• Carbon letters
• /
• v.1 no.2
• /
• pp.60-63
• /
• 2000

In this work, the carbon fibers-reinforced carbon matrix composites made with different carbon char yields of phenolic resin matrix have been characterized by mechanical flexural tests for acoustic emission properties. The composites had been fabricated in the form of two-dimensional polyacrylonitrile based carbon fibers during the carbonization process. It was found that the composites made with the carbon char yield-rich of resin matrix result in better mechanical interfacial properties, i.e., the interlaminar shear strength (ILSS) of the composites. The data obtained from the acoustic emission monitored appeared to show that the composites made with carbon char yield-rich were also more ductile. From the acoustic emission results, the primary composite failure was largely depended on the debonding at interfaces between fibers and matrix. The interlaminar shear strengths of the composites were correlated with the acoustic emission results.

• Carbon letters
• /
• v.14 no.1
• /
• pp.34-39
• /
• 2013

Acrylonitrile (AN)-acrylamide (AM) copolymers were prepared by nitric acidic hydrolysis of homopolyacrylonitrile. The acrylamino group increased as a function of hydrolysis time, while crystallinity decreased. Differential scanning calorimetry and a thermal gravimetric analysis indicated that the acylamino introduced by acidic hydrolysis effectively enhanced the cyclization reaction at low temperature due to the change of the cyclization reaction mechanism. Char-yield of AN-AM copolymers also gradually increased with increasing hydrolysis time. The maximum char-yield was 49.48% when hydrolized at $23^{\circ}C$ in 65% nitric acid solution for 18 h, which was 30% higher than that of non-acidic hydrolysis of homopolyacrylonitrile. Simulation of the practical process also showed an increase of char yields, where the char yields were 55.43% and 62.60% for homopolyacrylonitrile and copolyacrylonitrile, respectively, with a hydrolysis time of 13 h.

• Elastomers and Composites
• /
• v.57 no.1
• /
• pp.9-12
• /
• 2022

Herein, a facile approach for the development of effective and low-cost carbon precursors from acrylonitrile-butadiene-styrene (ABS) rubber is reported. ABS rubber with a negligible char yield can be converted into an excellent carbon precursor with approximately 54% char yield under a nitrogen atmosphere at 800℃ by simple iodine doping and subsequent heating at 110℃ under an inert atmosphere. The enhanced char yield is attributed to the improved intermolecular interactions between the ABS chains caused by the formation of covalent bonds between the butadiene segments, along with the newly developed charge-charge interactions and other indiscriminate radical-radical couplings. The charges and radicals involved in these interactions are also generated by iodine doping. We believe that this study will be useful for the development of low-cost carbon precursors.

• Carbon letters
• /
• v.26
• /
• pp.66-73
• /
• 2018

We assessed the effects of combining bio-char with straw residue mulching on the loss of soil soluble nutrients and citrus yield in sloping land. The two-year study showed that straw residue mulching (ST) and bio-char application combined with straw residue (ST+BC) can significantly reduce soil soluble nutrient loss when compared with the control treatment (CK). The comparative volume of the soil surface runoff after each of the treatments was as follows: CK > ST > ST + BC. Compared with the CK, the runoff volume of the ST was reduced by 13.6 % and 8.5 % in 2014 and 2015, respectively. Compared with the CK, combining bio-char with the ST application reduced the loss of soluble nitrogen and improved the soil total nitrogen content reaching a significant level in 2015. It dramatically increased the soil organic matter content over the two year period (36.3% in 2014, 50.6% in 2015) as well as the carbon/nitrogen ratio (C/N) (16.6% in 2014 and 39.3% in 2015). Straw mulching combined with bio-char showed a trend for increasing the citrus yield.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.87-90
• /
• 2006

The experimental study has been done for two kinds of pelletized RDFs to Investigate the carbonization effect to the chlorine concentrations, the heating value and the yield of Produced char in variable conditions of the carbonizing temperature and reaction time. One(RDF-1) is made of 100% wasted plastics and the other(RDF-2) is made of 60% wasted paper with 40% wasted plastics. The screw type carbonizer heated Indirectly by oil burner was used for the experiment and RDF feeding rate was 3kg/hr. The carbonizing temperature was 300, 350 400 and $45^{\circ}C$ and the reaction tine was 5, 10 and 15 minutes respectively. As the increase of carbonizing reaction time and temperature, the chlorine reduction rate was increased and oppositely the yield of char was decreased At the temperature of $400^{\circ}C$ and reaction time of 10 minutes the chlorine reduction rate was 60% and the char yield rate was 80% for the RDF-1 and those of RDF-2 were 80% and 75%, respectively. Additional activation experiment to the char produced from RDF-2 was done in the activation reactor by hot steam supply. As the increase of activation time the iodine number was increased. At the activation time of 20 minutes the iodine number was 552mg/g and the yield of activated carbon was 16%.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.5
• /
• pp.45-52
• /
• 2014

Torrefaction and hydrothermal carbonization (HTC) are productive methods to reclaim energy from lignocellulosic biomass. The hydrophobic, homogenized, energy dense and carbon rich solid fuel can be obtain from torrefaction and hydrothermal carbonization. Dead leaves were carbonized in a stainless steel reactor of volume 200 ml with torrefaction ($250-270^{\circ}C$) for 120 minutes and hydrothermal carbonization ($200-250^{\circ}C$) for 30 minutes, with mass yield solid fuel ranging from 57-70% and energy content from 16.81MJ/kg to 22.01 MJ/kg compare to the biomass. The char produced from torrefaction process possess high energy content than hydrothermal carbonization. The highest energy yield of 89.96% was obtained by torrefaction at $250^{\circ}C$. The energy densification ratio fluctuated in between 1.15 to 1.30. On the basis of pore size distribution of the chars, the definition of the International Union of Pure and Applied Chemistry (IUPAC) was used as a classification standard. The pore diameter was ranging within 11.09-19 nm which play important role in water holding capacity in soil. Larger pores can hold water and provide passage for small pores. Therefore, it can be concluded that high pore size char can be obtained my HTC process and high energy content char of 22.01 MJ/Kg with 34.04% increase in energy can be obtain by torrefaction process.

• Carbon letters
• /
• v.28
• /
• pp.66-71
• /
• 2018

To improve the flame retardant performance of cellulose fibers, fluorine functional groups were introduced under various controlled fluorination conditions. The properties of the fluorinated cellulose fibers were analyzed by X-ray photoelectron spectroscopy and a thermogravimetric analysis. The fluorine functional group content in the fluorinated cellulose fibers increased with an increase in the fluorination temperature. However, the fluorination reaction increased the char yield and decreased the rate of degradation of the cellulose fibers by introducing donors, enabling the formation of a thick and compact char layer. Therefore, the flame retardant properties of cellulose fibers were improved following the fluorination treatment.

• Journal of Energy Engineering
• /
• v.13 no.2
• /
• pp.166-172
• /
• 2004

The activated carbon was produced from Sancheong bamboo by steam and carbon dioxide gas activation methods. The carbonization of raw material was conducted at 90$0^{\circ}C$ and gas activation reactions were conducted with respect to various conditions. -activation temperature 750-90$0^{\circ}C$, the flow rate of steam 0.5-2g-$H_2O$/g-char$.$hr, the flow rate of carbon dioxide 5-30$m\ell$-$CO_2$/g-char-min and activation time 1-5 hr. The prepared activated carbons were measured yield, the adsorption capacity of iodine and methylene blue, BET specific surface area and pore size distribution. The adsorption capacity of iodine (680.5-1526.1 mg/g) and methylene blue (18.3-221.5 mg/g) increased with creasing activation temperature and activation time. The adsorption capacity of iodine and methylene blue increased with the activation gas quantity in the range of 0.5-1.5g-$H_2O$/g-charㆍhr, 5-18.9$m\ell$-Co$_2$/g-charㆍmin. But those decreased over those range due to the pore shrinkage. The steam activation method was superior in efficiency to carbon dioxide activation method.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.5
• /
• pp.686-698
• /
• 2011

Mathematical models for char-slag interaction and near-wall particle segregation developed by Montagnaro et. al. were applied to predict various aspects of coal gasification in an up-flow entrained gasifier of commercial scale. For this purpose, some computer simulations were performed using gPROMS as the numerical solver. Typical design parameters and operating conditions of the commercial gasifiers were used as input values for the simulation. Development of a densely dispersed phase of solid carbon was found to have a critical effect on both carbon conversion and ash flow behavior. In general, such a slow-moving phase was turned out to enhance carbon conversion by lengthening the residence time of char or soot particles. Furthermore, it was also found that guiding the transfer of char or soot into the closer part of the wall to coal burner is favorable in terms of gasification efficiency and vitrified ash collection. Finally, to a certain degree densely dispersed phase of carbon showed an yield-enhancing effect of syngas.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.36-42
• /
• 2019

In this study, the pre-treatment of lyocell fabrics was performed using phosphoric acid (PA) as a phosphorus flame retardant and melamine resin (MR) as a cross-linking agent to fabricate carbon fabrics using lyocell fibers. The physical and chemical changes were investigated by thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), X-ray diffractometry (XRD) and weight analysis. We confirmed that the weight yield of the carbon fabrics compared to the untreated fabrics increased by 14.7%, and width and length yield of the fabrics increased by 15% and 15.5%, respectively. This may be due to the effect of promoting the dehydration reaction of cellulose, forming char on the fiber surface, which induces a crosslinking reaction in the cellulose molecule and stabilizes the structure upon pyrolysis.