• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1833-1840
• /
• 1993

An efficient vibration analysis method, Component Mode Synthesis(CMS), for an exhaust system with bellows is presented. Analyses are performed for two types of bellows, where characteristics of vibration modes affecting idle shake and interior noise of a vehicle are examined. Also analyzed are the contributions of an exhaust and engine mounting system to the idle shake and interios noise. Comparison between the analysis and test is in good agreement, hence the CMS method is shown to be efficient and valid.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.153-160
• /
• 2001

A general procedure for the design sensitivity analysis of structural dynamic problems has been presented in frame of the FRF-based substructuring formulation. For a system response function, the proposed method gives a parametric design sensitivity formula in terms of the partial derivatives of the connection element properties and the transfer matrix of the subsystems. The derived design sensitivity formula is applied to an engine mount system. An interior noise problem in the passenger car is analyzed using the FRF-based substructuring method and the proposed formulation is adopted to study the response variations with respect to the dynamic characteristics of the engine mounts and the bushes. To obtain the FRFs, a finite element model is built for the engine mount structures, and test data is used for the trimmed body including cabin cavity. The comparison of sensitivities derived by the proposed method and the finite difference method shows that the proposed method is efficient and accurate. The proposed sensitivity analysis method indicates effectively the most sensitive location to the interior noise among the engine mounts and the bushes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.180-185
• /
• 2005

Gear whine noise of the axle and transmission is getting more important for reduction of vehicle noise, because major noise of vehicle was reduced. Therefore, in this paper, axle noise and vibration is measured, then the modal analysis and running modal analysis is applied for identification of axle gear whine noise. And To reduce axle noise, Various structural modifications are performed by using FEM and BEM techniques.

• The Journal of the Acoustical Society of Korea
• /
• 제22권2E호
• /
• pp.87-92
• /
• 2003

In this paper, a new speech enhancement method using level adapted wavelet packet is presented. First, we propose a level adapted wavelet packet to alleviate a drawback of the conventional node adapted one in noisy environment. Next, we suggest an adaptive noise estimation method at each node on level adapted wavelet packet tree. Then, for more accurate noise component subtraction, we propose a new estimation method of spectral subtraction weight. Finally, we present a modified spectral subtraction method. The proposed method is evaluated on various noise conditions: speech babble noise, F-l6 cockpit noise, factory noise, pink noise, and Volvo car interior noise. For an objective evaluation, the SNR test was performed. Also, spectrogram test and a very simple listening test as a subjective evaluation were performed.

• 한국소음진동공학회논문집
• /
• 제14권9호
• /
• pp.884-890
• /
• 2004

In this paper, an index for the evaluation of vehicle intake booming noise is developed through a correlation analysis of objective measurement data and subjective evaluation data. First, intake orifice noise is measured at the wide-open test condition. And then, acoustic transfer function between intake orifice noise and interior noise at the steady state condition is estimated. Simultaneously, subjective evaluation was carried out with a ten-scale score by 8 engineers. Next, the correlation analysis between the psycho-acoustic parameters derived from the measured data and the subjective evaluation is performed. The most critical factor was determined and the corresponding index for the intake booming noise is obtained from the multiple factor regression method. At last, the effectiveness of the proposed index is validated.

• 한국소음진동공학회논문집
• /
• 제15권8호
• /
• pp.939-944
• /
• 2005

In this paper, a sound quality index for the evaluation of the vehicle intake noise was developed through a correlation analysis of the objective measurement and the subjective evaluation. First, intake orifice noise was measured at the wide-open throttle sweep condition. And then, the acoustic transfer function between intake orifice noise and interior noise was measured. Simultaneously, subjective evaluation was carried out with a 10-scale score by 8 special engineers. The correlation analysis between the psychoacoustic parameters derived from the measurement and the subjective evaluation was performed. The most critical factor was determined and the corresponding sound quality index for intake noise was obtained from the multiple factor regression analysis method. Finally, the effectiveness of the proposed index was validated.

• 소음진동
• /
• 제9권1호
• /
• pp.97-102
• /
• 1999

Structure-borne noise is an important aspect to consider during the design and development of a vehicle. In this work. it was desired to identify the primary paths associated with structure-borne noise generated from the engine and front suspension. An experimental source-path-receiver model was used to characterize the system. A variety of primary sources such as engine. tires or exhaust system generate vibrations of the inner surfaces of the passenger compartment of a vehicle which subsequently radiate noise. The source was characterized by the force acting at the engine-to-body interface. and the path was characterized by pressure over force FRF's. The excitation forces were indirectly determined using dynamic stiffness of rubber mount or the system accelerance matrix. Through these analysis, path contribution diagram which is well expressed primary noise path is obtained.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.600-604
• /
• 2013

A CTBA(Coupled Torsion Beam Axle) is a general type for rear suspension of small/compact sedans. It connects left and right knuckles using torsion beam axle and trails rear wheels. Therefore, a CTBA performs a main role of ride & handing. But, a CTBA suspension has main bending mode around 120Hz and causes road booming noise in the interior of a car. Therefore, the mode control of a CTBA is very important for reducing road noise. In this paper, we optimized the shape of a CTBA to reduce road noise considering R&H performance, simultaneously. The vibration mechanism of CTBA was investigated using ODS(Operational Deflection Shape) and mode shape.

• 한국소음진동공학회논문집
• /
• 제26권2호
• /
• pp.195-202
• /
• 2016

In this study, a concept of active sound enrichment (ASE) control system was implemented and demonstrated for improving engine sound quality inside the cabin of a passenger car during acceleration. Unlike the active noise control cancels the noise for disturbance rejection, the ASE adds additional sound to the noise for tracking control. This approach requires a new algorithm to provide additional artificial sound to the original engine sound using active control strategy to achieve a target sound profile, which is predefined to satisfy required interior sound quality. The ASE algorithm was implemented in a digital controller dSPACE DS1401 and real-time control experiment was accomplished in an actual car. The ASE control results show that the actively enriched sound of each engine order against RPM tracks the target profiles precisely and quickly and improves the discontinuity, the level ratios and the sound pressure level of each engine order. Thus it is anticipated the ASE system can be applied for the improvement of the engine sound quality inside the cabin during acceleration.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.514-520
• /
• 2000

Numerical simulation is conducted to clarify the heat transfer and fluid flow characteristics of HVAC(Heating, Ventilating and Air-Conditioning) for Mugunghwa passenger car. The HVAC system is installed under the floor of carbody. This new HVAC system has a lot of merits in respect of the center of gravity of carbody, flow induced noise and reduction of condensation water etc. The standard k-epsilon turbulent model and SIMPLEC algorithm based on finite volume method are used to solve the physical HVAC model. To assure convergence, QUICK scheme for momentum equation and the first order upwind scheme for turbulent equations are used. From the results of simulation, the temperature and velocity magnitude are also distributed uniformly in the interior of car.