• Journal of the Korean Wood Science and Technology
• /
• v.47 no.1
• /
• pp.21-32
• /
• 2019

In order to investigate the decay process of wood treated with preservative, waterproofing agent and their compound systems, a full-cell process was applied to impregnate the sapwood of poplar (Populus cathay) at paraffin wax emulsion concentrations of 0.5% and 2.0%, Copper Azole (CA) concentrations of 0.3% and 0.5%, and their four compound systems, respectively. Leaching tests and laboratory decay resistance against the white-rot fungus Corious versicolor (L.) Murrill for treated wood were carried out according to the America Standard E11-06 and China Standard GB/T 13942.1-2009. At certain time intervals during the decay test, samples were characterized by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction technique (XRD) to investigate the time-dependent changes of chemical components and crystalline structure, thus clarifying the decay mechanisms. The results suggested that white-rot fungi degrade hemicellulose and lignin in the wood cell wall first, followed by a simultaneous degradation of polysaccharides and lignin. Besides, CA could not only slower the decomposition of both hemicellulose and lignin, but also reduce the degradation amount of hemicellulose. However, paraffin wax emulsion at high concentration had a negative effect on the impregnation of CA for the compound system treated wood.

• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.185-194
• /
• 1998

Flow-induced voids during resin impregnation and poor fiber wetting give serious effects on the mechanical properties of composites in resin transfer molding process. In order to better understand the characteristics of resin flow and to investigate the mechanism of void formation, flow visualization experiment for the resin impregnation was carried out on plain weaving glass fiber mats using silicon oils with various viscosity values. The permeability and the capillary pressure for the fiber mats of different porosities were obtained by measuring the penetration length of the resin with time and with various injection pressure. At low porosity and low operating pressure, the capillary pressure played a significant role in impregnation process. Video-assisted microscopy was used in taking the magnified photograph of the flow front of the resin to investigate the effect of the capillary pressure on the void formation. The results showed that the voids were formed easily when the capillary pressure was relatively high. No voids were detected above the critical capillary number of 2.75$\times$$10^{-3}, and below the critical number the void content increased exponentially with decrease of the capillary number. The content of void formed was independent of the viscosity of the resin. For a given capillary number, the void content reduced with the lower porosity of the fiber mat.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.4
• /
• pp.435-441
• /
• 2017

Studies on self-healing have currently been diversified and the methods to evaluate the studies have become more diversified as well. Among them, the back-scattered electron (BSE) image acquired through the scanning electron microscope (SEM) is attempted as the means to evaluate the self-healing effect on cracks. In order evaluate by the BSE image, sophisticated pre-processing of specimen is critical and this injected inside the particle, pore and artificial crack of the hardener to stabilize the structure of the newly generated self-healing product and it enables to endure the stress on polishing without deformation. The impregnated specimen smoothen the surface to obtain the BSE image of high resolution that polishing is made for diamond suspension for wet polishing after dry polishing. As a result of evaluating the self-healing product on the impregnated and polished self-healing specimen, the generated product is formed from the surface of the artificial crack and the self-healing substances are confirmed as $Ca(OH)_2$ and C-S-H.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.126-132
• /
• 2001

This research is carried out to investigate the formation and preservative effectiveness of inorganic substance, calcium carbonate($CaCO_3$), in wood. The specimens were prepared by the impregnation with saturated solutions of potassium carbonate($K_2CO_3$) into the wood followed by precipitation in saturated solutions of calcium chloride($CaCl_2$) for 24h, 72h and 120h, and then they were leached in instrument flowing with water for 24h. The weight percent gains of $K_2CO_3$ solution impregnated specimens reached approximately a maximum value (108.1%) by 72h precipitation in $CaCl_2$ solutions. Inorganic substances were observed to he produced in the lumina of tracheids of specimens. From these inorganic substances filling in the tracheids, characteristic X-rays of calcium(Ca-$K_{\alpha}$) were detected by energy dispersive X-ray analyzer. Moreover, it was shown from a leaching treatment that these substances could not he leached easily from the specimens. Therefore, they were could he considered to be insoluble calcium carbonates. The weight losses of the prepared specimens were hardly occurred by test fungi attacks. Thus inorganic substances in specimens can be said to have preservative effectiveness.

• Applied Chemistry for Engineering
• /
• v.23 no.6
• /
• pp.604-607
• /
• 2012

Solid base catalysts for biodiesel production were synthesized by impregnating basic metal species on two support materials with large specific surface area : zeolite and pyrolysis char. KL zeolite and Undaria pinnatifida char were impregnated with KOH aqueous solution and calcium nitrate solution, respectively, to enhance the basic strength. The catalysts synthesized were characterized using Hammett indicators and $CO_2$-TPD analysis. Biodiesel was produced using soybean oil and methanol over the catalysts synthesized. The content of fatty acid methyl esters was measured to evaluate the catalytic activity. Generally, the catalytic activity increased with increasing quantity of basic metal impregnated but impregnation of excessive amount of metal could cause reduction in the activity.

• Membrane Journal
• /
• v.11 no.2
• /
• pp.89-95
• /
• 2001

Polysulfone membranes containing an inorganic fluor, cerium activated yttrium silicate (CA Y5), were prepared via the phase inversion technique. The casting solutions with the fluor' were solidified to result in a membrane by using two different nonsolvent coagulants, water and isopropanol. In the process, the fluor worked as a monitioring agent for investigating the characteristics of the phase inversiun process. On the initial contact with water as nonsolvent, the induction of rapid polymer collapse results.in the entrapment of the fluor in the formed membrane structure. Impregnated fluor is dispersed in the polymer structure rather than being enveloped by polymer molecules. In comparison, the fluor is localized in the cell-like structure of membrane, as the cast solution film is cuagulated by immersion into a isopropanol bath.

• The Journal of Engineering Research
• /
• v.3 no.1
• /
• pp.189-197
• /
• 1998

Hyeroxyapatite(HAp) which has good biocompatibility was made by Wet Chemical Process. The surface of Ti-6Al-4V, coated with HAp by lon Beam Assisted Deposition (IBAD), was treated with 5ppm, 10ppm, 20ppm, and 100ppm of $AgNO_3$ solution. In this Ag impregnation process, $Ca^{2+}$ of HAp was substituted with $Ag^+$ of $AgNO_3$. In this study, the antimicrobial effect and biocompatibility of Ti-6Al-4V alloy which was coated with Ag-HAp were examined. The antimicrobial test was carried out with two kinds of bacteria(P. Aeruginosa, S. Epidermidis), which are highly infectious in a transplanting operation of implant materials. As a result of the test, it was observed that Ti-6Al-4V alloy which was treated by 20ppm of $AgNO_3$ solution has good biocompatibility. In order to observe the antimicrobial mechanism of $Ag^+$, E. coli which is the most common bacterium was treated by Ag-HAp. Then cell morphology of E. coli was observed by the transmission electron microscope(TEM). The destruction of cell wall and cytoplasm of E. coil were observed. A black spot appeared in the cytoplasm was analyzed by energy dispersive analysis X-ray (EDAX) and it showed a small amount of $Ag^+$. Thus, it was proved that $Ag^+$ destroys bacteria effectively and Ti-6Al-4V alloy which was impregnate with Ag ion show antimicrobial effect on infection bacteria.

• Carbon letters
• /
• v.28
• /
• pp.72-80
• /
• 2018

In this study, an empirical relationship between the energy band gap of multi-walled carbon nanotubes (MWCNTs) and synthesis parameters in a chemical vapor deposition (CVD) reactor using factorial design of experiment was established. A bimetallic (Fe-Ni) catalyst supported on $CaCO_3$ was synthesized via wet impregnation technique and used for MWCNT growth. The effects of synthesis parameters such as temperature, time, acetylene flow rate, and argon carrier gas flow rate on the MWCNTs energy gap, yield, and aspect ratio were investigated. The as-prepared supported bimetallic catalyst and the MWCNTs were characterized for their morphologies, microstructures, elemental composition, thermal profiles and surface areas by high-resolution scanning electron microscope, high resolution transmission electron microscope, energy dispersive X-ray spectroscopy, thermal gravimetry analysis and Brunauer-Emmett-Teller. A regression model was developed to establish the relationship between band gap energy, MWCNTs yield and aspect ratio. The results revealed that the optimum conditions to obtain high yield and quality MWCNTs of 159.9% were: temperature ($700^{\circ}C$), time (55 min), argon flow rate ($230.37mL\;min^{-1}$) and acetylene flow rate ($150mL\;min^{-1}$) respectively. The developed regression models demonstrated that the estimated values for the three response variables; energy gap, yield and aspect ratio, were 0.246 eV, 557.64 and 0.82. The regression models showed that the energy band gap, yield, and aspect ratio of the MWCNTs were largely influenced by the synthesis parameters and can be controlled in a CVD reactor.

• Journal of Conservation Science
• /
• v.18 s.18
• /
• pp.89-96
• /
• 2006

Surface layers of stone cultural properties including the soluble salt need consolidation because they are mostly very weak. There is a lot of research on the penetration depth of consolidant in stone and the effect of consolidant on mechanical stability of deteriorated structure. But some conservation experiences show that consolidation with silicic acid ester is not successful on salt contaminated stone cultural properties. In this study, in order to assess the influence of soluble salts$(CaSO_4\;2H_2O,\;NaNO_3)$ on the efficiency of consolidation on the deteriorated stone cultural properties(Nationalgalerie, Berlin, Germany) sandstone samples have been soaked with the salts solution. The impregnation of consolidant based on ethyl filicate have been afterwards carried out on these samples. As a result, it confirms that the soluble salts act as a preventer or consolidation. They fill up the pores in the stone and prevent that sufficient amount of consolidant enter deeply into the stone. According to this result, if use silicic ethyl ester as a consolidant for the research object which is built by Nebra sandstone, desalination is necessary before the treatment with consolidant. But it is also reported by other researches that some soluble salts improve the consolidation effect. Therefore it should be necessary to pre-study about salt and its harmfulness before the consolidation treatment. In order to consolidate without the aggravative damage in salt contaminated stone cultural heritage, we must first of all study the relations among salt, stone and consolidant.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.1
• /
• pp.36-42
• /
• 1997

The fiber wall filling(FWF) technology, which is based on Precipitatin of fillers in the micropores of the cell wall structure of never-dried chemical pulp fiber, has been developed to improve filling and loading process in papermaking. In presenting FWF technique here, micropores of pulp fiber are first impregnated with an ionic solution of water soluble salt and consecutively impregnated with the second salt solution. This procedure generates an insoluble precipitate within the micropores of cell wall by chemical interaction of these two ionic salt solutions This is the first attempts to use FWF technology for the quality of waste paper grade which is recycled in papermaking, even though this FWF technology has been impressively improved for never-dried chemical pulp in filling and loading process of papermaking. The precipitated amount of CaCO$_3$ and SrCO$_3$ reached 5-6% and 4-5% of the waste paper weight respectively, which was measured by ash content of the burned waste paper fiber. On the other way the precipitated amounts of those materials impregnated into never-dried chemical pulp fiber have reached 17-18% and 16-18% respectively. The micropore loading technique gives optical and physical properties to the handsheets formed with celt-wall-filled fibers which are better than those handsheet properties resulting from conventional loading. The papers made from the cell-wall-filled pulps are stronger than those with the customary location of filler between the fibers.