• 대한기계학회논문집A
• /
• 제30권9호
• /
• pp.1154-1159
• /
• 2006

In this paper, time-frequency analysis and multi-dimensional spectral analysis methods are applied to source identification and diagnostic of non-stationary sound vibration signals. By checking the coherences for concerned time, this simulation is very well coincident to expected results. The proposed method analyzes the signal instantaneously in both time and frequency domains. The MDSA (Multiple Dimensional Spectral Analysis) analyzes the signal in the plane of instantaneous time and instantaneous frequency at the same time. And it was verified by using the 1500cc passenger car which is accelerated from 70Hz to 95Hz in 4 seconds, the proposed method is effective in determining the vehicle diagnostic problems.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1346-1353
• /
• 2007

2003년 대구 지하철(중앙역) 화재 사건 당시의 화재 유동 및 승객 피난 시뮬레이션을 수행하였다. 화재 발생 첫 지점은 중앙역 지하 3층 객차 내부이며, 지하 3층과 지하 2층의 화재 및 연기 유동을 FLUENT 6.2를 이용하여 수치해석 하였다. 화재 객차 및 승강장에서의 이산화탄소 및 온도분포를 예측하였으며, 수치해석을 통하여 구해진 data는 승객 피난 시뮬레이션(EXODUS)의 입력 인자로 사용되었다. 수치해석에서 가장 높은 온도는 1500K로 조사되었다. EXODUS를 이용하여 지하 3층에서 지하1층까지 승객 피난 시뮬레이션이 수행되었으며, 총 피난 승객은 1000명으로 가정하였다. 이중 640명은 객차 내부에, 360명은 승강장에 존재하는 것으로 하고 계산을 수행하였다. 피난 시뮬레이션 결과 135명이 사망하였으며 이는 대구 화재 사고결과에 비교적 근접하는 수치이다. 또한 평균 피난 시간은 10분 19초로 조사가 되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1095-1098
• /
• 2005

Most electronic chassis control systems until today have been designed with optimization on its own performance. However, According to the increase of the interest regarding a vehicle safety and development of information technique, the integration technique of current chassis systems is being emphasized. Each enterprise proposed it with name of GCC(Global Chassis Control) or UCC(Unified Chassis Control). This study realizes control algorithm of suspension and brake by using the vehicle model of low degree of freedom as the primary stage of realization of integrated chassis control system. The proposed algorithm build the simulation environment connected to the CarSim having full vehicle model of 27 degree of freedom for raising the thrust of results

• Journal of Power Electronics
• /
• 제13권4호
• /
• pp.536-545
• /
• 2013

In this study, an integrated motor control algorithm for an in-wheel electric vehicle is suggested. It consists of slip control that controls the in-wheel motor torque using the road friction coefficient and slip ratio; yaw rate control that controls the in-wheel motor torque according to the road friction coefficient and the yaw rate error; and velocity control that controls the vehicle velocity by a weight factor based on the road friction coefficient and the yaw rate error. A co-simulator was developed, which combined the vehicle performance simulator based on MATLAB/Simulink and the vehicle model of CarSim. Based on the co-simulator, a human-in-the-loop simulation environment was constructed, in which a driver can directly control the steering wheel, the accelerator pedal, and the brake pedal in real time. The performance of the integrated motor control algorithm for the in-wheel electric vehicle was evaluated through human-in-the-loop simulations.

• 제어로봇시스템학회논문지
• /
• 제21권7호
• /
• pp.595-601
• /
• 2015

This paper presents an unified chassis control with electronic stability control (ESC) and active front steering (AFS) under lateral force constraint on AFS. When generating the control yaw moment, an optimization problem is formulated in order to determine the tire forces, generated by ESC and AFS. With Karush-Kuhn-Tucker optimality condition, the optimum tire forces can be algebraically calculated. On low friction road, the lateral force in front wheels is easily saturation. When saturated, AFS cannot generate the required control yaw moment. To cope with this problem, new constraint on the lateral tire force is added into the original optimization problem. To check the effectiveness of the propose method, simulation is performed on the vehicle simulation package, CarSim.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.20-28
• /
• 2014

This paper presents static output feedback LQ and $H_{\infty}$ controllers for rollover prevention. Linear quadratic static output feedback controllers have been proposed for rollover prevention in such a way to minimize the lateral acceleration and the roll angle. Rollover prevention capability can be enhanced if $H_{\infty}$ controller is designed. To avoid full-state measurement for feedback requirement or sensitiveness of an observer to nonlinear model error, static output feedback is adopted. To design static output feedback controllers, Kosut's method is adopted because it is simple to calculate. Differential braking and active anti-roll bar are adopted as actuators that generate yaw and roll moments, respectively. The proposed method is shown to be effective in preventing rollover through the simulations on nonlinear multi-body dynamic simulation software, CarSim.

• 자동차안전학회지
• /
• 제5권1호
• /
• pp.56-61
• /
• 2013

This paper presents a development of the Advanced Emergency Braking (AEB) Algorithm for passenger vehicles. The AEB is the system to slow the vehicle and mitigate the severity of an impact when a rear end collision probability is increased. To mitigate a rear end collision, the AEB comprises of a millimeter wave radar sensor, CCD camera and vehicle parameters of which are processed to judge the likelihood of a collision occurring. The main controller of the AEB algorithm is composed of the two control stage: upper and lower level controller. By using the collected obstacle information, the upper level controller of the main controller decides the control mode based not only on parametric division, but also on physical collision capability. The lower level controller determines warning level and braking level to maintain the longitudinal safety. To decide the braking level, Last Ponit To Brake and Steer (LPTB/LPTS) are compared with current driving statues. To demonstrate the control performance of the proposed AEBS algorithm's, closed-loop simulation of the AEBS was conducted by using the Matlab simlink and CarSim software.

• 자동차안전학회지
• /
• 제11권2호
• /
• pp.17-22
• /
• 2019

This paper describes the tracking algorithm performance evaluation for autonomous vehicle using a safety envelope based path. As the level of autonomous vehicle technologies evolves along with the development of relevant supporting modules including sensors, more advanced methodologies for path generation and tracking are needed. A safety envelope zone, designated as the obstacle free regions between the roadway edges, would be introduced and refined for further application with more detailed specifications. In this paper, the performance of the path tracking algorithm based on the generated path would be evaluated under safety envelop environment. In this process, static obstacle map for safety envelope was created using Lidar based vehicle information such as current vehicle location, speed and yaw rate that were collected under various driving setups at Seoul National University roadways. A level of safety was evaluated through CarSim simulation based on paths generated with two different references: a safety envelope based path and a GPS data based one. A better performance was observed for tracking with the safety envelop based path than that with the GPS based one.

• 한국정밀공학회지
• /
• 제30권1호
• /
• pp.85-95
• /
• 2013

As the conventional hydraulic power steering system in the passenger vehicles is being rapidly replaced by EPS (Electric Power Steering) system, performance evaluation of the EPS system has become an important issue in the automotive industries. But the evaluation process takes significant expertise since steering conditions in the test protocols must be implemented with high accuracy. EPS HILS (Hardware-In the-Loop Simulation) system is developed together with robot steering system in this study. Main components of EPS HILS system include: C-EPS hardware, CarSim vehicle model, and road reaction force generation system powered by servo motor. The robot steering system, operated by another servo motor, was combined with EPS HILS system to substitute for steering efforts of human driver. The road reaction force generation system and the robot steering system were carefully validated by using the data obtained from vehicle tests. An on-center handling test was conducted by using EPS HILS system combined with the robot steering system. In the result of this study, robot-steered EPS HILS system developed with its high reliability and no need of skilled driver's, can be widely adopted to evaluate any performance of EPS system.

• 한국정보통신학회논문지
• /
• 제21권10호
• /
• pp.1879-1885
• /
• 2017

본 논문에서는 시간에 따라 방향 속도와 위치가 변하는 무인자동차의 궤적 추적 제어시스템에 대해 논한다. 무인자동차는 운전자의 도움이 없어도 스스로 주위환경을 인식하여 지정된 도로를 주행할 수 있는 자동차로 올바른 주행을 위해 고려해야 할 변수가 다양하다. 무인자동차의 궤적 추적 시스템에서 인식한 정보는 이산적인 값을 가지므로 센스 간의 간격으로 인하여 비연속성 및 비선형성을 가지고 있다. 이로 인하여 목표 궤적을 정확하게 추적하는 것 어렵다. 본 논문은 차량의 운동학 모델링을 통하여 선형오차, 제약 조건, 제어 목표함수의 세 가지 조건을 갖는 무인자동차 궤적 추적시스템을 제안한다. 제안된 궤적 추적시스템을 기반으로 동적 시뮬레이션 소프트웨어-카심(Dynamic Simulation Software-CarSim)의 결합시뮬레이션을 통해 시스템의 성능을 평가하였고, 그 결과로 더욱 정밀하게 목표 궤적을 추적할 수 있음을 확인하였다.