• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.185-192
• /
• 2002

This paper focused on the dynamic behavior of camshaft in a direct acting type valve train system. To investigate camshaft behavior, transient vibration analysis is performed by using the transfer matrix method. The camshaft is treated as lumped mass system supported by spring and damper. Front the presented analytical model, we could predict dynamic behavior of camshaft, shaft locus within bearing and bearing load. The presented mode and results will be very helpful to design the optimal camshaft and valve train system.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.167-175
• /
• 1997

The locus of a camshaft supported on camshaft bearings has been investigated using transient method. Forces applied to camshaft are composed of two components, one is transfer force between cam and tappet, the other is frictional force. These forces have been calculated using lumped mass model and EHL theory. ADI method has been used for numerical analysis of Reynolds equation, and 4th order Runge-Kutta method has been used for transient journal locus analysis. The effects of various load conditions are presented in the form of journal locus. As the result of analysis, it is found that camshaft bearings exist in the hydrodynamic lubrication condition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.34-43
• /
• 2002

This paper focused on the dynamic behavior of camshaft in a direct acting type valve train system. To investigate camshaft behavior, transient vibration analysis is performed by using the transfer matrix method. The camshaft is treated as a lumped mass system supported by spring and damper, From the presented analytical model, we could predict dynamic behavior of camshaft, shaft locus within bearing and bearing load. The presented model and results will be very helpful to design the optimal camshaft and valve train system.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.53-59
• /
• 1997

The camshaft locus at camshaft beating in a direct acting OHC valve train system has been investigated using the transient method. Forces applied to the camsfiaft are composed of two components, one is the transfer force between the cam and the tappet, the other is the frictional force. These forces have been calculated using the lumped mass model and the elastohydrodynamic lubrication theory. The alternating direction implicit method has been used for the numerical analysis of Reynolds equation, and 4th order Runge-Kutta method has been used for the transient journal locus analysis. The effects of various load conditions are presented in the form of journal locus. As a result of the analysis, it has been found that camshaft bearings were mainly in the hydrodynamic lubrication condition.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.3
• /
• pp.46-52
• /
• 2009

Nowadays, many components in automobile, aircraft, offshore structure and industry require lightness and high strength. However, since developments of advanced materials have limitations, it mainly is applying to method of surface hardening. This study offered research about camshaft that is one among engine important component. The material used in this study is 0.53% carbon steel as structure material of camshaft, splineshaft, coupling, pulley, driveshaft et cetera. Camshaft is processed using mainly carbon steel, and receives wear and fatigue by special quality high speed of parts. Therefore, camshaft need surface hardening to improve camshaft's fatigue life and increase durability of engine. This study compare to residual stress and martensite microstructure created by high frequency induction treatment, and these results lead to the conclusion of fatigue crack growth characteristics.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1997.10a
• /
• pp.20-20
• /
• 1997

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.21-27
• /
• 2015

In order to meet the current emission regulations (EURO-6), it is necessary to significantly reduce $CH_4$ and $NO_X$ emissions. This study investigated the effect of a reduction in the valve overlap on the combustion and emission characteristics of a hydrogen-compressed natural gas engine under a part-load operating condition. The combustion and emission characteristics were analyzed for each fuel using the original camshaft and an altered camshaft with reduced valve overlap. The results showed that the thermal efficiency was decreased and the fuel flow was increased when using the altered camshaft. The $CO_2$ and $CH_4$ emissions were increased as a result of the reduced thermal efficiency. Under lean operating conditions, the $NO_X$ emission was decreased compared with one of the conventional camshaft. Thus, under the same fuels and operating conditions, it had a harmful influence on the emission characteristics and thermal efficiency.

• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.23-27
• /
• 1998

The characteristics of friction in direct acting OHC vane train system have been investigated by the comparison of experimental and theoretical results. A modified friction model was presented to calculate the friction force at cam/tappet contact. A simple experimental system was evaluated to measure the friction force and the camshaft driving torque. The friction force was measured by using the dynamic loadcell. Good agreement was found between theoretical and experimental results in friction force, but there was a little difference in driving torque.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.3
• /
• pp.208-213
• /
• 2013

To get vibration responses, a camshaft is modelled as an unbalanced multiple rotor bearing system. Because of complex geometry and complicated load conditions, the finite element method is used. After the finite element equation of the system is constructed, Newmark's method is used to get the vibration responses. Whirl vibration responses of a V-8 engine camshaft are estimated and compared with measured responses. After the fluctuating stresses are obtained, fatigue analysis is performed based upon the modified Goodman's equation. Stress concentration effects are considered. In the whirl vibration of camshafts, the bending effect is dominant, and the bending deformation is dependent upon the span length between the adjacent bearing journals. For high speeds, the fluctuations of excitation forces are large, and it is known that nonlinear time varying bearing coefficients should be used for analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.78-87
• /
• 1998

A dynamic model of direct-acting OHC valve train system has been used to determine the load conditions in the system. The modified equations for calculating the friction forces between cam and HLA, and at a camshaft bearing have been defined considering the lubrication conditions. Then, to understand the frictional characteristics in the system, a parameter study has been performed. As the results of the analysis, valve spring stiffness and preload have great effects on the friction in the system, but the effects of other parameters are negligible. So, how to design the valve train system with respect to the reduction of friction is to minimize the valve spring stiffness and preload in the limit of satisfying the dynamic constraints.