• Fire Science and Engineering
• /
• v.11 no.1
• /
• pp.47-54
• /
• 1997

Using high tensile steel plate makes the vehicle body stiffness lower even though it can lessen the fuel consume rate in application of weight reduction. The crack which happens arround vehicle window glass is brought about due to fatigue with low torsional stiffness. The paper presents a most suitable way to increase torsional stiffness using elasticity theory. Also the result of this study shows good agreement with FEM and experiments. We used a passenger car for calculation in this paper. Because we can apply the result of this study to fire engine as well as passenger car.

• Proceedings of the IEEK Conference
• /
• 2009.05a
• /
• pp.347-349
• /
• 2009

Air quality of indoor space environment is affected by various pollutants like as particles and chemical stuffs. The indoor air pollution affects directly the human respiration organs to cause consequently unpleasant mental status. The $CO_2$ concentration level is one of the harmful components of air pollutants. Major factor to increase the $CO_2$ concentration level is the people's breath amount in indoor. The car exhaust gas diffused from the around road also has strong affect on $CO_2$ concentration. There are some other reasons to affect the $CO_2$ concentration change, such as, real-time change of the population movement, closeness to the indoor air flow inlet window and changes in road car traffic amount. A remote monitoring system to measure environmental indoor air pollution concerning on the $CO_2$ concentration was studied and installed realized set-up model. Zigbee network configuration was applied for this system and the $CO_2$ concentration data were collected through USN network. A software program was developed to assure systematic analysis and to display real-time data on web pages. For the experimental test various condition was set up, like as, window opening, stopping air condition operation and adjusting fan heater work, etc. The analysis result showed the relation of various environmental conditions to $CO_2$ concentration changes. The causes to increase $CO_2$ concentration were experimentally defined as windows closing, the stopping air condition system, fan heater operation. To keep the $CO_2$ concentration under the legally required ppm level in public access indoor space, the developed remote measurement system will be usefully applied.

• Design Convergence Study
• /
• v.15 no.1
• /
• pp.135-150
• /
• 2016

Due to the development of communication technology and expansion of Intelligent Transport System (ITS), the car is changing from a simple mechanical device to second living space which has comprehensive convenience function and is evolved into the platform which is playing as an interface for this role. As the interface area to provide various information to the passenger is being expanded, the research importance about smart car based user experience is rising. This study has a research objective to propose the guidelines regarding the smart car user experience elements. In order to conduct this study, smart car user experience elements were defined as function, interaction, and surface and through the discussions of UX/UI experts, 8 representative techniques, 14 representative techniques, and 8 locations of the glass windows were specified for each element. Following, the smart car users' priorities of the experience elements, which were defined through targeting 100 drivers, were analyzed in the form of questionnaire survey. The analysis showed that the users' priorities in applying the main techniques were in the order of safety, distance, and sensibility. The priorities of the production method were in the order of voice recognition, touch, gesture, physical button, and eye tracking. Furthermore, regarding the glass window locations, users prioritized the front of the driver's seat to the back. According to the demographic analysis on gender, there were no significant differences except for two functions. Therefore this showed that the guidelines of male and female can be commonly applied. Through user requirement analysis about individual elements, this study provides the guides about the requirement in each element to be applied to commercialized product with priority.

• Journal of the Korea Safety Management & Science
• /
• v.15 no.2
• /
• pp.63-69
• /
• 2013

The purposes of this study are to survey stereotypes of control-display relationships for seven principal controls in passenger cars using the paper-pencil and hardware tests, and to examine stereotype strength of the paper-pencil test through comparing the stereotypes for the controls derived by the two methods. Ninety two and 60 college-aged students participated in the paper-pencil test and the real car simulation of the hardware test, respectively. There are dominant motion-directions for all controls in the paper-pencil test, while in the hardware test, there are dominant motion-directions for six controls including head light, high beam, door window, ignition key, door key and door lock controls. The stereotypes of motion-directions for six controls obtained by the paper-pencil test were the same as or similar to those by the hardware test. It was inferred from this that the congruence of the stereotypes by the two methods might be attributed to two simple motion-direction principles of 'clockwise for increase' and 'upward for increase.' Although it is known that the hardware test would be best for obtaining accurate stereotypes between controls and displays, this study implies that if the paper-pencil test is well designed, the paper-pencil test can produce the same results as the hardware test at low cost and without consuming time.

• Journal of KSNVE
• /
• v.3 no.4
• /
• pp.341-352
• /
• 1993

Although a frequency analysis by FFT algorithm has been widely used in the vibration community, this approach has somewhat limited features when an analysist want to see the details of frequency trends because FFT shows only energy contents along frequencies. So the concept of instantaneous frequency that represents the dominant frequency component at each time needs to be introduced. In this paper, to get the instantaneous frequency, two methods are used. Methods using Hilbert transform and evolutionary spectrum are those. One of the problems of estimating instantaneous frequency using Hilbert transform is that it is normally very sensitive to signal to noise ratio(SNR) because of the differentiation. Moving window is applied on the estimation of instantaneous frequency, and instantaneous frequency histogram are used to handle this problem and proved to be very effective. Computer simulations for various signals have been done to understand the characteristics of instantaneous frequency. The usefulness of signal analysis using instantaneous frequency was tested by three simple experiments, which were engine experiment, beam experiment, and car door experiment. The instantaneous frequency analysis is found to be a useful technique to analyze the signals that have time varying frequencies.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.167-173
• /
• 2005

Thermal regeneration means burning-off and cleaning-up the particulate matters piled up in DPF(diesel particulate filter), and it requires both high temperature $(550\~600^{\circ}C)$ and appropriate concentration of oxygen at DPF entrance. However, it is not easy to satisfy such conditions because of the low temperature window of the HSDI(high speed direct injection) diesel engine(approximately $200\~350^{\circ}C$ at cycle). Therefore, this study is focused on the method to raise temperature using the trade-off relation between temperature, oxygen concentration, and the influence of many parameters of common rail injection system including post injection. After performing an optimal mapping of the common rail parameters for regeneration mode, the actual cleaning process during regeneration mode is investigated and evaluated the availability of the regeneration mode mapping through regenerating soot trapped in the DPF.

• The Journal of the Korea Contents Association
• /
• v.14 no.4
• /
• pp.37-46
• /
• 2014

Industrialization and urbanization have led automobiles to transform into more than just modes of transportation; they have become daily necessities as well as extensions of living spaces where a variety of activities can be done and automotive applications of the latest information technology are accelerated. Though material abundance has increased in the modern society, the conflicts and the stress emerging from a social structure focused on competition have increased as well. Such lifestyles generate a need for personal space and media content for healing the body and the mind. This research explores the automotive application of video content with the goal of refreshing the minds of the passengers. To this end, previous studies have investigated the emotional effect of videos, focusing on the responses of diverse groups of adults (age group of 20 to 60) who frequently used automobiles, which had video displays installed in them. The results showed that watching video contents on a full window inside a car influenced the creation of positive feelings7 and emotional satisfaction. The research attempts to study the methods of providing video contents and the effects of watching them that could aid the emotional well-being of passengers, and presents the possibility of emotional satisfaction created by a convergence of cars and multimedia contents in the future.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.3B
• /
• pp.165-173
• /
• 2012

In this paper, we propose a random backoff scheme for Emergency Warning Messages (EWMs) in the vehicle-to-vehicle environment. The EWMs are disseminated from a vehicle that detects an emergency situation to other vehicles in a multi-hop fashion. Since the vehicle-to-vehicle communication based on IEEE 802.11 adapts CSMA/CA, the density of vehicles increase the probability of collisions between transmissions. Moreover, in the presence of background traffic, the EWM should have a higher priority than that of other messages in neighboring vehicles. To that end, we propose the Distant-Dependent Adaptive Backoff (DDAB) scheme, which set a different contention window for random backoff depending on the distance from the sender to the receiver. In the case when a vehicle is expected to located in the outskirts of the communication boundary, the proposed scheme makes the contention window size small in order to compete the background traffic transmission. Otherwise the contention window is set to a large number to reduce the collision possibility among the EWM transmissions. Via simulations, we show that the proposed scheme performs better than the previous schemes for EWM.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.466-471
• /
• 2014

The interior vehicle noise due to the exterior aerodynamic field is an important topic in the acoustic design of a car. The air flow detached from the A-pillar and impacting the side windows are of particular interest as they are located close to the driver / passenger and provides a lower insulation index than the trimmed car body parts. This paper presents a numerical analysis method for a simplified vehicle model. The internal air cavity including trim component are included in the simulation. The car body includes the windshield and two side windows. The body is made of aluminum and trimmed with porous layers. The methodology proposed in this paper relies on two steps: the first step involves the computation of the exterior flow and turbulence induced non-linear acoustic field using PowerFlow. The second step consists in the computation of the vibro-acoustic transmission through the window using the finite element vibro-acoustic solver Actran. Additionally in order to validate the numerical process, an experimental set-up has been created based on the simplified vehicle. The vibration of the windshield and windows, the total wind noise level results and the relative contributions of the different windows are then presented and compared to measurements. The influence of the flow yaw angle (different wind orientation) is also assessed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.427-430
• /
• 2012

최근 차량용 블랙박스, 자동 운전 시스템, 어라운드 뷰 시스템 등과 같은 운전자의 편의와 안전을 위한 장치 및 시스템들이 개발되고 있다. 현재 운전자를 위한 보조 시스템으로 구글(google)의 자동 운전 시스템(Auto Car Driving System)과 현대 모비스(hyundai mobis)의 AVM 시스템(Around View Monitoring System) 등의 다양한 차량용 편의장치 시스템들이 등장했다. 위와 같은 다양한 ECU들을 관리하기 위한 서버 및 저장 장치 역할을 할 수 있는 고사양의 Car PC의 장착이 필수적이다. 기존의 AVM 시스템은 차량 주변을 실시간으로 제공하기 위해 임베디드 또는 별도의 차량용 네트워크를 통해 임베디드 시스템 또는 SoC(System On Chip)형태의 하드웨어 기반으로 개발되고 있다. 하지만 고사양의 Car PC 기반에서는 별도의 비용없이 소프트웨어로 구현이 가능하다. 본 논문에서는 차량의 전 후 좌 우에 장착된 4대의 카메라로부터 입력된 차량 주변 상황을 한눈에 보여주는 AVM 시스템(Around-View Monitoring System)을 위한 카메라 보정 및 정합 처리 모듈 및 AVM 시스템을 Windows를 O/S로 하는 PC 내부에서 기존의 AVM 시스템을 이용하여 화면에 전 후 좌 우 버튼을 각각 만들어 버튼을 터치했을 때, 각 버튼에 해당되는 영상이 AVM 시스템과 함께 출력되도록 하거나 디스플레이에 Full 버전으로 출력되도록 S-UI(Smart User Interface)를 설계 및 구현한다. 제안하는 AVM 시스템과 기존의 AVM 시스템의 성능과 기능을 비교 분석함으로써 제안하는 영상 처리 모듈을 이용하여 추가 비용이 발생하지 않는 AVM 시스템의 구현 가능성을 검증한다.