• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.4
• /
• pp.589-598
• /
• 2000

A pilot-scale Spray Drying Sorber (SDS) system was set up to evaluate the effect of spray characteristics on the desulfurization yield. The size distribution and the Sauter Mean Diameters of slurry droplets were measured in advance using the optical size measurement system, Malvern 2600. The desulfurization yield of the drying chamber by size was measured for the conditions of inlet gas and spray injection. As a reagent, 10% limestone slurry of $Ca(OH)_2$ was treated with flue gas containing $SO_2$, and the combustion gas analyzer and gas detectors were attached to measure the $SO_2$ concentration. With a flow rate of 144 Nm3/h and a temperature range of $200{\sim}300^{\circ}C$, the experiments were performed for the Stoichiometric Ratio (SR) of 1.0 to 3.0 and droplet mean diameter of 6.5 to $34.3{\mu}m$. In case of smaller spray droplets, the desulfurization efficiency improved due to the increase of total droplet surface area, while the reduction in evaporation time reduced the contact time between the droplets and $SO_2$ gas. In some typical region of droplet diameter, this negative effect, reduction of contact time, became dominant and the desulfurization yield decreases the desulfurization yield in spite of the expansion in absorption area. These results revealed that there exists the optimal size of spray droplets for a given state, which is determined by the compromise between the total surface area of slurry droplets and the evaporation time of droplets. The measurements also indicated that the inlet temperature of flue gas changes the optimal injection condition by varying the driving force for evaporation. The results confirm that the effect of the evaporation time of slurry droplets should be considered in analyzing the desulfurization yield as well as the total surface area, for it is a significant aspect of the correlation with the capabilities of $SO_2$ absorption in wet droplets. In conclusion, the optimal condition of spray can be determined based on these results, which might be applied to design or scale-up of SDS system.

• Proceedings of the Korean Society of Embryo Transfer Conference
• /
• 2002.11a
• /
• pp.76-76
• /
• 2002

본 실험은 Piezo-미세조작기(PrimeTech Ltd., Japan)를 사용하여 마우스 핵이식 후 재구축배를 CZB와 KSOM 두가지 배양액을 사용하여 체외배양성적을 비교 검토하였다. MII의 미수정란은 성숙한 4~5주령 B6D2Fl에 hCG 주사 후 14시간째에 과적 방법을 통해 난관의 팽대부로 부터 회수하였고, metaphase II chromosome-spindle complex와 최소량의 세포질을 내경이 10$\mu\textrm{m}$인 피펫으로 흡입하여 탈핵하였다. 핵이식에 사용된 난구세포(8-l0$\mu\textrm{m}$)는 3시간동안 12% PVP 에처리 하여 piezo-미세조작기를 이용하여 세포질에 세포의 핵을 직접 미세주입 하였다. 핵이식 후 생존한 재구축배는 2시간동안 배양한 후 10mM SrC1$_2$와 5$\mu\textrm{g}$/$m\ell$의 cytochalasin B가 첨가된 $Ca^{2＋}$-free CZB에서 6시간 활성화 처리하였다, 활성화 처리 후 위전핵이 관찰된 재구축란을 CZB 와 KSOM 배지에서 배양하면서 발달률을 비교하였고, 상실배 및 배반포배로 발달한 재구축배를 day 3 대리모에 이식하였다. 표 1에서 보는 바와 같이 재구축배의 2-cell로의 발달률에 있어서 KSOM이 CZB에 비하여 유의적으로 높게 나타났으며(P<0.05), 또한 4-cell과 상실배/배반 포배로의 발달률에 있어서도 KSOM이 CZB에 비하여 유의적으로 높은 발달률을 나타내었다(P<0.01). 또한 KSOM 배지에서 배양된 상실배/배반포배를 대리모에 이식한 경우에 11.5 d.p.c에 생존한 태아가 관찰되었다. 이상의 결과로 핵이식 재구축배의 활성화 처리 후의 발생에는 KSOM 배지가 CZB 배지에 비하여 유효함을 확인 할 수 있었다.그와 같은 배양 기술을 이용하여 외래유전자를 도입한 일련의 결과에 관하여 보고 하고자한다., 이것은 세포내 유전자가 transfection되지 않은 세포도 neo selection에서 선발된다는 것을 제시하고 있다. 따라서 체세포를 이용한 형질전환동물 생산을 위해서는 세포내 유전자 도입과 선발 과정에서 나타난 colony에 대하여 보다 엄격한 screen을 하는 것이 필요한 것으로 생각된다.로 우점하였다. 여름철 식물플랑크톤 대발생에 영향은 수온과 직산염이 중요하였으나, 부유물질 크게 기여하지 못하였다.애를 확인하고 지도 관점을 파악하는 것을 포함한다. 그러나 본 논문은 역사발생적 수학 학습-지도 원리의 실제적인 적용에 관하여는 기초적인 연구에 지나지 않기 때문에, 역사발생적 원리를 학교수학에 실제적으로 적용하기 위해서는 각각의 내용에 대한 철저한 역사적 분석을 바탕으로 하는 후속 연구가 필요하다./TEX>구성교육${\lrcorner}$이 조선총독부의 관리하에서 실행되었다는 것을, 당시의 사범학교를 중심으로 한 교육조직을 기술한 문헌에 의해 규명시켰다.nd of letter design which represents -natural objects and was popular at the time of Yukjo Dynasty, and there are some documents of that period left both in Japan and Korea. "Hyojedo" in Korea is supposed to have been influenced by the letter design. Asite- is also considered to have been "Japanese Letter Jobcheso." Therefore, the purpose of this study is to look into the origin of the letter designs in t

• Journal of the Korea Organic Resources Recycling Association
• /
• v.4 no.2
• /
• pp.35-45
• /
• 1996

In order to investigate the possibility of treating nightsoil sludge, the growth trend experiments with vermicompsting was performed and the stability of worm castings was evaluated by the analysis of minerals according to growth periods. Survival rate(SR) of earthworms decreased as earthworms grow up to 7 weeks. The growth period of the earthworms could be classified into two phases on the basis of the ratios of cast to feed ingested(ID). The growth period of the earthworms up to 3 weeks, the high percentage of dry weight of feed ingested(ID) is mainly utiliz-ed to an increase in fresh weight of earthworms, and after the 3 weeks, it is utilized to cast production in this experiment, respectively. The highest values of increasing rate(IR) and biomass of the earthworms(BE) were obtained at 3 weeks and those were 10.59mg/day and 14.48g, respectively. Between the increasing rate(IR) and biomass of the earthworms(BE), a highly positive correlation coefficient(p<0.001) ap-peared. The highest values of biomass of the earthworms(BE) and cast production(CW) were obtained at 3 and 7 weeks, respectively. All the concentrations of minerals except calcium(Ca) in worm castings was lower than the values in nightsoil sludge. It was considered that the major portion of minerals in nightsoil sludge may have been retained in the bodies of earthworms. And these values were lower than the regulated levels in organic fertilizers that the regula-tion standards. In conclusion, the worm castings are very stable for the use as soil conditioner or organic fertilizers.

• Membrane Journal
• /
• v.18 no.3
• /
• pp.241-249
• /
• 2008

This study is to concentrate vanadium in Jeju groundwater using reverse osmosis processes, and to utilize the concentrate for vanadium water. Groundwater samples were taken from Wahyul, Ayum, and Seogwipo groundwater wells with different in vanadium content each other. Their vanadiuln concentrations were 31.8, 44.5, and 53.0 ppb, respectively. The rejection coefficients of every component in groundwater were increased with the increase of TMP At the TMP of $8 kg_f/cm^2$, the rejection coefficients of vanadium, sodium, potassium, aluminium, iron, and barium were $97.4%{\sim}99.0%,\;97.7%{\sim}97.8%,\;98.0%{\sim}98.3%,\;94.8%{\sim}97.5%,\;88.0%{\sim}96.4.0%$, and $97.9{\sim}98.0%$, respectively. And those of magnesium, calcium, chromium, mauganese, and strontium in three groundwater were more than 99.0% at the same TMP. It was possible that vanadium contents of Wahyul, Ayum and Seogwipo groundwater were concentrated into 58.6, 118.9, and 165.1 ppb, respectively, by 6 stages treatment at the recovery ratio of 15%. And these concentrated water (vanadium water) did not exceed the permissible drinking water standards.

• Economic and Environmental Geology
• /
• v.35 no.1
• /
• pp.75-95
• /
• 2002

The Andong pluton in the Andong Batholith is composed of comagmatic plutonic rocks, in which the lithofacies comprise hornblende biotite tonalite in the central paft biotite granodiorite in the marginal paft and porphyritic biotite granite at the topside (noJthea~tern paft) of the pluton. The pluton is petrographically and petrochemically zoned, having more mafic center than margin and topside. Distribution pallern of the lithofacies represents a reverse zoning in the pluton. Modal and chemical data in the pluton show progressive and gradual compositional variations from the centrer via the margin to the topside. Quartz and K-teldspar increase toward the topside of the pluton, whereas hornblende, biotite and color index increase toward the center. The bulk composition in the pluton is also reversely zoned, with high $Si0_2$ and $K_{2}O$ in the topside facies, and high MnO, CaO, $Ti0_2$, $Fe_{2}O_{3}$t, MgO and $P_{2}O_{5}$ in the central facies. The reverse zoning is also evident in higher Cr. V, Ni, Sc and Sr of the more mafic tonalite in the interior. The reversely zoned pluton results from remobilization (resurgence) of the lower more mafic compositional zone into the upper more felsic zones of the pluton modified by thennogravitational diffusion and fractional crystallization. In the initial stages of evolution, the pluton was a petrochemical system that fonned chemical compositional zonation with mafic tonalitic magma in the lower. granodioritic one in the middle and granitic one in the upper paft of the magma chamber. Periodic influxes of more mafic magma from the ba~e resulted in mingling of liquids and redistribution of minerals, and may have triggered the remobilil.ation of the lower compositional zone into the upper more felsic zones.

• Journal of the Korean Chemical Society
• /
• v.38 no.8
• /
• pp.547-551
• /
• 1994

A series of samples in the $Nd_{1-x}Ba_xFeO_{3-y}$ system has been prepared by heating the reactants to$1200^{\circ}C$ under an ambient atmosphere, and the solid solutions were identified by X-ray power diffraction analysis. The crystal systems of samples with x = 0.00 and 0.25 were found to be orthorhombic whose local symmetry is similiar to the distorted octahedral with orthoferrite type one, whereas those with x = 0.50 and 0.75 to be the cubic system. Since Fe ions in the solid solutions are a mixed valence state between $Fe^{3+}\;and\;Fe^{4+}$ ions, the nonstoichiometric chemical formulas could be determined from the mole ratio of $Fe^{4+}$ ion and oxygen vacacies. According to the Mossbauer spectroscopic analysis, the presence of 5-coordinated $FeO_5$ was evidenced only in the barium compounds along with $FeO_6,\;and\;FeO_4$, but not in the strontium and calcium compounds. The samples with x = 0.25 and 0.50 show a spectrum of superparamagnetism, which might be due to the formation of a domain of the ferromagnetic interaction between the $Fe^{3+}\;and\;Fe^{4+}$ ions. The electrical conductivities of all samples are within semiconducting range. Since the $Fe^{4+}$ ion acts as an electron acceptor level during the electron transfer between the Fe through intermediate $O^{2-}$ ions, the activation energy of the compounds decreases with the increment of $Fe^{4+}$ content.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.4
• /
• pp.1-5
• /
• 2019

We investigated the effect of Fe₃O₄ addition on the critical temperature of (Bi, Pb)-2223 polycrystalline samples. Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ + x wt. % Fe₃O₄ (x = 0.0, 0.2, 0.4, 0.6, and 0.8) samples were prepared by using a solid-state reaction method. The analysis of X-ray diffraction data indicates that as Fe₃O₄ is added, dominant phase of the sample changes from Bi-2223 to Bi-2212 with an increasing Bi-2201 phase. The transition temperature of the samples drastically decreased with the Fe₃O₄ addition. The resistance data of samples with x = 0.2 and 0.4 showed a double transition indicating a coexistence of Bi-2223 and Bi-2212 phase while the samples with x = 0.6 and 0.8 showed a single transition with a semiconducting behavior. This phase transition may originate from changes in local structure of the Bi-2223 system by Fe₃O₄ addition. Analysis of the pair distribution function of the Cu-O pair in the CuO₂ plane calculated from extended X-ray absorption fine structure data revealed that the oxygen coordination of copper ion changes from CuO₄ planar type (x = 0.0 - 0.4) to CuO₅ pyramidal type (x = 0.6, 0.8). The correlated Debye-Waller factor, providing information on the atomic disorder within the CuO₂ plane, shows an inverse relation to the coordination number. These results indicate that addition of Fe₃O₄ changes the oxygen distribution around Cu in the CuO₂ plane, causing a phase transition from Bi-2223 to more stable Bi-2212/Bi-2201 phases.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.11
• /
• pp.2691-2696
• /
• 2009

Effects of representative group II and transition metal ions on the stability of the $poly(dA){\cdot}[poly(dT)]_2$ triplex were investigated by the van’t Hoff plot constructed from a thermal melting curve. The transition, $poly(dA){\cdot}[poly(dT)]_2\;{\rightarrow}\;poly(dA){\cdot}poly(dT)\;+\;poly(dT)$, was non-spontaneous with a positive Gibb’s free energy, endothermic (${\Delta}H^{\circ}$ > 0), and had a favorable entropy change (${\Delta}S^{\circ}$ > 0), as seen from the negative slope and positive y-intercept in the van’t Hoff plot. Therefore, the transition is driven by entropy change. The $Mg^{2+}$ ion was the most effective at stabilization of the triplex, with the effect decreasing in the order of $Mg^{2+}\;>\;Ca^{2+}\;>\;Sr^{2+}\;>\;Ba^{2+}$. A similar stabilization effect was found for the duplex to single strand transition: $poly(dA){\cdot}poly(dT)\;+\;poly(dT)\;→\;poly(dA)\;+\;2poly(dT)$, with a larger positive free energy. The transition metal ions, namely $Ni_{2+},\;Cu_{2+},\;and\;Zn_{2+}$, did not exhibit any effect on triplex stabilization, while showing little effect on duplex stabilization. The different effects on triplex stabilization between group II metal ions and the transition metal ions may be attributed to their difference in binding to DNA; transition metals are known to coordinate with DNA components, including phosphate groups, while group II metal ions conceivably bind DNA via electrostatic interactions. The $Cd_{2+}$ ion was an exception, effectively stabilizing the triplex and melting temperature of the third strand dissociation was higher than that observed in the presence of $Mg_{2+}$, even though it is in the same group with $Zn_{2+}$. The detailed behavior of the $Cd_{2+}$ ion is currently under investigation.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.1 s.119
• /
• pp.16-24
• /
• 2007

This study was performed to investigate the reaction between alkylketene dimer(AKD) and cellulose molecules in AKD-sized paper sheet. AKD was added to highly beaten($80{\pm}3^{\circ}SR$) SwBKP(ca. 0.8% on pulp) in order to have much AKD retention in the paper sheet. This AKD-sized paper sheet was aged at different temperatures, $60^{\circ}C,\;80^{\circ}C,\;105^{\circ}C\;and\;125^{\circ}C$. Changes in FT-IR spectra of AKD in paper sheet during the ageing were measured. In addition, sizing degrees of the AKD-sized paper sheet pretreated for 30 sec. at $105^{\circ}C$ were measured by HST size tester during the storage at different temperature. IR spectra of AKD-sized paper sheet preheated at $105^{\circ}C$ for 30 sec. showed unchanged spectra two absorption bands at $1849cm^{-1}\;and\;1722cm^{-1}$ which refer to the typical AKD IR bands. However, these typical AKD bands were gradually reduced with increasing ageing, completely disappeared after 6 hrs. and formed new absorption band at $1706cm^{-1}$, which refers to carbonyl stretching vibration of dialkylktone. Eventually the AKD molecule was hydrolyzed to diakylketone without formation of ${\beta}$-ketoester with cellulose in paper sheet. After 6 days ageing, a little amount of ${\beta}$-ketoester bands was identified in 6 or 7 days ageing, because of the absence of water due to long-term heating. The same tendency was observed at different ageing conditions. At the practical papermaking process, AKD reacts prevailing with water, and mostly seems to be hydrolyzed to dialkylketene. Concerned to the sizing development, AKD-sized paper sheet was shown no sizing development at the initial stage of ageing at $60^{\circ}C$ after heating treatment at $105^{\circ}C$ for 30 sec., and gradually increased the sizing degree with increasing ageing, such as Hercules Sizing Tester (HST) 130 see for 12 hr, HST 300 sec. for 3 days and HST 400 sec. for 5 days. It was concluded that hydrolyzed AKD could contributed to the sizing development of the paper sheet.

• Korean Journal of Food Science and Technology
• /
• v.34 no.4
• /
• pp.565-569
• /
• 2002

This study was carried out to estimate the effects of preservatives (alcohol, adipic acid) and heat treatment $(40^{\circ}C,\;60^{\circ}C)$ for the prolongation of shelf-life on low-salt Kimchi. Low-salt Kimchi was prepared with salt replacements (NaCl 50%, KCl 36%, $MgSO_4$ 10%, $CaSO_4$ 3%, glutamic acid 0.2%). Chemical characteristics and microbiological parameters were monitored during fermentation at $20^{\circ}C$. When three kinds of preservative which were alcohol 2.0%, adipic acid 0.1% and their mixture were added to low-salt Kimchi, shelf-life of them were prolonged. To extend the shelf-life of low-salt Kimchi, when the heat treatment at $40^{\circ}C$ and $60^{\circ}C$ were tried, heat treatment at $60^{\circ}C$ was superior than at $40^{\circ}C$. In sensory evaluation of low-salt Kimchi, the control was showed the best quality in the overall acceptability. And low-salt Kimchi treated at $40^{\circ}C$ showed the most similar characteristics to the control Kimchi.