• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.242-248
• /
• 2000

This paper has focused on the optimization of the cutting parameters for turning operation based on the Taguchi method. Four cutting parameters, namely, cutting speed, feed, depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using the signal-to-noise (S/N) ratio, analysis of variance (ANOVA). The experiments have been peformed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.227-230
• /
• 2002

New polishing technique for small parts has been tried out using the principle of particle electromechanics. Common fine abrasives such as alumina, diamond, silicon carbide are dielectric materials which are polarized under an electric field, and a non-uniform electric field makes abrasive particles translate along the field line. Using this principle, We make abrasive particles aggregate in the vicinity of the micro tool which is fir the surface finishing of a small part without contact with it. The behavior of particles is optically measured, and the machined depth of glass is examined.

• 한국공작기계학회논문집
• /
• 제12권5호
• /
• pp.59-66
• /
• 2003

This study suggests the new ultraprecision finishing techniques for micro die and mold parts using magnetic field-assisted polishing. Conventional magnetic abrasives have several disadvantages, which are missing of abrasive particle and inequal mixture between magnetic particle and abrasive particle. Therefore, bonded magnetic abrasive particles are fabricated by several method. For example, plasma melting and direct bonding. Carbonyl iron powder is used as magnetic particle there silicon carbide and alumina are abrasive particles. Developed magnetic abrasives are analyzed using SEM. Feasibility of magnetic abrasive and polishing performance of this magnetic abrasive particles also have been investigated. After polishing, surface roughness of workpiece is reduced from 85.4 ㎚ Ra to 9 ㎚ RA.

• 한국기계연구소 소보
• /
• 통권20호
• /
• pp.79-87
• /
• 1990

Advanced ceramics have some excellent properties as the material for the mechanical component. It is, however, very difficult to grind ceramics with high efficiency because of their high strength, hardness and brittleness. Thus it is required also by a strong boom of demands for development of Machinable ceramics with high machinability in the most of industries. In present research, experiments are carried out to compare the machinability of sample Machinable ceramics. A $\ell$N(Aluminum Nitride) with additives of BN(Boron Nitride), yttrium. CaO are turned with cut-off tool type tungsten carbide bite using conventional turning machine.

• 한국안전학회지
• /
• 제23권6호
• /
• pp.1-6
• /
• 2008

Machine operator and quality are affected by chip during cutting process to product machine parts. This paper presents a study of the influence of cutting conditions on the surface roughness obtained by turning using Taguchi method for safety of turning operator. In the machining of titanium alloy, high cutting temperature and strong chemical affinity between the tool and the work material are generated because of its low thermal conductivity and chemical reactivity. Therefore titanium alloys are known as difficult-to materials. An orthogonal array, the signal-to-noise ratio, the analysis of variance are employed to investigate the cutting characteristics of implant material bars using tungsten carbide cutting tools of throwaway type. Also Experimental results by orthogonal array are compared with optimal condition to evaluate advanced reliability. Required simulations and experiments are performed, and the results are investigated.

• Tribology and Lubricants
• /
• 제4권2호
• /
• pp.44-51
• /
• 1988

Titanium carbide(TiC), Titanium nitride(TiN), and Titanium carbonnitride(Ti(C,N)) films were deposited on $Si_3N_4$-TiC composite cutting tools by chemical vapor deposition(CVD) using $TiCl_4-CH_4-H_2$, $TiCl_4-N_2-H_2$, and $TiCl_4-CH_4-N_2-H_2$ gas mixtures, respectively. The experimental results indicate that TiC coatings compared with TiN coatings on $Si_3N_4$ -TiC ceramic have an improved microstructural property, good thermal shock resistance, and good interfacial bonding. However TiN coatings compared with TiC coatings have a low friction coefficient with steel and good chemical stability. It is found by cutting test that coated insert compared with $Si_3N_4$-TiC ceramic have a superior flank and crater wear resistance. And multilayer coating compared with monolayer coating shows a improved wear resistance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.585-588
• /
• 2005

The dissolution characteristic of metal shows the different tendency according to the applied electrical potential, the kind of electrolyte and pH value, etc. In the micro electrochemical machining (ECM), unfavorable oxide/passive layer formation and overall corrosion of electrodes must be prevented. The anodic polarization curve of nickel has distinct three dissolution regions, i.e. two active regions and the transpassive dissolution region. In this paper, the stable electrode potentials of workpiece and tool were determined in sulfuric acid and hydrochloric acid solution, respectively. In each solution, different machining property was shown and possible electrochemical reactions were discussed. On the basis of this experiment, the methodology to obtain the proper electrode potential was suggested.

• 한국정밀공학회지
• /
• 제8권2호
• /
• pp.36-46
• /
• 1991

This study was carried out to investigate the characteristic of dynamic component in drilling. Materials used were carbon steel, brass and cast iron, and the drills used were high speed steel drill and cemented carbide. The cutting resistance generated in drilling was detected with the aid of piez0-electric tool dynamometer which has an excellent frequency response, and then the magnitude and shape of dynamic component and its frequency component as well were analyuzed. After a thorough study of interrelationship, the obtained results are as follows; 1) The shape of torque and thrust of the early drilling are different. 2) The shapes of dynamic component can be classified into four kinds. 3) Torque is related to frequency more closely than thrust. 4) As cutting speed increased, dynamic component increased. 5) Chipping took place continuously, and its size decreased as cutting proceeded.

• 한국표면공학회지
• /
• 제17권1호
• /
• pp.7-13
• /
• 1984

Carburizing of a 12%Cr steel containing 0.6%Si was performed at 950$^{\circ}C$ for various times, and the microstructure, hardness and the water characteristics of the carburized chromium steel were examined. The results obtained in this study are as follows: 1. Carbide-dispersed layer (CD layer) with fine dispersion of $Cr_7C_3$ in martensite matrix was formed by carburizing. The radius and amount of the carbides in the surface region of CD layer were about 0.3${\mu}m$ and 35% by volume, respectively. 2. Chromium steel carburized and quench-tempered showed better wear resistance and hardness than ordinary high chromium tool steel. It is concluded from these results that fine dispered carbides are very effective in improving wear resistance and hardness.

• 한국기계기술학회지
• /
• 제20권6호
• /
• pp.941-946
• /
• 2018

Currently, due to the development of technology, the industry is proceeding with the development of advanced materials with high performance such as light weight, heat resistance and electric conductivity. Carbon Fiber Reinforced Plastics (CFRP) is an excellent material with high heat resistance, high strength and thermal shock resistance. In order to obtain excellent hole shape in CFRP drilling, we compared the modified drill shape and the conventional carbide drill. On the other hand, we determine the proper helix angle by observing the CFRP surface according to the helix angle at the trimming of the end mill proceeding after the hole machining.