• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.3
• /
• pp.177-184
• /
• 2020

Purpose: The purpose of this study was to compare and evaluate the tensile bond strength of chairside reline resin to denture base resin fabricated by different methods (subtractive manufacturing, additive manufacturing, and conventional heat-curing). Materials and methods: Denture base specimens were fabricated as cuboid specimens with a width of 25 mm × length 25 mm × height 3 mm by subtractive manufacturing (VITA VIONIC BASE), additive manufacturing (NextDent Base) and conventional heat-curing (Lucitone 199). After storing the specimens in distilled water at 37℃ for 30 days and drying them, they were relined with polyethyl methacrylate (PEMA) chairside reline resin (REBASE II Normal). The subtractive and additive manufacturing groups were set as the experimental group, and the heat-curing group was set as the control group. Ten specimens were prepared for each group. After storing all bound specimens in distilled water at 37℃ for 24 hours, the tensile bond strength between denture bases and chairside reline resin was measured by a universal testing machine at a crosshead speed of 10 mm/min. The fracture pattern of each specimen was analyzed and classified into adhesive failure, cohesive failure, and mixed failure. Tensile bond strength, according to the fabrication method, was analyzed by 1-way ANOVA and Bonferroni's method (α=.05). Results: Mean tensile bond strength of the heat-curing group (2.45 ± 0.39 MPa) and subtractive manufacturing group (2.33 ± 0.39 MPa) had no significant difference (P>.999). The additive manufacturing group showed significantly lower tensile bond strength (1.23 ± 0.36 MPa) compared to the other groups (P<.001). Most specimens of heat-curing and subtractive manufacturing groups had mixed failure, but mixed failure and adhesive failure showed the same frequency in additive manufacturing group. Conclusion: The mean tensile bond strength of the subtractive manufacturing group was not significantly different from the heat-curing group. The additive manufacturing group showed significantly lower mean tensile bond strength than the other two groups.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.19 no.1
• /
• pp.3-11
• /
• 2015

Purpose It is hard to obtain high quality images of knee and T.M joint because of a lot of soft tissues in the knee and T.M joint area. Most conventional system for high resolution scintigraphy was used by 4 mm aperture pinhole collimator. Performance comparison of high-resolution pinhole SPECT for Micro deluxe phantom using conventional system. the aim of this study is to evaluate performance of each aperture according to the diameter size and the usefulness of 24-hour delayed bone scintigraphy. Materials and Methods In this study 6 mm, 8 mm diameter pinhole collimators were mounted on Siemens E.CAM systems. In order to evaluate performance evaluation of each aperture and Micro Deluxe phantom was used for performance comparison of conventional SPECT system, Projection data were obtained with 9 degree increment per 30 second. Transverse images were reconstructed using dedicated OSEM algorithm with recovery of detector blurring. $^{99m}Tc-HDP$ source was used for 24-hour delayed bone scintigraphy. Results The knee joint images obtained with 24-hour delay were improved more than those obtained with 3-hour delay in our study. The 6 mm and 8 mm pinhole collimators FWHM have improved by 28% SNR and Uniformity have improved by 35%, Contrast has improved by 7% in 24-hour delayed knee joint image. While in 24-hour delayed T.M joint image of the 6 mm and 8 mm pinhole collimators FWHM have decreased by 60% SNR has decreased by 20% and Uniformity has decreased by 25%, Contrast has decreased significantly. Conclusion Pinhole collimators with 6 mm and 8 mm diameter could offer a superior performance for 24-hour delayed bone scintigraphy. The use of 24-hour delayed image provides additional benefits for pinhole scintigraphy of knee joint. Therefore, we expect that it is useful for precise diagnosis of knee joint and it is applicable to others joint imaging.

• Journal of Korean Historical Folklife
• /
• no.34
• /
• pp.253-281
• /
• 2010

This study has its purpose on figuring it out to the religious notion in Vietnam with the material of the divinity construction of Den Hang Pho in Sapa where is the northern region of Vietnam. To make this, the study divides the type of Vietnamese temples into four parts; Chua, Den, Dinh, and Mieu. Among them, the study pays attention to 'Den' because Vietnamese historical heroes are seated as divinity. This reason makes a reasonable case to this study to figure out a typically and generally religious faith. First of all, the study analyzes immaculate divinity, which generally consists of three and four layered system. The study confirms that the immaculate divinity started from the goddess and then extended to the concept to dominate the sky, the ground, the sea(river), and the mountain(forest). General Tran Hung Dao is the best historical hero in Vietnam and has been placed in temples called Den. The study exams the context that the divinity extended to the religious beliefs, for examples, the belief related in a childbirth by lots of narrations and ceremonies and the belief to treat a sickness, and also exams the context that the divinity placed in a divinity to make a symmetrical relation with immaculate faith. The study exams the divinity construction of Den Hang Pho as its authentic case. In this case, the study could verify a case emphasized by mountain Holy Mother among immaculate faiths. Especially, the study can confirm that General Tran Hung Dao was apotheosized as a concept to be symmetrized with immaculate divinity, and futhermore, a couple of snakes was emphasized by their positioning to every room. Tri-system lays stress on the aboriginality(locality) centered on minority races in the northern Vietnam, the national identity of Vietnam, and the ecological condition of rivers flowing the valley of high and steep peak. The confirmed facts could be said to a construction what the religious notion of tri-system makes. The study makes a conclusion that this kind of conversion-oriented religious notion naturally corresponded with region, nation, and ecologically environmental condition, and extended to the Vietnamese faith with polytheistic divinity.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.4
• /
• pp.395-404
• /
• 2021

Purpose. The purpose of present study was to evaluate the effect of changing structural stability of wax disc on the fit of prosthesis when the milling proceeded in order. Materials and methods. Prepared maxillary left first molar was used to fabricate a Ni-Cr alloy reference model. This was scanned to design crown and then wax pattern was milled, invested and cast to fabricate prosthesis. The wax patterns located in a row centrally within a single wax disc were set into a total of five groups ranging from WM1 group that was first milled to WM5 group that was last milled and the number of each group was set as 10. Silicone replica technique was used to measure the marginal gap, axial internal gap, line angle internal gap, occlusal internal gap. Data was evaluated with one-way ANOVA with significance level set at α = .05 and then Tukey HSD test was conducted for post analysis. Results. Marginal gap measured in each group, it was 40.41 ± 2.15 ㎛ in WM1 group, 40.44 ± 2.23 ㎛ in WM2 group, 39.96 ± 2.25 ㎛ in WM3 group, 39.96 ± 2.48 ㎛ in WM4 group, and 40.57 ± 2.53 ㎛ in WM5 group. No significant difference was found between groups. The significant difference between the groups was also not found in the axial internal gap, line angle internal gap, and occlusal internal gap. Conclusion. Internal and marginal fit of single crown to the sequential order of milling processing in the single machinable wax disc did not seem to be affected by the sequence.

• Journal of Korea Entertainment Industry Association
• /
• v.14 no.4
• /
• pp.289-303
• /
• 2020

The purpose of this study is to provide adequate datas on number of people who are in golf related field and also further expend that number for golf industry. The main stream of this study is to map out present golf related jobs and how this study can help golf industry in general. To make a greater improvements on golf industry with more job opportunity following ideas were presented. First, improving education on "hand on experiences on the field of golf industry" Better educating potential employees for golf industry for the right positions can enhance overall work environment. To do so, the society and the schools must come to agreement to provide adequate curriculum for people. Second, implementing "a golf club division program." The support from Ministry of Culture and Sports and Tourism Department, which are govern by Republic of Korea, are aggressively working to expend the golf business and also recruit elite personnel like former tour players to work on the field to better operate the whole system. Third, performing a thorough research on current golf related jobs and numbers and diversity on the field. Fourth, developing a specific and a differentiated golf job fields for better future for people and students who majored in golf industry. So that they cam feel secured and have a sense of dignity. Finally, strengthening the golf industry's competitiveness. The golf related companies have to step up to higher gear. With working in harmony between golf industry and government can assure of brighter future for our next generation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.3
• /
• pp.189-197
• /
• 2023

Purpose. This study aimed to compare and evaluate the shear bond strength between various temporary prostheses resin blocks fabricated by subtractive and additive manufacturing methods bonded to self-curing reline resin. Materials and methods. The experimental groups were divided into 4 groups according to the manufacturing methods of the resin block specimens and each specimen was fabricated by subtractive manufacturing (SM), additive manufacturing stereolithography apparatus manufacturing (AMS), additive manufacturing digital light processing manufacturing (AMD) and conventional self-curing (CON). To bond the resin block specimens and self-curing resin, the reline resin was injected and polymerized into the same location of each resin block using a silicone mold. The shear bond strength was measured using a universal testing machine, and the surface of the adhesive interface was examined by scanning electron microscopy. To compare between groups, one-way ANOVA was done followed by Tukey post hoc test (α = 0.05). Results. The shear bond strength showed higher values in the order of CON, SM, AMS, and AMD group. There were significant differences between CON and AMS groups, as well as between CON and AMD groups. but there were no significant differences between CON and SM groups (P > .05). There were significant differences between SM and AMD groups, but there were no significant differences between SM and AMS groups. The AMS group was significantly different from the AMD group (P < .001). The most frequent failure mode was mixed failures in CON and AMS groups, and adhesive failures in SM and AMD groups. Conclusion. The shear bond strength of SM group showed lower but not significant bond strength compared to the CON group. The additive manufacturing method groups (AMS and AMD) showed significantly lower bond strength than the CON group, with the AMD group the lowest. There was also a significant difference between the AMD and SM group.

• Korean Journal of Poultry Science
• /
• v.50 no.4
• /
• pp.231-240
• /
• 2023

Infectious bursal disease (IBD) is an acute, highly contagious, and immunosuppressive disease in young chickens, and causes considerable economic losses to the poultry industry. More than 30 years ago, an antigenic variant IBDV (avIBDV) was reported in chicken farms in the United States. Recently, a novel avIBDV exhibited clear differences in molecular characteristics compared with previous variant strains. This study investigated the molecular characteristics of recently isolated avIBDV strains in Korea. Strains of avIBDV were confirmed by reverse transcription PCR (RT-PCR) and were propagated in 10-day-old specific-pathogen-free (SPF) embryonated chicken eggs through chorioallantoic membrane (CAM) inoculation. Multiple sequence alignment and phylogenetic analyses of hypervariable regions VP2 gene revealed that the strains originated from two different avIBDV lineages (G2a and G2d). In our results, we confirmed the co-existence and prevalence of avIBDV genogroup G2a and G2d in chicken farms. It is necessary to study the protective efficacy of current vaccines against avIBDVs.