• Nuclear Engineering and Technology
• /
• v.55 no.5
• /
• pp.1885-1891
• /
• 2023

The present work aims to fabricate Na_1+xZr₂Si_xP_3-xO₁₂ compound at various calcination temperatures based on the zircon mineral. The fabricated compound was calcinated at 250, 500, and 1000℃. The effect of calcination temperature on the structure, crystal phase, and radiation shielding properties was studied for the fabricated compound. The X-ray diffraction diffractometer demonstrates that, the monoclinic crystal phase appeared at a calcination temperature of 250℃ and 500℃ is totally transformed to a high-symmetry hexagonal crystal phase under a calcination temperature of 1000℃. The radiation shielding capacity was also qualified for the fabricated compounds using the Monte Carlo N-Particle transport code in the g-photons energy interval between 15keV and 122keV. The impacts of calcination temperature on the g-ray shielding behavior were clarified in the present study, where the linear attenuation coefficient was enhanced by 218% at energy of 122keV, when the calcination temperature increased from 250 to 1000℃, respectively.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.1-10
• /
• 1995

Effects of calcination temperature on microstructure and electric-magnetic properties of Mg-ferrite were investigated. As the calcination temperature increase, the green density and the sintered density increase due to the enhancement of densification of calcined powder. The grain size in the sintered ferrite increases with increasing the calcination temperatures from 800 to 100$0^{\circ}C$, but decreases from 1000 to 120$0^{\circ}C$. The resistivity decreases with increasing the calcination temperatures from 800 to 110$0^{\circ}C$, but increases from 1100 to 120$0^{\circ}C$ due to the microstructure which consists of small, uniform grian size and pores at grain boundaries. Magnetization increases slightly due to the increasement of the sintered density while Curie temperature is almost constant regardless of calcination temperatures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.305-306
• /
• 2005

In this paper, in order to develop Pb-free piezoelectric ceramics, $(Li_{0.04}Na_{0.44}K_{0.52})(Nb_{0.86}Ta_{0.10}Sb_{0.04})O_3$ ceramics were fabricated with the variation of calcination temperature and sintering temperature. Specimens couldn't be sintered below $111^{\circ}C$ and showed the largest density at calcination temperature of $800^{\circ}C$. Specimens manufactured with the variation of calcination temperature showed pseudo-tetragonal phase, and showed the optimal values of kp=0.45, ${\varepsilon}r$=1336 and $d_{33}$=254 at calcination temperature of $800^{\circ}C$ and sintering temperature of $1110^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.659-667
• /
• 1997

The effect of calcination temperature of Mg(OH)2 on the green density and densification of MgO was investigated. It was observed that the impure magnesium hydroxide powder showed a higher crystallization rate while it had a lower tendency of agglomeration between periclae crystallites, as compared to that of the pure magnesium hydroxide powder. In the case of calcination of the powders under 85$0^{\circ}C$, the impure powder showed the higher green and sintered density. In spite of higher green density upon the calcination over 100$0^{\circ}C$, the impure powder showed the lower sintered density, caused by exaggerated growth of the periclase crystallites. The highest sintered densities in the both powders were obtained at the calcination temperature of 100$0^{\circ}C$. And the green density was inversely proportional to the sintered density at the calcination over 100$0^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.217-221
• /
• 2008

In this study, We have been investigated the effect of calcination temperature and high-energy ball-milling of powder influences the $BaTiO_3$-based PTCR(Positive Temperature coefficient Resistance) characteristics and microstructure. The mixed powder was obtained from $BaCO_3$, $TiO_2$, $CeO_2$ ball-milled in attrition mill. The mixed powder was calcine from 1000 $^{\circ}C$ to 1200 $^{\circ}C$ in air and then it was sintered in reduction- re-oxidation atmosphere. As a result, The room-temperature electrical resistivity decreased and increased with increasing calcination temperature. specially, Attrition milled powder could have low room-temperature resistivity and high PTC jump order at 1100 $^{\circ}C$. attrition milling had lower room-temperature resistivity than ball milling. Particle size decreased by Attrition milling of powder influences in calcination temperature and room-temperature resistivity.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.279-283
• /
• 2000

Lime is one of the world's most useful chemicals and manufactured in various types of kilns, using various fuels. Quicklimes vary in reactivity with water due to variations in the time and temperature calcining process and type of kiln used. Careful attention and control of time and temperature in the calcining process is necessary to insure a highly reactive lime. Excess time and temperature will cause the lime to be over burned. The highest reactivity of quicklime is obtained by calcination of limestone in the particle size of 0.1cm~2cm, calcination temperature of $1000^{\circ}C$, calcination time 90min. It was found by the scanning electron microscopes that pores of quick lime is reducted if the soft burned quick lime is heated continually.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.9
• /
• pp.821-826
• /
• 2005

In this paper, in order to develop lead-free piezoelectric ceramics, $(Li_{0.04}Na_{0.44}K_{0.52)(Nb_{0.86}Ta_{0.10}Sb_{0.04})O_3$ ceramics were fabricated with the variation of calcination temperature and sintering temperature. The ceramics couldn't be sintered at temperature less than $1110^{\circ}C$ and showed the highest density at calcination temperature of $800^{\circ}C$. Crystal structure of the ceramics showed pseudo-tetragonal phase. At the calcination temperature of $800^{\circ}C$ and sintering temperature of $1110^{\circ}C$, the optimal values of $density=4.64g/cm^3,\;kp=0.45,\;{\varepsilon}r=1336,\;d_{33}=254pC/N\;and\;Tc=335^{\circ}C$ were obtained.

• Journal of Environmental Science International
• /
• v.14 no.9
• /
• pp.889-896
• /
• 2005

The nanosized $TiO_2$ photocatalysts were prepared by the hydrolysis of $TiCl_4$ and calcined at different temperatures. The resulting materials were characterized by TGA, DSC, XRD, and TEM testing techniques. XRD, TEM, and BET measurements indicated that the particle size of $TiO_2$ was increased with rise of calcination temperature and surface area was decreased with rise of it. The prepared $TiO_2$ photocatalysts were used for the photocatalytic degradation of congo red. The effects of calcination temperature, $TiO_2$ loading, the initial concentration of congo red, and usage frequencies were investigated and the rate constants were determined by regressing the experimental data. Calcination is an effective treatment to increase the photo activity of nanosized $TiO_2$ photocatalysts resulting from the improvement of crystallinity. The optimum calcination temperature of the catalyst for the efficient degradation of congo red was found to be $400^{\cric}C$. The rate constant was decreased with increase in the initial concentration of congo red and increased with increase in the $TiO_2$ loading. In the case of $TiO_2$ photocatalysts, the photocatalytic activity wasn't greatly affected by the usage frequencies.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2694-2698
• /
• 2012

Materials on the scale of nanoscale have widely been used as research topics because of their interesting characteristics and aspects they bring into the field. Out of the many metal oxides, zinc oxide (ZnO) was chosen to be fabricated as nanofibers using the electrospinning method for potential uses of solar cells and sensors. After ZnO nanofibers were obtained, calcination temperature effects on the ZnO nanofibers were studied and reported here. The results of scanning electron microscopy (SEM) revealed that the aggregation of the ZnO nanofibers progressed by calcination. X-ray diffraction (XRD) study showed the hcp ZnO structure was enhanced by calcination at 873 and 1173 K. Transmission electron microscopy (TEM) confirmed the crystallinity of the calcined ZnO nanofibers. X-ray photoelectron spectroscopy (XPS) verified the thermal oxidation of Zn species by calcination in the nanofibers. These techniques have helped us deduce the facts that the diameter of ZnO increases as the calcination temperature was raised; the process of calcination affects the crystallinity of ZnO nanofibers, and the thermal oxidation of Zn species was observed as the calcination temperature was raised.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.214-216
• /
• 2006

In this study, in order to develop the composition ceramics for low loss and low temperature sintering multilayer piezoelectric actuator, PMN-PZN-PZT ceramics were fabricated using two stage calcination method and $Li_2CO_3$, $Bi_2O_3$ and CuO as sintering aids and their piezoelectric characteristics were investigated according to the 2nd calcination and sintering temperature. At the calcination temperature of $750^{\circ}C$ and sintering temperature of $930^{\circ}C$, density, electromechanical coupling factor ($k_p$), mechanical quality factor ($Q_m$), Dielectric constant (${\varepsilon}_r$) and piezoelectric constant ($d_{33}$) of specimen showed the optimum value of $7.94g/cm^2$ 0.581, 1554, 1555 and 356pC/N, respectively for multilayer piezoelectric actuator application.