system is definitely a part of the equation. The global trend of tobacco industry is like trends of any other industries lead by consumer needs, benefited with new technology availability, affected by the global economy, and subjected for various rules and regulations. Anti-tobacco organizations and media exceptionally scrutinize cigarette, as a legal commercial product. Cigarette is probably the most studied commercial product for its composition, structure, deliveries, effects, as well as its new developmental trend. Therefore, any new trend of cigarette development would be within these boundaries. This paper is trying to point out what it would be like for tobacco industry in the next few yews and what concerns the tobacco industry. It focuses mostly on the efforts to produce safer cigarettes. It is such a vital task for the tobacco industry and its affiliate industries such as cigarette papers, filters, flavors, and other materials. The facts and knowledge presented in this paper might be well known for the public. Some of the comments and predictions are very much personal opinion for a further discussion.

• Journal of Sensor Science and Technology
• /
• v.14 no.2
• /
• pp.69-77
• /
• 2005

The electronic nose (e-nose) has been used in food industry and quality controls in plastic packaging. Recently it finds its applications in medical diagnosis, specifically on detection of diabetes, pulmonary or gastrointestinal problem, or infections by examining odors in the breath or tissues with its odor characterizing ability. Moreover, the use of portable e-nose enables the on-site measurements and analysis of vapors without extra gas-sampling units. This is expected to widen the application of the e-nose in various fields including point-of-care-test or e-health. In this study, a PDA-based portable e-nose was developed using micro-machined gas sensor array and miniaturized electronic interfaces. The rich capacities of the PDA in its computing power and various interfaces are expected to provide the rapid and application specific development of the diagnostic devices, and easy connection to other facilities through information technology (IT) infra. For performance verification of the developed portable e-nose system, Six different vapors were measured using the system. Seven different carbon-black polymer composites were used for the sensor array. The results showed the reproducibility of the measured data and the distinguishable patterns between the vapor species. Additionally, the application of two typical pattern recognition algorithms verified the possibility of the automatic vapor recognition from the portable measurements. These validated the portable e-nose based on PDA developed in this study.