• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.49-53
• /
• 1985

The effects of pre-treatments, the hot water extraction of wood meal and the addition of chemical ($CaCl_2$) to wood-cement water system on the properties of wood-cement composite such as modulus of rupture (MOR), modulus of elasticity (MOE), water sorption ratio and swelling ratio of resulting boards were studied in this experiment. The wood meals through 0.83mm(20 mesh) and retained on 0.42mm(35 mesh) screen were prepared from Pinus densiflora S. at Z. and Larix leptolepsis G. For hot water extraction, 500 grams of wood meal for each species were heated to boiling with 1,500ml of distilled water in 2-liter beaker for 6 hours. Every 2 hours, the wood meals were washed with boiling distil1ed water and reheated to boiling again. After 6 hours boiling, the boiled wood particles were collected by pouring this particles on 200 mesh screen. The collected particles then washed twice with hot distilled water and dried for 24 hours in an oven at $109{\pm}20^{\circ}C$. A mixture of 663.4 grams of cement with 331.7 grams of wood meal based on oven-dry weight were dry-mixed in a plastic vessel. The mixture was kneaded with 497.6ml of distilled water in the ratio of 1.5ml of water to a gram of wood meal. To add calcium chloride to the mixture as an accelerator, $CaCl_2$ 4% solution by weight per volume, was added to pine-or larch-cement board in the ratio of 3% to cement weight. To set wood-cement board, this mixture was clamped at 30cm ${\times}$ 30cm, in thickness of 1.5cm for 3 days at room temperature, declamped and then placed at open condition for 17 days. The target density was 1.0. The four specimens sized to 5cm in width and 28cm in length were used for MOR and MOE test for each treatment. After MOR test, the tested specimens were cut to the size of 5cm ${\times}$ 5cm for water sorption and swelling test. The twenty specimens used to measure the water sorption ratio (soaking 24 hours) and ten of these were used for swelling ratio measurement The results obtained were as follows: 1) Larch was not suitable for wood-cement boards because larch-cement board developed no strength, but pine showed 97.9kg/$cm^2$ by hot water extraction. 2) To increase MOR, hot water extraction was more effective than the addition of $CaCl_2$ in pine and larch because the $CaCl_2$ addition was seemed to speed up the ratio of cement hydration without reacting with the wood substances. 3) The water sorption ratio was lowered by the addition of $CaCl_2$ to wood-cement system because the chemical additive accelerated the rate of cement hydration. 4) In pine-cement board, the swelling ratio from 0.37 to 0.42 percent was observed in length and the swelling ratio from 0.88 to 2.0 percent in thickness. As a rule, the swelling ratio of wood-cement board was very low and the swelling ratio in thickness was higher than in length.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.75-76
• /
• 2018

MiDF, Micro Defect Free concrete, is the concrete made for high strength development by minimizing the defects such as micro pore and ITZ. Since MiDF exhibits strength through hydro-thermal synthesis reaction, it is essential to select the optimum C/S mole ratio. In this study, the basic characteristics of MiDF were evaluated by controlling the C/S mole ratio by SF and QP.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.2
• /
• pp.719-722
• /
• 2015

Objective: To evaluate the values of 4 tumor markers in serum and ascites and their ascites/serum ratios in the identification and diagnosis of benign and malignant ascites. Materials and Methods: A total of 76 patients were selected as subjects and divided into malignant ascites group (45 cases) and benign ascites group (31 cases). Samples of ascites and serum of all hospitalized patients were collected before treatment. The levels of carcinoembryonic antigen (CEA), alpha fetoprotein (AFP), cancer antigen 125 (CA125) and carbohydrate antigen 19-9 (CA19-9) were detected by chemiluminescence (CLIA). Results: CEA, AFP and CA19-9 in both serum and ascites as well as CA125 in ascites were evidently higher in the malignant ascites group than in the benign ascites group (P<0.01). Malignant ascites was associated with elevated ascites/serum ratios for AFP and CA125 (P<0.01). The areas under receiver operating characteristic (AUROCs) of CEA and CA125 in ascites and the ratios of ascites/serum of AFP, CEA, CA125 and CA19-9 were all >0.7, suggesting certain values, while those of ascites CA19-9 and serum CEA were 0.697 and 0.629 respectively, indicating low accuracy in the identification and diagnosis of benign and malignant ascites. However, the AUROCs of the remaining indexes were <0.5, with no value for identification and diagnosis. Compared with single index, the sensitivity of combined detection increased significantly (P<0.05), in which the combined detection of CEA, CA19-9 and CA125 in ascites as well as the ratio of ascites/serum of CEA, CA19-9, CA125 and AFP had the highest sensitivity (98.4%) but with relevantly low specificity. Both sensitivity and specificity of combined detection should be comprehensively considered so as to choose the most appropriate index. Conclusions: Compared with single index, combined detection of tumor markers in serum and ascites can significantly improve the diagnostic sensitivity and specificity.

• The Korean Journal of Physiology and Pharmacology
• /
• v.9 no.6
• /
• pp.341-346
• /
• 2005

The mechanism underlying oxidant-induced intracellular $Ca^{2+}$ ($[Ca^{2+}]_i$) increase was studied in cultured bovine aortic endothelial cells (BAECs) using fura-2 AM. In the presence of 2 mM extracellular $Ca^{2+}$, the application of DTBNP ($20{\mu}M$), a membrane-permeable oxidant, caused an increase in $[Ca^{2+}]_i$, and DTT (2 mM) as a reductant completely reversed the effect of DTBNP. The $[Ca^{2+}]_i$ increase induced by DTBNP was also observed in an extracellular $Ca^{2+}$-free/2 mM EGTA solution, indicating the release of $Ca^{2+}$ from intracellular store(s). After endoplasmic reticulum was depleted by an $IP_3$-generating agonist, ATP ($30{\mu}M$) or an ER $Ca^{2+}$ pump inhibitor, thapsigargin ($1{\mu}M$), DTBNP-stressed BAECs showed an increase of $[Ca^{2+}]_i$ in $Ca^{2+}$-free/2 mM EGTA solution. Ratio-differences before and after the application of DTBNP after pretreatment with ATP or thapsigargin were $0.42{\pm}0.15$ and $0.49{\pm}0.07$, respectively (n=7), which are significantly reduced, compared to the control value of $0.72{\pm}0.07$ in a $Ca^{2+}$-free/2 mM EGTA solution. After the protonophore CCCP ($10{\mu}M$) challenge to release mitochondrial $Ca^{2+}$, the similar result was obtained. Ratio-difference before and after the application of DTBNP after pretreatment with CCCP was $0.46{\pm}0.09$ (n=7). Simultaneous application of thapsigargin and CCCP completely abolished the DTBNP-induced $[Ca^{2+}]_i$ increase. The above results together indicate that the increase of $[Ca^{2+}]_i$ by DTBNP resulted from the release of $Ca^{2+}$ from both endoplasmic reticulum and mitochondria.

• Journal of Soil and Groundwater Environment
• /
• v.20 no.7
• /
• pp.103-111
• /
• 2015

Soil washing with ethylenediaminetetraacetic acid (EDTA) is highly effective in the remediation of soils contaminated with heavy metals. The EDTA recycling process is a requisite for reducing the operating cost. The applicability of Na₂S addition on the precipitation of heavy metals from the spent soil washing solution and thereby recycling of EDTA was investigated. Addition of Na₂S into the single metal-EDTA and the mixed metal-EDTA solutions ([Na₂S]/[metal-EDTA] ratio = 30, reaction time = 30 min and pH = 7~9) was highly effective in the separation of Cu and Pb from metal-EDTA complexes, but not for Ni. The Zn removal efficiency varied with pH and slightly increased upto 40% as the reaction time increased from 0 to 240 min which was longer than those for Cu and Pb. Ca(OH)₂ was subsequently added to induce further precipitation of Zn and Ni and to reduce the Na₂S dose. At the [Na₂S]/[metal-EDTA] ratio of 10, the removal efficiencies of all heavy metals excluding Ni were above 98% with the dose of Ca(OH)₂ at 0.002, 0.006 and 0.008 g into 100 mL of Cu-, Pb- and Zn-EDTA solutions, respectively. However, Ca(OH)₂ addition was not effective for Ni-EDTA solution. A further research is needed to improve metal removal efficiency and subsequent EDTA recycling for the real application in field-contaminated soils.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.179-182
• /
• 2007

The compressive fatigue tests on the closed cell Al-Si-Ca alloy foams with two different thicknesses were performed using a load ratio of 0.1. The quasi-static and cyclic compressive behaviors were obtained respectively. The fatigue stress-life (S-N) curves were evaluated from the obtained cyclic compressive behaviors. S-N curves were presented for the onset of progressive shortening. It turned out that the fatigue strength showed higher value for the thicker foam and the onset of shortening of thinner foam took place earlier. The crushing was found to initiate in a single band which broadens gradually with additional fatigue cycles. Progressive shortening of the specimen took place due to a combination of low cycle fatigue failure and cyclic ratcheting.

• Environmental Engineering Research
• /
• v.11 no.1
• /
• pp.54-61
• /
• 2006

An electron probe microanalysis (EPMA) investigation can provide quantitative and qualitative insight into the nature of the surface and bulk chemistry on solidified waste forms(SWF). The proportion of Pb in grain areas is below 0.3 wt. %, and the proportion near the border of the grain slightly increases to 0.98 wt. % but in the inter-particle areas farther from the grain, the concentration of Pb markedly increases. It is apparent that very little Pb diffuses into the tricalcium silicate($C_3S$) particles and most of the Pb exists as precipitates of sulfate, hydroxide, and carbonate in the cavity areas between $C_3S$ grains. Calcite additions on Pb-doped SWF are also observed to induce deeper incorporation of lead into the cement grains with EPMA line-analysis of cross-sections of cement grains. The line-analysis reveals the presence of $0.2{\sim}5$ weight % Pb over $5\;{\mu}m$ from cement grain boundaries. In the inter-particle areas, the ratio of Ca, Si, Al and S to Pb is relatively similar even at some distance from the grain border and the Pb (wt. %) ratio is reasonably constant throughout the whole inter-particles area. It is apparent that the enhanced development of C-S-H on addition of calcite can increasingly absorbs lead species within the silica matrix.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.147-156
• /
• 1989

The effects of starting composition, sintering temperature and porosity on the mechanical properties of hydroxyapatite ceramics were investigated. The hydroxyapatite powder were prepared by precipitation method using Ca(NO3)2.4H2O and (NH4)2.HPO4. The obtained powders were Ca-deficient hydroxyapatites and as the Ca/P mole ration in the initial solution was increased, the particle size of the precipitates was decreased, and the decomposition of hydroxyapatite to $\beta$-TCP was controlled. The porosity, as well as Ca/P mole ratio in starting composition and sintering temperature, plays major role in the mechanical properties of dense hydroxyapatite ceramics.

• Journal of the East Asian Society of Dietary Life
• /
• v.15 no.5
• /
• pp.524-530
• /
• 2005

Dietary effect of soyfiber beni-koji (SBK) with chitosan-ascorbate (CA) on the level of serum lipids in rats fed a high fat diet was investigated The experimental groups which were divided into high fat diet control group(HC-group), $2\%\;SBK+0.1\%$ CA mixture diet group(CA1-group), $2\%\;SBK+0.15\%$ CA mixture diet group(CA2-group), and $2\%\;SBK+0.2\%$ CA mixture diet group (CA2-group) were fed for 4 weeks. Weight gains in CA2- and CA3-group were $5.3\%\;and\;9.5\%$ lower than that of HC-group, respectively, while there was no significant difference in feed intakes, feed efficiency ratio and organs weight Level of serum triglyceride in $C_3-group\;was\;21\%$ lower than that of HC-group. Level of serum total cholesterol and LDL-cholesterol in CA2- and CA3-group were $22.1\~22.7\%\;and\;58.6\~64.3\%$ lower than those of HC-group, respectively. Atherogenic index decreased with the higher level of CA. Level of lipid peroxide in CA3-group was $24\%$ lower than that of HC-group, while there was no significant difference in GSH(Glutathione-S-transferase) content O type activities of XOD(xanthine oxidase) in the treated groups were lower, especially the activity in CA3-group was $51.6\%$ lower than that of HC-group. Also, O/T ratio of XOD was lower, showing $21.7\~23.5\%$ in treated groups and $34.0\%$ in HC-group(p<0.05). GST activities were 332.52 units in HC-group and $350.28\~355.63$ units in the treated groups, but there were no significant differences among them.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.5
• /
• pp.563-571
• /
• 2021

In this study, calcium alginate based cation exchange membrane was prepared and used to develop membrane capacitive deionization (MCDI) system for effective hardness control. As a major result, the MCDI with Ca-alginate membrane showed 27% better deionization capacity than the MCDI with a commercial cation exchange membrane. This superior improvement in the deionization capacity was expected to be due to the high ratio of transport number/electrical resistance (S_c/R_ratio) of Ca-alginate membrane. In addition, the MCDI with Ca-alginate membrane showed better deionization performance than the MCDI with Ca-alginate coating. This was because the space between the electrode and the Ca-alginate membrane was utilized for ion adsorption. The preliminary results indicated that the MCDI with Ca-alginate membrane can be a viable technique for the hardness control.