• Geomechanics and Engineering
• /
• 제33권5호
• /
• pp.519-528
• /
• 2023

In this paper, we present the results of an experimental study on the effect of polymer support fluid on shaft resistance of offshore bored piles. A series of pullout tests were performed on bored piles installed under various boundary conditions considering different types of grounds and support fluids, and a range of support fluid exposure times. Contrary to previous studies concerning onshore bored piles, a time dependent effect of polymer fluid on shaft resistance was observed in all ground types. The adverse effect of polymer support fluid on the shaft resistance, however, was considerably less than bentonite support fluid for a given exposure time. No significant reduction in shaft resistance was evident when limiting the exposure time of the polymer support fluid to the side wall of the borehole within 2-3 hours. The degree to which the polymer fluid affects shaft resistance seemed to vary with the ground type. A proper consideration should be given to the time dependent effect of polymer fluid on shaft resistance of bored piles installed in offshore construction environment to limit its adverse effect on the pile performance. The practical implications of the findings are discussed.

• 멤브레인
• /
• 제25권3호
• /
• pp.276-286
• /
• 2015

30 LMH의 정유량 플럭스로 운전하는 MBR에서, 휴지 및 역세정에 따른 한외여과 분리막의 오염을 조사하였다. 또한, 연속적인 공기세정과 비교하여 분리막 여과저항을 최소화하기 위한 간헐적인 공기세정을 평가하였다. 여과 조건은 14.5분 여과와 0.5분의 휴지를 유지하였으며, 역세정 시간은 휴지 시간과 동일하게 운전하였다. 공기세정이 정지하는 동안에 분리막 표면의 겔층 위에 케?이 빠르게 축척되었으며, 역세정으로 겔층과 케?층의 복합층은 쉽게 제거되었다. 역세정 후에 공기세정이 정지하는 동안 분리막 표면에 케?이 형성되어 공경 내부의 오염현상을 억제하였다. Pearson 상관성을 조사한 결과, 간헐적인 공기세정에서 공기 세정이 정지하는 시간과 분리막의 오염은 매우 연관성이 높다는 것을 알았다. 즉, 간헐적인 세정에서 공기세정이 정지하는 시간이 갈수록 오염억제에 효과적이었다.

• 멤브레인
• /
• 제9권1호
• /
• pp.36-42
• /
• 1999

본 연구에서는 Si 미립자를 함유한 반도체 세정폐수의 관형막을 이용한 한외여과특성을 검토하였다. 관형막의 시간변화에 따른 투과유속의 감소현상은 막표면에 형성된 케익층의 증가 및 기공막힘에 기인하며, cross flow는 케익여과에 의한 막오염 형태를 보였으나 dead-end flow는 기공막힘과 케익여과에 의한 혼합형태를 보였다. Cross Flow의 케익저항의 크기는 3.16$\times$$10^{12}$ ~4.34$\times$$10^{12}$ $m^{-1}$ 였고, dead-end flow 는 6.6 $\times$$10^{12}$ ~12.19$\times$$10^{12}$ $m^{-1}$였다. 운전초기의 흐름형태에 따른 투과유속은 cross flow 가 dead-end flow 의 약 7 배였다. Cross flow 투과유속은 약 42 $\ell$/$m^2$ hr, 용질배제율은 약 96 % 였으며, 분리막공정을 거친 투과수 중의 Si 입자의 평균크기는 20nm였다.

• Membrane and Water Treatment
• /
• 제9권5호
• /
• pp.373-383
• /
• 2018

Fouling by solids and microorganisms is the major obstacle limiting the efficient use of membrane wastewater treatment. In our previous study, two stages microalgae/membrane filtration system was proposed to treat anaerobic digested palm oil mill effluent (AnPOME). This two stages microalgae/membrane filtration system had showed great potential for the treatment of AnPOME with high removal of COD, $NH_3-N$, $PO_4{^{3-}}$, TSS, turbidity, and colour. However, fouling behavior of the membrane in this two stages microalgae/membrane filtration system was still unknown. In this study, empirical models that describe permeate flux decline for dead-end filtration (pore blocking - complete, intermediate, and standard; and cake layer formation) presented by Hermia were used to fit the experimental results in identifying the fouling mechanism under different experimental conditions. Both centrifuged and non-centrifuged samples were taken from the medium with 3 days RT intervals, from day 0 to day 12 to study their influence on fouling mechanisms described by Hermia for ultrafiltration (UF), nanofiltration (NF), and reverse osmosis (RO) filtration mode. Besides, a more detailed study on the use of resistance-in-series model for deadend filtration was done to investigate the fouling mechanisms involved in membrane filtration of AnPOME collected after microalgae treatment. The results showed that fouling of UF and NF membrane was mainly caused by cake layer formation and it was also supported by the analysis for resistance-in-series model. Whereas, fouling of RO membrane was dominated by concentration polarization.

• Korean Chemical Engineering Research
• /
• 제43권2호
• /
• pp.236-242
• /
• 2005

대표적인 단백질 물질인 bovine serum albumin(BSA), lysozyme, pepsin, casein 그리고 ovalbumin의 이성분계 단백질 혼합물의 미세 분리 막에서 보이는 막 오염 현상에 관한 실험을 고찰하였다. 트랙 에치법에 의해 제조된 $0.2{\mu}m$ 폴리카보네이트 미세 막을 이용하여 단백질 혼합물 용액의 조성과 종류가 여과유량감속에 미치는 영향에 대한 실험을 일정한 압력(14 kPa)과 수소이온농도(pH=11) 하에서 수행하였다. 각각의 이성분 단백질 혼합물에 대한 막오염 현상을 확인하였으며, 유량 감속 데이터는 최근에 개발된 pore blockage-cake formation 모델을 이용하여 분석한 결과, 실험 결과와 일치하였다. 이성분계 단백질 혼합물의 조성과 단백질 종류가 막오염 및 유속변화에 미치는 영향은 공극막힘속도(${\alpha}$), 단백질 침적층의 초기 저항($R_{po}$) 및 단백질 저항의 증가속도(${\beta}$)에 의해 설명 할 수 있었다. 대체로 공극막힘속도의 변화는 유속감소현상과 일치함을 알 수 있으며, 특히 casein이 존재하는 단백질 혼합물에서의 급격한 유량감속은 casein에 의한 단백질 침적층의 초기저항에 크게 기인된 것으로 판단된다.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1997년도 추계 총회 및 학술발표회
• /
• pp.120-122
• /
• 1997

1. 서론 : 본 연구에서는 매우 안정된 유동의 하나로 막 표면의 전단력을 향상시켜 여과가 진행됨에 따라 막의 표면에서 발생하여 여과선속을 저하시키는 케이크층의 형성을 억제하는 데에 효과가 있다고 알려진 Taylor와류를 응용한 회전막 여과기를 사용하여 여과실험을 수행함으로써 이러한 유동이 케이크층의 형성에 미치는 영향을 살펴보았다. 또한 여과선속에 영향을 미치는 여러 매개인자들을 포함하는 새로운 모델식을 제안하고 실험결과와 비교해봄으로써 그 타당성을 살펴보았다.

• 상하수도학회지
• /
• 제21권1호
• /
• pp.123-130
• /
• 2007

The effects of hydrogen peroxide treatment on the reduction of waterworks sludge were investigated in this study. Sludge treated by peroxidation $H_2O_2$ oxidation) was dewatered using a pressure filter at 3atm. It was observed that $H_2O_2$ treatment at the acidic condition significantly reduce both cake water content and specific resistance to filtration (SRF), indicating the enhancement of dewaterability and filterability. The filterability by hydrogen peroxide treatment at pH 3.5 was better than acidic treatment and became comparable with polymer conditioning. The sludge filterability evaluated by SRF was optimal at a dose 2ml $H_2O_2$/sludge($0.02g\;H_2O_2/gTS$) after adjusting of pH to 3.5. The $H_2O_2$ oxidation at pH 3.5 also produced even more dewatered cake when compared with polymer conditioning. The reduction rate of sludge mass at an optimal condition showed 34% compared with untreated sludge. The effects of peroxidation on sludge properties including zeta potential, bound water and particle size were also evaluated. Peroxidation at the acidic condition reduced both bound water and zeta potential. By $H_2O_2$ combined with sulfuric acid leached iron caused Fenton's reaction, which showed a potential to significantly reduce the amount of solids mass and to produce more compact cake with higher filterability.

• 상하수도학회지
• /
• 제25권5호
• /
• pp.681-689
• /
• 2011

Submerged membrane bio-reactor (SMBR) has several advantages such as high MLSS, long SRT, and low F/M ratio at wastewater treatment. So, this has widely applied over the world and many studies have been conducted. However, membrane fouling remains an inevitable problem. This study was investigated using bench-scale SMBR with three poeration modes. Raw waters were prepared by addition of starch, acetic and fibric acid to recovery water of zeolite. The efficiency of nitrification and COD were very stable as about 95% and 80%, respectively. And critical flux was 128.8L/$m^{2}$/hr. The result of biodegradability test was following values at the each mode : Ss+Xs/$C_{T}$=81.7%, 35.1% and 45.3%, $X_{I}+S_{I}/C_{T}=18.3%$, 64.9% and 54.7%. When particulate matters such as $X_{I}$ and $X_{S}$ in influent are increased, membrane fouling will take place more and more. A relative ratio of filtration resistance to the fouling occurred by the cake layer was increased when increased the portion of $X_{I}$ and polysaccharide. It was thought that the formation of cake layer was promoted due to bond between $X_{I}$ and vicid material s generated from the polysaccharide.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 2022년도 추계학술대회
• /
• pp.193-193
• /
• 2022

Cowpea(Vigna unguiculata L. Walp) has a low fat and protein content and a relatively high starch content, so it is mainly used in various ways for song-pyeon sediment, rice-cake paste, and porridge. In Yeonggwang-gun, Jeollanam-do, cowpea for seed production is being cultivated for the localization of raw material for Rice cake with ramie leave. A cowpea variety 'Jang-Alchan' was improved from the cross between IT145373 and IT145391 at the JARES in 2019. 'Jang-alchan' has an erect plant with an intermediate plant habit, light purple-colored corolla, and heart-shaped leaflets. 'Jang-alchan' has an orange-yellow seed seed-surface of faint luster, and brown and straight pods when matured. The stem length of 'Jang-alchan' was 48cm, 9cm longer than that of the control cultivar 'Okdang' and the 100-seed weight was 14.1g. The weight ratio of the seed coat for the entire seed was 11.2%, which was 0.2%p lower than that of the control cultivar. Field resistance of 'Jang-alchan' to leaf and systemic diseases was similar to that of the control cultivar. Is field resistance of 'Jang-alchan' to lodging was slightly lower than that of the control cultivar. The average yield of 'Jang-alchan' was 1.85ton per hectare, which was 14% higher than that of the control cultivar 'Okdang', 'Jang-Alchan' does not require the installation of an espalier-net and is taller than the existing supplied 'Okdang', so it can be harvested by combine harvesting. In addition, it is expected to contribute to the localization of raw material grains for regional specialties as it can be cultivated over a large area.

• 상하수도학회지
• /
• 제25권2호
• /
• pp.231-240
• /
• 2011

The objectives of this research are to investigate coagulation efficiencies of two coagulants l.e., alum and polyaluminum chloride and to understand effects of the coagulants on membrane fouling in microfiltration. The turbidity of supernatant from alum coagulation was increased with increasing doses whereas the turbidity from PACl coagulation was maintained at the low values. The observed injection volume of PACl for the same removal was approximately 30 percent less than alum, which produced a low sludge volume. The settling velocity of PACl flocs was greater than alum flocs. The results corresponded well with floc size measurements. Flux decline from alum coagulation was significant due in part to small sizes of flocs. At the low dose, alum floc had less specific cake resistance than PACl floc. However, as the dosage was increased, the increases in specific cake resistances of alum was substantial. Alum coagulation pretreatment needs careful operation to reduce membrane fouling by flocs. In general, PACl coagulants were more effective than alum coagulants for pretreatment of membrane processes because PACl showed the better performance in coagulation and membrane fouling.