• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2003년도 international symposium on advanced powder metallurgy
• /
• pp.41-42
• /
• 2003

Using a developed high-frequency induction heated combustion method. the simultaneous synthesis and densification of WC-xvol.%Co($0{\leq}x{\leq}20$) hard materials was accomplished using elemental powders of W, C and Co. A complete synthesis and densification of the materials was achieved in one step within a duration of 1min. The final relative densities of the composite were over 98.5% for all cases, under the applied pressure of 60 MPa and the induced current. The hardness of the composites decreases and the fracture toughness increases with increasing cobalt content. As the carbon to tungsten ration increases, the hardness increase, but the fracture toughness decreases. The maximum values for the fracture toughness and hardness are 15.1 $MPa{\cdot}m^{1/2}$(at 20vol.%Co, W:C=1:1), and 1928 $kg/mm^{2}$(at 5vol.%Co, W:C=1:1.3), respectively. Therefore we concluded that the HFIHCS method. which can produce WC-xvol.%Co within 1 minute in one step is superior to conventional ones.

• 한국응용과학기술학회지
• /
• 제2권2호
• /
• pp.47-53
• /
• 1985

Correlation among the wax-pigment composites which is base vehicles for the crepas was investigated in terms of fadeness. The base wax synthesized and pigments are compounded with petroleum lubricant and exposed under carbon arc individually. The yellowing phenomenon was appeared on the reference papers coated with the spindle oil which was then exposed. The papers were again extracted with distilled water and pH of them were ranged between 6.2-6.5. Color difference from Adam-Nickerson equation, ${\vartriangle}E$ of base wax is 0.15 and that of spindle oil are varied from 0.66 to 15.62. Since the main components of the petroleum lubricant are aromatic hydrocarbons which have absorptions characteric of UV ranging from 240 to 280 nm, fadeness characteristics of the composites are largely depend upon the change of molecular structure of spindle oil by absorbing UV. Thus the spindle oil having the following physical properties has the better resistance of fadness and is recommended to use in compounding the base wax-pigment composites: ${\cdot}$ main component: paraffinic hydrocarbon ${\cdot}$ pour point: below - $15^{\circ}C$ ${\cdot}$ UV absorption characteristics: ${\lambda}max.$ : 268-290nm ${\cdot}$ absorbancy: below 0.1(0.03ml of sample/50ml of $CHCl_3$)

• Elastomers and Composites
• /
• 제38권2호
• /
• pp.103-121
• /
• 2003

The application of powerful ultrasound to rubber recycling is a very recent field of study. An ultrasonic field creates high frequency extension-contraction stresses by acoustic cavitation. The breakdown of rubber network occurs primarily around pulsating cavities due to the highest level of strain produced by high-power ultrasound. Stronger reductions of cross-link density were observed at a higher pressure, indicating an important role of pressure during ultrasonic recycling. Visible bubbles were observed during ultrasonic treatment as a proof of acoustic cavitation. Shearing effect has a significant influence on improving the efficiency of ultrasonic treatment. After the ultrasonic treatment, the cross-link densities of NR/SBR blends were lower than those of NR and SBR due to the reduced degree of unsaturation and chemical reactions. Carbon black fillers increase the probability of bond scission during ultrasonic treatment, due to the restricted mobility. The mechanical properties of ground tire rubber (GRT)/HDPE blends were improved by ultrasonic treatment and dynamic revulcanization. Ultrasonic treatment of GRT in the presence of HDPE matrix was found to give better mechanical properties due to the chemical reactions between rubber and plastic phases.

• Composites Research
• /
• 제26권3호
• /
• pp.160-164
• /
• 2013

In this study, the effect of phosphoric acid (PA) as a fiber spinning aid on the strength increase of polyacrylonitrile (PAN) nano-fibers by using modified mechano-electrospinning technologies has been analyzed. The medium carbonization temperature of $800^{\circ}C$ has been selected for the future economic production of these new materials. The concentration of PAN in dimethyl sulfoxide (DMSO) was fixed as 5 wt%. The weight fraction of PA was selected as being 2%, 4%, 6%, and 8% in comparison to PAN. These solutions have been used to make the nanofibers. The mechano-electrospinning apparatus installed in KRICT was made by our own design. By using this apparatus the continous and highly aligned precursor nano-fibers have been obtained. The bundle of 50 well aligned nano diameter continuous fibers with the diametr of 10 microns with 6 wt% phosphoric acid for addition showed maximum mechanical properties of 1.6 GPa as tensile strength and 300 GPa as Young's modulus. The weight of final product can be increased 19%, which can improve the economical benefits for the application of these new materials.

• Journal of Electrochemical Science and Technology
• /
• 제2권3호
• /
• pp.152-156
• /
• 2011

A hybrid supercapacitor is fabricated using a composite material from $LiMn_2O_4$ (LMO) and activated carbon (AC) as the positive electrode and AC as the negative electrode to form the (LMO + AC)/AC system. Volume ratio (positive : negative) of electrodes is controlled to investigate of the power and energy balance. The (LMO + AC)/AC system shows better performances than the LMO/AC system. Especially, electrochemical impedance spectra, rate charge.discharge and cycle performance testing show that the (LMO + AC)/AC system have an outstanding electrochemical performance at volume ratios of (LMO + AC)/AC = 1 : 1.7 and 1 : 2. Electric double layer capacitor (EDLC) capacitance between AC of the positive electrode and AC of the negative electrode improves power density without loss of capacitance. Stable capacitance is achieved by lowering the positive electrode resistance and balancing the energy and power densities between the positive and negative electrodes by the addition of AC to the positive electrode at high current density.

• Journal of Electrochemical Science and Technology
• /
• 제1권1호
• /
• pp.25-30
• /
• 2010

This study demonstrated the synthesis of high-surface-area metal-free carbonaceous electrodes (CE) from anodic aluminum oxide (AAO) templates, and their application as supercapacitors. Multi-walled Carbon nanotubes (MWCNTs) were interwoven into a porous network sheet that was attached to one side of AAO template through a vacuum filtration of the homogeneously dispersed MWCNT toluene solution. Subsequently, the conducting polymer was electrochemically grown into the porous MWCNT network and nanochannels of AAO, leading to the formation of a carbonaceous metal-free film electrode with a high surface area in the given geometrical surface area. Typical conducting polymers such as polypyrrole (PPY) and poly(3,4-ethylenedioxythiophene) (PEDOT) were examined as model systems, and the resulting electrodes were investigated as supercapacitors (SCs). These SCs exhibited stable, high capacitances, with values as high as 554 F/g, 1.08 F/$cm^2$ for PPY and 237 F/g, 0.98 F/$cm^2$ for PEDOT, that were normalized by both the mass and geometric area.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.447-451
• /
• 2009

Continuous SiC fiber-reinforced SiC composites ($SiC_f$/SiC) were fabricated by electrophoretic deposition (EPD). Nine types of slurries with different powder contents, binder resin amounts and slurry pH were deposited on Tyranno$^{TM}$-SA fabrics by EPD at 135 V for ten minutes to determine the optimal conditions. Further EPD using the optimum slurry conditions was performed on fabrics with four different pyrolitic carbon (PyC) thicknesses. The density of the hot-pressed composites decreased with increasing PyC thickness due to the difficulty of infiltrating the slurry into the narrow gaps between the fibers. On the other hand, the mechanical strength increased with increasing PyC thickness despite the decrease in density, which was explained by the enhanced crack deflection with increasing PyC thickness. The $SiC_f$/SiC composites showed the highest density and flexural strength of 94% and 342 MPa, respectively, showing EPD as a feasible method for dense $SiC_f$/SiC fabrication.

• Steel and Composite Structures
• /
• 제20권6호
• /
• pp.1275-1303
• /
• 2016

Steel plates and carbon-fiber-reinforced polymer (CFRP) laminates or plates bonded to concrete substrates have been widely used for concrete strengthening. However, this technique cause plate debonding, which makes the strengthening system inefficient. The main objective of this study is to enhance the bond strength of externally bonded steel plates and CFRP laminates to the concrete surface by proposing new embedded adhesive and steel connectors. The effects of these new embedded connectors were investigated through the tests on 36 prism specimens. Parameters such as interfacial shear stress, fracture energy and the maximum strains in plates were also determined in this study and compared with the maximum value of debonding stresses using a relevant failure criterion by means of pullout test. The study indicates that the interfacial bond strength between the externally bonded plates and concrete can be increased remarkably by using these connectors. The investigation verifies that steel connectors increase the shear bond strength by 48% compared to 38% for the adhesive connectors. Thus, steel connectors are more effective than adhesive connectors in increasing shear bond strength. Results also show that the use of double connectors significantly increases interfacial shear stress and decrease debonding failure. Finally, a new proposed formula is modified to predict the maximum bond strength of steel plates and CFRP laminates adhesively glued to concrete in the presence of the embedded connectors.

• Structural Engineering and Mechanics
• /
• 제40권1호
• /
• pp.105-120
• /
• 2011

The strengthening and rehabilitation of reinforced concrete structures with externally bonded carbon fibre reinforced polymer (FRP) laminates has shown excellent performance and, as a result, this technology is rapidly replacing steel plate bonding techniques. This paper addresses this issue, and presents results deals with the influence of external bonded CFRP-reinforcement on the time-dependent behavior of reinforced concrete beams. A total of eight reinforced concrete beams with cracked and un-cracked section, with and without externally bonded CFRP laminates, were investigated for their creep and shrinkage behavior. All the beams considered in this paper were simply supported and subjected to a uniform sustained loading for the period of six months. The main parameters of this study are two types of sustained load and different degrees of strengthening scheme for both cracked and un-cracked sections of beams. Both analytical and experimental work has been carried out on strengthened beams to investigate the cracking and deflection performance. The applied sustained load was 56% and 38% of the ultimate static capacities of the un-strengthened beams for cracked and un-cracked section respectively. The analytical values based on effective modulus method (EMM) are compared to the experimental results and it is found that the analytical values are in general give conservative estimates of the experimental results. It was concluded that the attachment of CFRP composite laminates has a positive influence on the long term performance of strengthened beams.

• Steel and Composite Structures
• /
• 제22권3호
• /
• pp.691-712
• /
• 2016

In this editorial, buckling analytical investigation of the nanocomposite plate with square cut out reinforced by carbon nanotubes (CNTs) surrounded by Pasternak foundation is considered. The plate is presumed has square cut out in center and resting on Pasternak foundation. CNTs are used as amplifier in plate for diverse distribution, such as uniform distribution (UD) and three patterns of functionally graded (FG) distribution types of CNTs (FG-X, FG-A and FG-O). Moreover, the effective mechanical properties of nanocomposite plate are calculated from the rule of mixture. Domain decomposition method and orthogonal polynomials are applied in order to define the shape function of nanocomposite plate with square cut out. Finally, Rayleigh-Ritz energy method is used to obtain critical buckling load of system. A detailed parametric study is conducted to explicit the effects of the dimensions of plate, length of square cut out, different distribution of CNTs, elastic medium and volume fraction of CNTs. It is found from results that increase the dimensions of plate and length of square cut out have negative impact on buckling behavior of system but considering CNTs in plate has positive influence.