• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.325-330
• /
• 2015

Performance of solid oxide fuel cells (SOFCs), in comparison with that under hydrogen fuel, were investigated under direct internal reforming conditions. Anode supported cells were fabricated with an Ni+YSZ anode, YSZ electrolyte, and LSM+YSZ cathode for the present work. Measurements of I-V curves and impedance were conducted with S/C (steam to carbon) ratio of ~ 2 at $800^{\circ}C$. The outlet gas was analyzed using gas chromatography under open circuit condition; the methane conversion rate was calculated and found to be ~ 90% in the case of low flow rate of methane and steam. Power density values were comparable for both cases (hydrogen fuel and internal steam reforming of methane), and in the latter case the cell performance was improved, with a decrease in the flow rate of methane with steam, because of the higher conversion rate. The present work indicates that the short-term performance of SOFCs with conventional Ni+YSZ anodes, in comparison with that under hydrogen fuel, is acceptable under internal reforming condition with the optimized fuel flow rate and S/C ratio.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.5
• /
• pp.397-403
• /
• 2009

The catalysis of carbon black was investigated for the production of hydrogen by the catalytic decomposition of propane-butane mixture gas in this study. The thermal and the catalytic decompositions of hydrocarbons were performed at the temperature range of 500 - $1100^{\circ}C$, respectively. The conversions of hydrocarbons and the mole traction of hydrogen increased with increasing the reaction temperature and the conversion of hydrocarbons in the catalytic decomposition process was approximately liked with that obtained by the thermal decomposition. However, the mole traction of hydrogen produced in the catalytic decomposition process was higher than that obtained from the thermal decomposition. Therefore, it was concluded that the catalysis for the decomposition of hydrocarbons is occurred over carbon black used as catalyst. The mole traction of hydrogen produced by the catalytic decomposition of hydrocarbons also increased with increasing the mole ratio of $C_3H_8/C_4H_{10}$ in propane and butane mixture gas at $700^{\circ}C$. Therefore, it was concluded that the catalytic decomposition of the high propane mixture gas is more effectively for the production of hydrogen.

• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.720-724
• /
• 2003

Aluminum nitride (AlN) powders were synthesized by using a mixture of an aluminum nitrate or sulfate salt and carbon (mole ratio of $Al^{3+}$ to carbon=L : 30). The AlN was obtained by calcining the mixture under a flow of nitrogen in the temperature range 1100-1$600^{\circ}C$ and then burning out the residual carbon. The process of conversion of the salt to AlN was monitored by XRD and $^{27}$ Al magic-angle spinning (MAS) NMR spectroscopy. The salt decomposed to ${\gamma}$-alumina and then converted to AlN without phase transition from ${\gamma}$-to-$\alpha$-alumina. $^{27}$ Al MAS NMR spectroscopy shows that the formation of AlN commenced at 110$0^{\circ}C$. AlN powders obtained from the sulfate salt were superior to those from the nitrate salt in terms of homogeneity and crystallinity. A very small amount of AlN whiskers was obtained by calcining a mixture of an aluminum sulfate salt and carbon at 115$0^{\circ}C$ for 40 h, and the growth of the whiskers is well explained by the particle-to-particle self-assembly mechanism.

• Korean Journal of Organic Agriculture
• /
• v.16 no.3
• /
• pp.287-298
• /
• 2008

This experiment was carried out to investigate the effect of different feed conditions on growth, cast production and conversion efficiency of organic matter to the earthworm. The experiment was tested on cow manure(CM) mixed with rice hulls (RH) or rice straw(RS). The mixture ratios were designed as one time, two times and three times of cow manure volume, respectively. The CM and RH mixtures resulted better on growth rate, reproductive efficiency and wormcast production than those for CM and RS mixtures. Especially on three times of RH mixture showed the highest growth characteristics compared to the other mixtures. Although both were between 20 and 34 on carbon and nitrogen ratio, the result inferred that the difference on the growth might have been caused by feeding conditions. On the mixtures of cow manure with rice hulls(CM+RH) was significantly higher on values on the conversion rate and conversion efficiency of organic matter to earthworm tissues than the mixtures of cow manure with rice straw(CM+RS). The most concerned point of the mixture of earthworm feed is that high contents of volatile solid and total carbon that increases in conversion efficiency of organic matter to earthworm tissues, and also causes the increase in growth rate and reproductive efficiency. The wormcast could be used as a valuable plant growth medium or soil conditioner for sustainable agriculture and it may be due to their high qualities of physico-chemical properties.

• 한국생물공학회:학술대회논문집
• /
• 2000.04a
• /
• pp.227-230
• /
• 2000

Batch cultivations of Anaerobiospirillum succiniciproducens have been systematically studied for the economical production of succinic acid from wood hydrolysate with corn steep liquor(CSL) as a nitrogen source. CSL was found to be an alternative complex nitrogen source for A. succiniciproducens when glucose and wood hydrolysate were used as carbon sources. Compared with polypeptone and/or yeast extract, CSL had similar effects on fermentation performance such as succinic acid yield and a ratio of succinic acid to acetic acid in the fermentation of wood hydrolysate as well as glucose. This means that succinic acid can be produced more economically from wood hydrolysate and CSL than relatively expensive carbon and nitrogen sources. Besides its low cost, the alternative medium served as a green technology for succinic acid production because it gives a net-zero effect on global warming.

• Journal of Korean Society of Forest Science
• /
• v.98 no.3
• /
• pp.324-330
• /
• 2009

The objective of this study is to estimate the carbon sequestration in forest stands using KOMPSAT-2 imagery. For estimating the amount of carbon sequestration, the stand biomass of forest was estimated with the total weight, which was the sum of individual tree weight. Individual tree volumes could be estimated by the crown width extracted from KOMPSAT-2 imagery. In particular, the carbon conversion index and the ratio of the $CO_2$ molecular weight to the C atomic weight, reported in the Intergovernmental Panel on Climate Change (IPCC) guideline, was used to convert the stand biomass into the amount of carbon sequestration. Thereafter, the KOMPSAT-2 imagery was classified with the segment based classification (SBC) method in order to quantify carbon sequestration by tree species. This approach, estimating the amount of carbon sequestration for certain species in stand, can be available to extend plot-based carbon sequestration to stand-based carbon sequestration.

• Applied Chemistry for Engineering
• /
• v.26 no.2
• /
• pp.205-209
• /
• 2015

CCU (Carbon Capture & Utilization) has a potential technology for the reduction and usage of carbon dioxide which is greenhouse gas emitting from a fossil fuel buring. To decompose the carbon dioxide, a three phase gliding arc plasma-catalytic reactor was designed and manufactured. Experiments of carbon dioxide reduction was performed by varying the gas flow rate with feeding the $CO_2$ only as well as the input power, the catalyst type and steam supply with respect to the injection of the mixture of $CO_2$ and $CH_4$. The $CO_2$ decomposition rate was 7.9% and the energy efficiency was $0.0013L/min{\cdot}W$ at a $CO_2$ flow rate of 12 L/min only. Carbon monoxide and oxygen was generated in accordance with the destruction of carbon dioxide. When the injection ratio of $CH_4/CO_2$ reached 1.29, the $CO_2$ destruction and $CH_4$ conversion rates were 37.8% and 56.6% respectively at a power supply of 0.76 kW. During the installation of $NiO/Al_2O_3$ catalyst bed, the $CO_2$ destruction and $CH_4$ conversion rates were 11.5% and 9.9% respectively. The steam supply parameter do not have any significant effects on the carbon dioxide decomposition.

• Journal of Microbiology and Biotechnology
• /
• v.25 no.3
• /
• pp.375-380
• /
• 2015

Recently, methane has attracted much attention as an alternative carbon feedstock since it is the major component of abundant shale and natural gas. In this work, we produced methanol from methane using whole cells of Methylosinus trichosporium OB3b as the biocatalyst. M. trichosporium OB3b was cultured on NMS medium with a supply of 7:3 air/methane ratio at 30℃. The optimal concentrations of various methanol dehydrogenase inhibitors such as potassium phosphate and EDTA were determined to be 100 and 0.5 mM, respectively, for an efficient production of methanol. Sodium formate (40 mM) as a reducing power source was added to enhance the conversion efficiency. A productivity of 49.0 mg/l·h, titer of 0.393 g methanol/l, and conversion of 73.8% (mol methanol/mol methane) were obtained under the optimized batch condition.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.412-415
• /
• 2013

Palladium on carbon powder was prepared using 1-hexyl-3-methylimidazolium tetrafluoroborate, one of room temperature ionic liquids. The synthesized particles were tested as a hexafluoropropylene hydrogenation catalyst. Moreover, the hydrogenation was performed under various reaction conditions to develop an optimum reaction process. The catalyst prepared by more than 3 wt% of palladium and the unity mole ratio of ionic liquid to palladium precursor showed higher catalytic activity. For reaction conditions, the complete hexafluoropropylene (HFP) conversion was achieved at these conditions; the volume flow ratio of hydrogen to HFP was higher than 1.25 and $GHSV_{HFP}$ was lower than 50000 mL/g-h.

• Korean Journal of Materials Research
• /
• v.30 no.12
• /
• pp.660-665
• /
• 2020

Silicon heterojunction solar cells can achieve high conversion efficiency with a simple structure. In this study, we investigate the passivation characteristics of VOx thin films as a hole-selective contact layer using ALD (atomic layer deposition). Passivation characteristics improve with iVoc (implied open-circuit voltage) of 662 mV and minority carrier lifetime of 73.9 µs after post-deposition annealing (PDA) at 100 ℃. The improved values are mainly attributed to a decrease in carbon during the VOx thin film process after PDA. However, once it is annealed at temperatures above 250 ℃ the properties are rapidly degraded. X-ray photoelectron spectroscopy is used to analyze the chemical states of the VOx thin film. As the annealing temperature increases, it shows more formation of SiOx at the interface increases. The ratio of V5+ to V4+, which is the oxidation states of vanadium oxide thin films, are 6:4 for both as-deposition and annealing at 100 ℃, and 5:5 for annealing at 300 ℃. The lower the carbon content of the ALD VOx film and the higher the V5+ ratio, the better the passivation characteristics.