• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.41-48
• /
• 2010

Uranium deposits from an electrorefining process contain about 30% salt. In order to recover pure uranium and transform it into an ingot, the salts have to be removed from the uranium deposits. Major process variables for the salt distillation process of the uranium deposits are hold temperature and vacuum pressure. Effects of the variables on the salt removal efficiency were studied in the previous study[1]. By applying the Hertz-Langmuir relation to the salt evaporation of the uranium deposits, the evaporation coefficients were obtained at the various conditions. The operational conditions for achieving above 99% salt removal were deduced. The salt distilled uranium deposits tend to form the eutectic melt with iron, nickel, chromium for structural material of salt evaporator. In this study, we investigated the hold temperature limitation in order to prevent the formation of the eutetic melt between urnaium and other metals. The reactions between the uranium metal and stainless steel were tested at various conditions. And for enhancing the evaporation rate of the salt and the efficient recovery of the distilled salt, the thermal analysis of the salt distiller was conducted by using commercial CFX software. From the thermal analysis, the effect of Ar gas flow on the evaporation of the salt was studied.

• Membrane Journal
• /
• v.31 no.6
• /
• pp.417-425
• /
• 2021

As the demand for high-capacity batteries increases, there has been growing researches on the lithium metal anode with a capacity (3,860 mAh/g) of higher than that of conventional one and a low electrochemical potential (-3.040 V). In this study, using the anatase phased TiO₂ nanoparticles synthesized by hydrothermal synthesis, a PVdF-HFP/TiO₂ organic/inorganic composite material was designed and used as an interfacial protective layer for a Li metal anode. As-formed organic/inorganic-lithium composite thin film was confirmed through the crystalline structure and morphological analyses. In addition, the electrochemical test (cycle stability and voltage profile) confirmed that the protective layer of PVdF-HFP/TiO₂ composite (10 wt% TiO₂ and 1.1 ㎛ film thickness) contributed to the enhanced electrochemical performance of the lithium metal anode (Colombic efficiency retention: 90% for 77 cycles). Based on comparative test with the untreated lithium electrode, it was confirmed that our protective layer plays an important role to stabilize/improve the EC performance of the lithium metal negative electrode.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.4
• /
• pp.317-324
• /
• 2024

We demonstrate a direct growth of carbon nanotubes (CNTs) on the surface of LiFePO₄ (LFP) powders for use in lithium-ion batteries (LIB). LFP has been widely used as a cathode material due to its low cost and high stability. However, there is a still enough room for development to overcome its low energy density and electrical conductivity. In this study, we fabricated novel structured composites of LFP and CNTs (LFP-CNTs) and characterized the electrochemical properties of LIB. The composites were prepared by direct growth of CNTs on the surface of LFP using a rotary chemical vapor deposition. The growth temperature and rotation speed of the chamber were optimized at 600 ℃ and 5 rpm, respectively. For the LIB cell fabrication, a half-cell was fabricated using polytetrafluoroethylene (PTFE) and carbon black as binder and conductive additives, respectively. The electrochemical properties of LIBs using commercial carbon-coated LFP (LFP/C), LFP with CNTs grown for 10 (LFP/CNTs-10m) and 30 min(LFP/CNTs-30m) are comparatively investigated. For example, after the formation cycle, we obtained 149.3, 160.1, and 175.0 mAh/g for LFP/C, LFP/CNTs-10m, and LFP/CNTs-30m, respectively. In addition, the improved rate performance and 111.9 mAh/g capacity at 2C rate were achieved from the LFP/CNTs-30m sample compared to the LFP/CNTs-10m and LFP/C samples. We believe that the approach using direct growth of CNTs on LFP particles provides straightforward solution to improve the conductivity in the LFP-based electrode by constructing conduction pathways.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.945-953
• /
• 2006

The researchers in the field of cognitive science and learning science suggest that the teaching activity induces the elaborative and meaningful learning. Actually, lots of research findings have shown the beneficial effect of learning by teaching such as peer tutoring. But peer tutoring has some limitations in the practical learning context. To overcome some limitations, the new concept of "learning by teaching" through the agent called Teachable Agent. The teachable agent is a modified version of traditional intelligent tutoring system that assigns a role of tutor to teach the agent. The teachable agent monitors individual difference and provides a student with a chance for deep learning and motivation to learn by allowing them to play an active role in the process of learning. That is, The teaching activity induces the elaborative and meaningful learning. This study compared the effects of our teachable agent, KORI, and peer tutoring on the cognition and motivation. The field experiment was conducted to examine whether learning by teaching the teachable agent would be more effective than peer tutoring and reading condition. In the experiment, all participants took 30 minutes lesson on rock and rock cycle together to acquire the base knowledge in the domain. After the lesson, participants were randomly assigned to one of the three experimental conditions; reading condition, peer tutoring condition, and teachable agent condition. Next, participants of each condition moved into separated place and performed their own learning activity. After finishing all of the learning activities in each condition, all participants were instructed to rate the interestingness using a 5-point scale on their own learning activity and leaning material, and were given the comprehension test. The results indicated that the teachable agent condition and the peer tutoring condition showed more interests in the learning than the reading condition. It is suggested that teachable agent has more advantages in overcoming the several practical limitations of peer tutoring such as restrictions in time and place, tutor's cognitive burden, unnecessary interaction during peer tutoring. The applicability and prospects of the teachable agent as an efficient substitute for peer tutoring and traditional intelligent tutoring system were also discussed.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.12 no.3
• /
• pp.179-189
• /
• 2014

Pyroprocessing has been developed for the purpose of resolving the current spent nuclear fuel management issue and enhancing the recycle of valuable resources. An electrolytic reduction of the pyroprocessing is a process to reduce oxides into metals using LiCl as an electrolyte and requires a post-treatment process due to the inclusion of residual salt in porous metal products. A vacuum distillation has been adopted for various molten salt systems and could be applied to the post-treatment process of the electrolytic reduction. The residual salt in the metal products includes LiCl, alkali chlorides, and alkaline earth chlorides. In this paper, vapor pressures of chlorides have been estimated and the composition changes on the residual liquid during the vacuum distillation process have been calculated. A model combining a material balance and vapor-liquid equilibrium relations has been proposed under a constant vapor discharging flow rate and liquid composition changes have been calculated using the vapor pressures with respect to a dimensionless time. The behaviors have been compared with temperature and molten salt composition changes to simulate the process condition variation. The distillation of the residual salt has been dominated by LiCl which is the main component of the salt and CsCl of which vapor pressure is higher than that of LiCl would be readily removed. RbCl exhibits similar vapor pressure with LiCl and maintains its composition. However, $SrCl_2$ and $BaCl_2$ of which vapor pressures are much lower than that of LiCl are concentrated with time and expected to be possibly precipitated during the distillation when the initial compositions are increased.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.1
• /
• pp.22-28
• /
• 2015

The design on a riser in 1MW OTEC system is performed. The minimum diameter of the riser is decided depending on intake quantity of deep-sea water to supply an OTEC cycle. An applicable pipe material is selected from analyzing the properties of commercial pipes. The selected HDPE pipe with the low density and strength is reinforced with a lumped block attached at the end of and wire ropes along the riser. A lumped block, connected to a floating structure by wire ropes, with 25% and 50% weight of a GFRP riser is designed to be attached the end of a riser. The structural safety of the HDPE riser with wire rope supporting axial loads induced by a lumped block is analyzed under the harsh ocean environmental condition near Hawaii ocean with the numerical method. The final dimension of the riser and accessories is determined considering the economic point of view. The designed riser will be applicable to the construction of the 1 MW OTEC pilot plant.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.139-148
• /
• 2011

Asphalt concrete overlay method is used by general maintenance and rehabilitation of construction for aged concrete pavement in Korea. However, in case of the AC overlay method to extend service life of the existing concrete pavements, various distresses of reflection crack, pothole and rutting are the typical problems of the asphalt overlay on existing concrete pavement since it has different physical characteristics between asphalt overlay and existing concrete pavement. To achieve this, application of concrete overlay method is required instead of AC overlay method. Concrete overlay method has advantages that can reduce maintenance cycle and costs since it has excellent bearing value for heavy vehicles and no rutting. However, technical problems of detour road construction, traffic control and other disadvantages happened by long curing time. Thus, in this study and experimental research were launched to evaluate the workability, durability and resistance against environmental loading of Very Rapid Hardening Acrylic Polymer Modified Concrete(VRH-APMC) for application of bonded concrete overlay method. Test results showed that the compressive and bond strength were exceed 21MPa and 1.4MPa of target strength after four hours for rapid traffic opening properties. And tests of resistance against environmental loading results showed that VRH-APMC secured excellent durability. Thus, it was known that VRH-APMC was suitable material for large scale bonded concrete overlay method, and it was possible to use maintenance and rehabilitation method which needs enough workability and rapid traffic opening.

• Journal of Chest Surgery
• /
• v.33 no.8
• /
• pp.662-668
• /
• 2000

Background: Many recent results of clinical trials show that pre-operative concurrent chemoradiotherapy and surgical resection could increase the survival of N2 positive stage IIIA non-small cell lung cancer. This study was performed to assess the feasibility, toxicity, and affect rates of concurrent chemoradiotherapy and surgical resection in N2 positive stage IIIA non-small cell lung cancer. Material and Method: Thirty-one patients who underwent preoperative concurrent chemoradiotherapy for N2 positive stage IIIA non-small-cell lung cancer from May 1997 to April 1999 were entered into the study. Mean age was 61 yrs(43∼70 yrs), There were 24 men and 7 women. The confirmation of N2 disease were achieved through mediastinoscopic biopsy(24) and CT scans(7). Induction was achieved by two cycles of cisplatin and etoposide(EP) plus concurrent chest radiotherapy to 45 Gy. Resections were done at 3 weeks after the complection of preoperative concurrent chemoradiotherapy. Resections were performed in 23 patients, excluding 5 refusals and 3 distant metastasis. Result: All patients were compled the thoracic radiotherapy except one who had distant metastasis. Twenty three patients were completed the planned 2 cycles of EP chemotherapy, and 8 patients were received only 1 cycle for severe side effects(6), refusal(1), and distant metastasis(1). There was one postoperative mortality, and the cause of death was ARDS. Three patients who had neutropenic fever and one patient who had radiation pneumonitis were required admission and treatment. Esophagitis was the most common acute side effect, but relatively well-tolerated in most patients. The complection rate of concurrent chemoradiotherapy was 74%, resection rate was 71%, pathologic complete remission rate was 13.6%, and pathologic down-staging rate was 68%. Conclusion: Morbidity related to each treatment was acceptable and many of the patients have benefited down staging of its disease. Further prospective, preferably randomized, clinical trials of larger scale may be warranted to confirm the actual benefit of preoperative concurrent chemoradiotherapy and surgical resection in N2-positive stage IIIA non-small cell lung cancer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.96-97
• /
• 2012

In nitride and oxide film deposition, sputtered metals react with nitrogen or oxygen gas in a vacuum chamber to form metal nitride or oxide films on a substrate. The physical properties of sputtered films (metals, oxides, and nitrides) are strongly influenced by magnetron plasma density during the deposition process. Typical target power densities on the magnetron during the deposition process are ~ (5-30) W/cm2, which gives a relatively low plasma density. The main challenge in reactive sputtering is the ability to generate a stable, arc free discharge at high plasma densities. Arcs occur due to formation of an insulating layer on the target surface caused by the re-deposition effect. One current method of generating an arc free discharge is to use the commercially available Pinnacle Plus+ Pulsed DC plasma generator manufactured by Advanced Energy Inc. This plasma generator uses a positive voltage pulse between negative pulses to attract electrons and discharge the target surface, thus preventing arc formation. However, this method can only generate low density plasma and therefore cannot allow full control of film properties. Also, after long runs ~ (1-3) hours, depends on duty cycle the stability of the reactive process is reduced due to increased probability of arc formation. Between 1995 and 1999, a new way of magnetron sputtering called HIPIMS (highly ionized pulse impulse magnetron sputtering) was developed. The main idea of this approach is to apply short ${\sim}(50-100){\mu}s$ high power pulses with a target power densities during the pulse between ~ (1-3) kW/cm2. These high power pulses generate high-density magnetron plasma that can significantly improve and control film properties. From the beginning, HIPIMS method has been applied to reactive sputtering processes for deposition of conductive and nonconductive films. However, commercially available HIPIMS plasma generators have not been able to create a stable, arc-free discharge in most reactive magnetron sputtering processes. HIPIMS plasma generators have been successfully used in reactive sputtering of nitrides for hard coating applications and for Al2O3 films. But until now there has been no HIPIMS data presented on reactive sputtering in cluster tools for semiconductors and MEMs applications. In this presentation, a new method of generating an arc free discharge for reactive HIPIMS using the new Cyprium plasma generator from Zpulser LLC will be introduced. Data (or evidence) will be presented showing that arc formation in reactive HIPIMS can be controlled without applying a positive voltage pulse between high power pulses. Arc-free reactive HIPIMS processes for sputtering AlN, TiO2, TiN and Si3N4 on the Applied Materials ENDURA 200 mm cluster tool will be presented. A direct comparison of the properties of films sputtered with the Advanced Energy Pinnacle Plus + plasma generator and the Zpulser Cyprium plasma generator will be presented.

• Korean Journal of Construction Engineering and Management
• /
• v.22 no.6
• /
• pp.96-106
• /
• 2021

The PC structure based on the OSC (Off-Site Construction) is mentioned as a representative method of innovation in the construction industry that converts the existing construction environment from site-centered to factory production-transportation-site assembly. However, recent research on PC method has focused on improving the functions of subsidiary materials and improving the production system to increase productivity and institutional / policy R&D that can be universally applied to the life-cycle stage of ordering / design /construction is insufficient. In particular, the absence of standardized cost calculation standards makes it difficult to calculate and verify of objectified appropriate construction cost. So which is an obstacle to the activation of the PC method. In this study, the standards for construction costs of domestic and foreign PC method were surveyed and similar Construction Standard Production Rates were analyzed to confirm the product structure suitable for PC method. Subsequently, the construction procedures and input resources for each PC subsidiary materials were identified through on-site surveys to derive component for subsidiary materials, and the factors of change in the product according to the construction characteristics(height, weight of subsidiary material) were verified. As a result the standard product calculation system suitable for the site installation of the PC method for apartment was presented.