• Journal of Advanced Marine Engineering and Technology
• /
• 제38권2호
• /
• pp.154-161
• /
• 2014

This research presents results of structural designs and evaluations for 3MW Wind Turbine Blade by FEM analysis. After the GFRP model was designed as a baseline model, failure check by Puck's failure criterion and buckling analysis were accomplished to verify safety of wind turbine blade in the critical design load case. Moreover, applicability of two kinds of carbon spar cap model, was studied by comparing total mass, price and tip deflection to the GFRP model. The results showed that the GFRP model had sufficient structural integrity in the critical design load case, and the carbon spar cap model could be a reasonable solution to reduce weights, tip deflections.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.333-334
• /
• 2006

A novel mathematical modeling in web transport systems for Continuous Annealing Processes (CAP) is proposed. Despite of thermal and weight effects in dynamics of web transport systems, the conventional mathematical model does not consider those effects. Disregard of these effects causes the low manufacturing quality of webs in CAP. In order to improve the manufacturing quality of webs in CAP, moreover, precise tension control is required based on the mathematical model. Therefore, an advanced mathematical model considering thermal and weight effects in CAP should be established. The effectiveness of a novel mathematical model is evaluated by comparing the performances of the PI tension control system based on the proposed mathematical model with that based on the conventional one through the computer simulation.

• 한국지반환경공학회 논문집
• /
• 제19권7호
• /
• pp.5-11
• /
• 2018

Instead of a single pile, group piles are usually used for the pile foundation. If the earthquake occurs in the ground where group piles are installed, dynamic behavior of group piles are affected not only by interaction of piles and the ground movement but also by the pile cap. However, in Korea, the pile cap influence is not taken account into the design of group piles. Research on dynamic behavior of group piles has been performed only to verify interaction of piles and the ground and has not considered the pile cap as a factor. In this research, 1g shaking table model tests were performed to verify the thickness of the pile cap affects dynamic behavior of group piles that were installed in the ground where the earthquake would occur. The test results show that, as thickness of the pile cap increased, acceleration and horizontal displacement of the pile cap decreasd while vertical displacement of the pile cap increased. The results also showed that, among the group files tested, acceleration, horizontal displacement, and vertical displacement of the bearing pile are smaller than those of the friction pile.

• 대한토목학회논문집
• /
• 제14권6호
• /
• pp.1405-1415
• /
• 1994

탄소성(彈塑性) 변형경화(變形硬化) 거동(擧動)을 하는 흙은 토질(土質)의 상태(狀態)와 시험조건(試驗條件)에 따라 다양(多樣)한 응력경로(應力經路)를 갖는다. 체적비(體積比) ${\upsilon}$인 흙을 주응력공간(主應力空間)에서 표시(表示)하면 불규칙육각형(不規則六角形)피라밋에 캡을 씌운 형상(形狀)이다. 캡은 ${\upsilon}$값이 변(變)하면 그 크기가 달라지나 형상(形狀)은 항상 닮은 꼴이며 소성체적변형(塑性體積變形)의 증감(增減)에 따라 이동(移動)이 결정된다. 이와 같은 토질특성(土質特性)을 반영하여 현재(現在)까지 많은 학자(學者)들이 캡모델을 연구발표(硏究發表)하였으며 본(本) 연구(硏究)에서는 비선형(非線形) 탄성변형(彈性變形) 경화(硬化) 소성(塑性) 캡과 Mohr-Coulomb의 파괴곡면(破壞曲面)을 접합(接合)한 흙의 구성(構成) 모델(M-C 캡모델)의 함수식(函數式)을 유도(誘導)하였다. 변형경화(變形硬化) 소성(塑性) 캡모델을 사용(使用)한 해석(解析)의 결과(結果)에 의하면 정규압밀(正規壓密) 상태(狀態)에서는 전단(剪斷)을 통한 경화(硬化)와 소성(塑性)흐름(캡의 이동(移動))의 형상(形狀)을 보여주고 있으나 과압밀상태(過壓密狀態)의 전단(剪斷)에서는 파괴포락선(破壞包絡線)에 도달할 때까지 탄성거동(彈性擧動)을 보이고 캡은 이동(移動)하지 않았다.

• 한국건설관리학회논문집
• /
• 제5권5호
• /
• pp.93-100
• /
• 2004

For accurate construction contract time estimation, few parameters are more significant than crew production rates and factors affecting the rates. However, statistical analysis techniques for finding such factors are not always simple mainly because there are many factors and the interaction between factors is not well quantitatively understood. This paper presents methodology of identifying factors driving crew production rates. The methodology is further demonstrated with representative data collected by the author from 13 on-going highway constructions. Three factors were identified as statistically significant drivers of Cap crew production rate: 'Cap Size (m3/ea)'; 'Cap Length (m)'; and 'Cap Shape (Rectangle vs. Inverted 'T')'. It was also found that the production rates are best explained by a multiple regression model with two of the drivers; 'Cap Size' and 'Cap Shape'.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.445-448
• /
• 2001

Noise radiated from pile driving operation is one of major sources of community noise pollution and thus its operation method is strictly restricted by regulations. Although the drilling method is now used been commonly used in urban areas because of its activity, the benefit of low noise decreases due to high working cost. In the present work, noise characteristics of pile driving operation are carried out. Based on the study result, a low-noise pile cap for driven piles is developed in order to satisfy both the noise level restriction and the economical efficiency. Effects of pile cap are investigated by a scale model experiment, which is focused on the variation of impact force and sound pressure level. The results show a good possibility of noise reduction by an appropriately designed pile cap.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1324-1331
• /
• 2002

Densification behavior of composite powders was investigated during cold compaction. Experimental data were obtained for aluminum alloy powder mixed with zirconia powder inclusion under triaxial compression. The Cap model with constraint factors was implemented into a finite element program (ABAQUS) to simulate compaction responses of composite powders during cold compaction. Finite element results were compared with experimental data for densification behavior of composite powders under cold isostatic pressing and die compaction. The agreements between experimental data and finite element calculations from the Cap model with constraint factors were good.

• 한국생산제조학회지
• /
• 제21권1호
• /
• pp.21-25
• /
• 2012

In this study, the safest model can be selected by the simulation result of structural safety analysis according to the shape of impact bar affected at side door of automobile. The open sectional model of semicircle type has the lowest deformation and stress among 4 kinds of models. As the weight of this model has 30% in comparison with other models, it becomes most economical and stable. As the open sectional model of cap type the highest deformation and stress among 4 kinds of models, it becomes weakest. The closed models with circular and rectangular types has the stress far lower than cap type. The maximum deformation is shown at the center part of impact bar but the maximum stress occurs at the joint part between impact bar and frame.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.179-180
• /
• 2006

Densification behavior of various metal and ceramic powder was investigated under cold compaction. The Cap model was proposed based on the parameters obtained from axial and radial deformation of sintered metal powder compacts under uniaxial compression and volumetric strain evolution. For ceramic powder, the parameters were obtained from deformation of green powder compacts under triaxial compression. The Cap model was implemented into a finite element program (ABAQUS) to compare with experimental data for densification behavior of various metal and ceramic powder under cold compaction.

• 환경영향평가
• /
• 제16권1호
• /
• pp.1-13
• /
• 2007

This study was carried out to estimate the emission reduction rates for the regional allowable emissions by special measures to achieve the target air quality in Seoul Metropolitan Area (SMA). A modeling system was designed to validate the details in enforcement regulations set up by local governments based on the current status and plans for air quality improvement. Modeling system was composed of meteorological model (MM5), emission model (SMOKE), and air quality model (CMAQ). Predicted results by this system show quiet well not only daily air pollutants concentration but also the tendencies of wind direction, wind speed and temperature. To achieve the target air quality in Seoul Metropolitan Area (SMA), emission allowances are estimated by seasons and regions. Referring to the base year 2002, it was estimated that emission reduction rates to achieve the intermediate goal in 2007 were 14.2% and 16.6% for NOx and $PM_{10}$, respectively. It was also estimated that 52% of NOx and 48% of $PM_{10}$ reductions from the base year 2002 would be required to accomplish the air quality improvement goal of 22 ppb for $NO_2$, and $40mg/m^3$ for $PM_{10}$ in year 2014. To improve $NO_2$ and $PM_{10}$ concentration through emissions reduction policies, it was found that emissions reduction for the on-road mobile sources would be the most effective in SMA.