• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.341-346
• /
• 2014

Intake E-CVVT noise, generally caused by collision sound of roller and cage clearance at idle and driving condition, is considerable source of annoyance in passenger cars using the gasoline engine. Main source of this noise is the cam torque variation of an intake E-CVVT system, and can be controlled by clearance decrease such as backlash reduction, but which may increase the manufacturing cost. Thus in this paper, most effective solution for low noise intake E-CVVT was achieved through not only reduction of backlash and cam angular acceleration but also improvement of vehicle transfer system, which is optimal configuration through acoustic sensitivity optimization of engine mount support bracket.

• Journal of Biosystems Engineering
• /
• v.16 no.3
• /
• pp.239-247
• /
• 1991

This study was conducted to investigate the feasbility of continuously variable V-belt transmission(CVVT) as automatic power transmission system of combine harvesters. An experimental set-up for testing the performance of CVVT and the automatic transmission system was designed and used to analyze the power transmission characteristics of CVVT. The transmission efficiency of CVVT was increased logarithmically with increase of the load of driven shaft, but was not affected by the speed ratios of transmission. More than 80% of transmission efficiency was obtained in the 25N-m load and more of driven-shaft, and the maximum efficiency was 88~91%. When rapid speed change of the CVVT was attempted, the speed of driven shaft was stabilized within about 0.4 seconds after shift operation in both cases of increasing and decreasing of the speed.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.675-685
• /
• 2007

A single cylinder SI engine with a VVA system is modeled by the coupling of a commercial 1D simulation package and an additional combustion model and validated by comparison with experimental data. A number of simulations are carried out to investigate the effects of five different VVA systems on the performance and fuel efficiency of the baseline engine. Finally, the simulation model is applied to an extensive computational study to map out the strategies to operate the engines with dual CVVT and dual CVVT-2 step VVL systems in a fuel-efficient manner.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.622-625
• /
• 2007

For optimizing the performance of SI engine such as engine torque, fuel consumption, and emissions, systems for variable valve timing were developed by many automotive researchers. In this work, we investigated the relationship between valve timing and intake orifice noise to improve the NVH (Noise, Vibration and Harshness) performance as well as engine torque and power. Two approaches are conducted, which are engine dynamometer testing and 1-D simulation analysis. Experimental data were measured on about 21 different operating conditions. This experiment shows that the intake and exhaust valve timing related to overlap period influence on the NVH performance, especially intake orifice noise of engine at given range of operation conditions. Similar results are achieved by using 1-D simulation analysis. It is concluded that the optimal strategies of controlling valve timing and tuning intake systems, are necessary to develop engines or vehicles with good sound quality.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3108-3113
• /
• 2008

This paper investigated the behaviors of combustion characteristics at part load condition with various intake charge motions induced by the port masking schemes in the CVVT (Continuously Variable valve Timing) engine. Time resolved in-cylinder and exhaust emissions were measured by the fast response HC and NOx analyzers to examine their formation mechanisms and behavior characteristics. As a result, in-cylinder HC decreased with the advanced intake valve timings but HC at the exhaust port increased due to the worse combustion stabilities. However HC reduction could be achieved by the application of the port maskings with a enhancement of the engine stability. NOx also decreased with early intake timings by internal EGR but increased with the charge motion controls which enhance the combustion behavior.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.286-293
• /
• 2004

The air fuel ratios of current gasoline engines are almost controlled by several air flow meters. When CVVT (Continuous Variable Valve Timing) is applied to a gasoline engine for higher engine performance, the MAP (Manifold Absolute Pressure) sensor is difficult to follow the instantaneous air fuel ratio due to the valve timing effect. Therefore, a HFM (Hot Film Flow Meter) is widely used for measuring intake air flow in this case. However, the HFMs are incapable of indicating to reverse flow, the oscillation of intake air flow has an negative effect on the precision of the HFM. Consequently, the various duct configurations in front of the air flow sensor affect the precision of HFM sensitivity. This paper mainly focused on the analysis of the reverse flow, flow fluctuation in throttle upstream and the geometry of intake system which influence the HFM measurement.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.12
• /
• pp.2183-2188
• /
• 2016

This paper deals with the design process for an outer-rotor-type surface-mounted permanent magnet synchronous motor (SPMSM) used in continuous variable valve timing (CVVT) systems in automobiles with internal combustion engines. When the same size, outer-rotor-type SPMSMs generate larger torque and more stable than inner-rotor-type SPMSMs. For the initial design, space harmonic analysis (SHA) is used. In order to minimize the cogging torque, an optimization was conducted using Response Surface Methodology (RSM). At the end of the paper, Finite Element Analysis (FEA) is performed to verify the performance of the optimum model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.65-73
• /
• 2008

The purpose of this study is development of universal engine model for integrated Hybrid Electric Vehicle (HEV) simulator and a optimization of engine model. The engine model of this study is based on the MATLAB Simulink for universal and include engine fuel economy technologies for HEV. Various engine fuel economy technologies for HEV is estimated by commercial engine 1-D simulation program - WAVE. And, the 1-D simulation model of base version is compared with engine experiment result. The analyzed engine technologies with 1-D simulation are Dual-CVVT, Atkinson-Cycle and Cylinder-Deactivation System. There are improvement of fuel economy and power performance with Dual-CVVT model at part load and full load, pumping loss reduction with Cylinder-Deactivation System at idle and regeneration. Each estimated technologies are analyzed by 1-D simulation on all operation region for base data to converse simulink. The simulink based engine model maintains a signal with ECU for determination of engine operation point.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.14-22
• /
• 2010

Hybrid Electronic Vehicle (HEV) is one of the solutions of high oil price and environment problem. Recently, study of HEV is important for automobile industry. However HEV has a lot of components and there are many cases for assembling, it's impossible to test results from assembling by using real vehicles. To solve this problem, hybrid system simulator is required. The purpose of this study is to develop and optimize of engine module for hybrid system simulator. The commercial 1-D engine simulation program, WAVE is used to get the engine capacity and performance data and 1-D simulation model of base engine is compared with engine experiment results. Using the data, the engine module is developed based on the MATLAB Simulink. There are blocks of base engine, Single-CVVT engine and Dual-CVVT engine. The effect of acceleration and deceleration is applied to each engine block. In addition, the control and processing logics for CIS technology are developed. Finally the simulator operates FTP-72 mode test.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.3
• /
• pp.317-322
• /
• 2011

This work has investigated the exhaust emissions such as Total Hydrocarbon (THC), Nitrogen Oxides(NOx), and Particulate Matter (PM) characteristics emitted from the tail-pipe of a continuously variable valve timing (CVVT) gasoline-fueled engine with different intake valve opening timings and injection pressures at the part load condition. Valve overlap period was varied from $40^{\circ}CA$ to $10^{\circ}CA$ and fuel injection pressure was increased from 3.5 bar to 5.0 bar. THC and NOx emissions decreased as intake valve opening timing was advanced regardless of fuel injection pressure. When the fuel was injected with the condition of 5.0 bar at all of valve overlap ranges, THC levels were reduced by 55%. NOx concentrations were diminished about 75% as valve overlap increased. PM size distributions were analyzed as bi-modal type of the nucleation and accumulation mode. Comparing with fuel injection pressures, PM emission levels were decreased at high pressure injection of 5.0 bar condition.